It was a local appliance part store. It was open to public and repair companies. I called several on my area before I found one that carried the part.

Glad it helped you get it fixed. Good job!

Which plug are you referring to please?

Sure thing. Thanks for watching it.

If you push the buttons in the order at the beginning of the video the error code should pop up. You might have to try a few times.

Then I researched the code it self with Google:)

It was from a local contactor/public supply house. I called around until I found one. Have your part number with you when you call.

@@jkay4209 ok Thank you so much

Agreed!

@@jkay4209 had to replace a valve solenoid body on mine then it would not work. Turns out it needed a $350 button panel! Of course, no warranty for that part. The cause? Steam from the water leaks up under the control pane, rotting out some surface soldered components. Recommend you seal the gap between the button panel and the washer body so condensate cannot form under the interface.

@@mcw0530 Good to know. I ended up replacing the unit when it had an issue again during the beginning of COVID when everything was shut down. I was over it at that point.

I agree!! It happened again about a year after the video and I now have a different washer!

@@jkay4209 we're a family of 6 so we NEED a large capacity washer\dryer. But when this one goes, as I assume it will, I've already said we're buying a commercial grade appliance.

That is awesome to hear!! That’s why I made the video, hoping to help save some people money and time!

Happy the video helped you out! Thanks for your kinds words.

That’s awesome!

Dang it!! I hope you can get the code Atleast. It should be the same process for the dryer as the washer. Good luck

I called around and found a local supply house.

It happened again so we got a new different brand washer this time!

If I remember right the board had little clips that went in a certain way. The board it self ad a bunch of connections that are soldered together.

That’s awesome. Thanks. I actually had the same thing happen two more times, about 6 months then they were in storage with my move for 8 months. Then It happened again after I used for a few months once moved in. I have replaced the unit at this point.

Good job finding out what it needed. I was dissappointed with their warranty too! Hopefully it’s still running for you.

Thank you sir!! You’ve allowed me to fix my washing machine by sharing this file

@jp just over 1 year old and its needed 1 board and 2 panels. Its obvious that it's trash.

For real, Completely agreed. Never again with Maytag.

Glad it helped!

Underneath, you can pop them out.

Yes it was hard to do that way. I think you may be able to get them off easier if you take the back top panel off and go through that way.

I ran into this issue today. What worked best for me is to remove the other three screws from the back. Slide the whole top lid of the washer forward and lift (takes somes finesse) so you can get underneath the top panel. When underneath you'll see the metal clips protruding. I pushed on them with my thumbs while pulling the console off and rotating backward off the lid. The left clip was a little tougher than the right clip. So you can use a screwdriver to push against it. btw, I'm still trying to fix my washer. The normal light is just blinking. Nothing happens when I turn the wheel. I was able to get into diagnostic mode but finding good instructions is difficult. I'm still searching.

That or from under neath. It was a pain!!!

I did the same and viola, it worked. Probably going to order the panel anyways...

Joel, muchas Gracias! Same issue down here in Mexico with the Maytag bravo! I did exactly the same as you mentioned....and works muy bien! Thanks for your advice!

Still going strong here a month later.

Joel C . Thanks for your input, I did the same and it worked!

Awesome!! Good to know in case I run into this. Thanks!

Glad it helped!!!

Whoo hoo!!! Glad the video helped.

Thanks. My units have been in storage between a move so if I have problems again I. The future I will keep that in mind. Good to know thank you!

Jeremiah Johnson so you had this same problem and it was a bare wire like hers in this video? I'm having the same exact issue she has.... No power on user interface when plugged in but diagnostics show ALL buttons work on the interface.

Yes I did google it. I can google yours and see if I can find anything. I will check back ahortly

I googled “maytag bravos washer f5 e1 error code” and there were a couple videos that came up. Check them out and hopefully they will help you to solve the problem

Same issue here. All buttons work because we can get into diagnostic mode and that's where we get error codes. Need a less expensive option than buying a whole new display though...

I hope you were able to get it fixed. The parts are pricey. I found an appliance store that allowed returns which is why I was able to go back to the next part in sequence of the repair.

That’s no fun! Sorry to hear. Hope you were able to get it fixed.

Maytag Model mvwb835dw0 Control Panel Assembly W10861510

ThNks Fred. I had to take a picture of the serial tag on the part.

Yayyy!!! Great news! 🤙🏼

When you are looking at the clips from the back, pull the part of the metal clip furthest away from you back towards you. This will release the front. When it pops up, push the interface toward the front of the washer . this will release the back.

Sorry I’m not on here regularly. Thanks John. I used a putty and it was tough to get it off.

A putty knife is very hard (impossible). Check out " Bearded Appliance Repair" kzbin.info/www/bejne/gmmVhKevarJkkKs for a very easy safe way to do it.