@ashutoshchandra8237: Glad it helped.

@leonpagliari7352: Happy to help. Thank you for subscribing to my channel.

@LastMooseStanding: It might be from the HMI firmware or the resolution or the version of the HMI (Standard or Performance).

@ricamonta899: I have not tried it but I think it should be able to.

@@SYPHOANG ill give it a shot, I know I might have to do some logic on the controller side.

@rangeralone6181: Tôi cũng mắc lỗi tương tự ngay lần thử đầu tiên. Bạn chỉ cần nhấn mạnh hơn một chút và giữ lâu hơn một chút.

@rangeralone6181: Unfortunately I have not experienced it before.

@tanachaiphoset3451: Happy to help. Thank you for subscribing to my channel.

@ibrado900: Thank you for subscribing to my channel.

@ansonkiek6471: 1k, 2k ? Would you please explain it a bit more?

@@SYPHOANG my data write until 2k then stopped for example file created on 7/31 , I see only store until 2/9 and stopped working

@ansonkiek6471: I still don't understand what do you mean for 2k? is 2k a year? is 7/31 a date? do you have data logged into an SD card? or the HMI internal memory? if it's logged into the HMI internal memory, it might be full and stop logging.

@@SYPHOANG 2k is data store in CSV row , and I use usb store my CSV data I see my CSV file in pen drive created in 7/31 and CSV last recorded only until2/9 how possible stop due to hmi internal memory full ?

@ansonkiek6471: I guess 7/31 is July 31st and 2/9 is February 9th? You might need to check your "trigger" tag.

@quoit99training83: Thank you for your comment and your support to my channel.

@luctranvan4273: Cảm ơn bình luận của bạn. Vui lòng xem video bên dưới để biết hướng dẫn mở .cha file đã tải trên Connected Component Workbench. Nếu nó hữu ích và bạn thích nội dung kênh của tôi thì một "super thanks" sẽ là cách tuyệt vời thể hiện sự ủng hộ của bạn đối với kênh của tôi. kzbin.info/www/bejne/fYechKNubcyDgZY

@kenneym2003: Glad it helped!

@bryanfrancisco-t7x: Happy to help!

@GeekendZone: Thanks for your comments but I am not familiar with DNS, never tried it before.

@ghuy6073: Thanks for your comment. I think it should come with Modbus TCP. There are a few things you might want to check. First, make sure you have the right register mapping. Second, slave ID might matter. Make sure you call out the correct slave ID on your master device. Third, be specific on the register length or count. Do not set the length too long or pick up too many registers. If the registers are not available at the device and you are trying to pick them, it might give you errors too. Good luck!!!

@PLC-79:Thank you for your kind words and your support to my channel.

@plc24_max10: Unfortunately, I don't think it is possible.

@carolinadiaz0126: What you need is "Audit Trail" and "CSV Export". kzbin.info/www/bejne/aHXPmZyDoc1ojNksi=ztyJBiZ4N5aUBfxi kzbin.info/www/bejne/p4rEpZWto7l3sKcsi=0b6gVPKDGYbyVgJs If you like the content of my videos, a "super thanks" at the lower right should be a great way to show your support to my channel. Thank you.

@kurtklingbeil6900:.

@mdlutforrahman4544: Are you trying to modify the existing HMI application (.mer file) on the HMI? ME TRANSFER UTILITY is a tool for you to download/upload an HMI runtime/application to/from an HMI from/to your computer. An .mer file is for an actual HMI only. If you need to work on it. You will need 2 more pieces of software. "FactoryTalk View ME Application Manager" to "restore runtime application" and "FactoryTalk View Studio ME" to work on the restored HMI application.

@PauloFonseca-z5s: Glad it was helpful.

@elianousdu30: USB sticks should be formatted to FAT32. The path is always the same. Thank you for your comment.

@@SYPHOANG Thank you very much !

@sakurag55: Thank you for subscribing to my channel. Is your device from Allen Bradley? Sometimes you might have to remove the driver and re-configure it again. If you want to do it automatically, you should select "Ethernet/IP driver" under "Available driver types". After clicking "add new", make sure you select the driver that has your computer IP address on the same network with the device that you want to see in "Rslinx". Hopefully this helps.

@RohitSormasf:???

@dewalaknat8732: what message you got on the HMI? what is the error code?

@abrarahmednabil1283: Thanks for your support to my channel.

@zainshafiq1923: I have not tried the other port but I believe it's very possible. you can use it as a different serial communication interface to talk to the same slave/server device. If I have some free time, I willing definitely test it out for you.

@dychristerchrister6477: You might want to check out the video below. If it’s helpful, please do not forget a “super thanks” to show your support to my channel. kzbin.info/www/bejne/r6TFfHinhbeSh6ssi=hItfJvWy4U3ptOfO

@abrarahmednabil1283: ???

@AbdullahAhmed-vj2vi: Thank you for your support to my channel.

@@SYPHOANG you deserve more than like 👍..

@AbdullahAhmed-vj2vi: Thank you for your kind words. If you want and you feel comfortable, you can give me a "super thanks" at the lower left corner. Thank you :)

@maicolherrera7685: "DCOM" means DEFAULT COM. Default Com is DF1. Once you change the Communication Protocol to anything but DF1, the DF1 light will be turned OFF. But what should be the communication protocol for the channel is the question for you. You can look into the other device that your PLC is connected to and find out what communication protocol and configuration it is looking for from your PLC. Hope that helps. Good luck

@@SYPHOANG cuando hago la descarga con la modificación del Chanel 0, el PLC me impide conectarme otra vez y por eso no me deja ponerle run

@maicolherrera7685: It's very simple. You pressed the button on the PLC to set the default DF1 to Channel 0, the DCOM turned ON. However channel 0 in the program you downloaded to the PLC is configured for DH485 or anything but DF1. My guess is DCOM light turned OFF after you downloaded the program to the PLC because channel 0 is now no longer set for the default DF1. You can no longer connect to the PLC because of the cable between your PLC and your computer. My guess is the cable you use is for DF1 communication protocol, it is not for the communication protocol for channel 0 in the program you downloaded to the PLC. I think that was also the reason you set the default DF1 to channel 0 on the PLC. If I was you, I would never reset channel 0 on the PLC back to DF1. My recommendation is to always find the right cable that works for the communication protocol configure in the PLC program before any downloads. Please consider joining my channel for more support. kzbin.info/door/yyYzqg0sp_W7CW9ScZh-zAjoin

@vleiswalker9374: Glad it was helpful.

@user-fb9rd2dl4l: Unfortunately I don't think that would be possible. However you can look into your scada system to find out what communication protocol and configuration it is looking for from the micrologix1200 PLC. Then you can set it up again in the PLC logic. Good luck.

@@SYPHOANG muchas gracias, asi lo hare es que eso es lo curioso cuando por defecto la comunicacion al presionar el boton com, se visualizan unos datos en el scada, y al apagar el plc, se dejan de ver esos datos

@khachapatrachatamethin7484: which document in my dropbox are you trying to download? The full links might be available for channel members only.

@khachapatrachatamethin7484: Are you Samroeng Kanathong who is trying to download the function block "Lead_Lag_STBY_BLK.7z"? If you can confirm it is you and that is what you need, I can share you this file only as an exception for a potential channel member. All function blocks are for channel members only. Please consider joining my channel for more support. kzbin.info/door/yyYzqg0sp_W7CW9ScZh-zAjoin

@@SYPHOANG thank you so much. I can reach out to your document right now. I wonder how to convert XML file back to Excel file. Could you please help?

@khachapatrachatamethin7484: Are you trying to download the function block "Lead _Lag_STBY_BLK.7z" and import it into your PLC project in Connected Components Workbench? If so, you need to download and import the file with ".7z" extension into your PLC project. No need to worry about other files.

@@SYPHOANG nope.

@punishedgoy9131: Thank you for your support to my channel.

If we check the Expanded box at 1:06, how much can it expand? Isn't the maximum length of N File only 255?

@yijunhuang1005: Thank you for your support to my channel. Yes, it might be 255 max.

@yijunhuang1005: Glad it was helpful!

@T---dq2qv: In the "FactoryTalk View Studio", at the very top, select " Application", then click on "Create Runtime Application". Be careful to pick up the right version for the .mer file you want to create at " Save as type"? Make sure its version is lower than your HMI firmware. Good luck.

@Man_Arm92: You're welcome!

@simonngo7085: Thank you for subscribing to my channel. I have not tried it with any Allen Bradley PLC but I think it is very possible.

@punishedgoy9131: Glad you found it useful. Thank you for your support to my channel.

@punishedgoy9131: It is Secomea SiteManager 1549.

@@SYPHOANG please please please make a video on the site master

@punishedgoy9131: Thank you for your interest in the Secomea SiteManager 1549. Below video is what you might want to check out. kzbin.info/www/bejne/d6bcZpVqZbF7nbssi=0uyJTLIuTSko2mhf

@T---dq2qv: firmware and software version are different. They are not exactly the same. The software is what is installed on your computer while firmware is what is installed on the controller. The key point is firmware version ALWAYS need to be higher than the software one. Hopefully that clearly answers your question.

@@SYPHOANG thanks you very much for this anwser , so the firmware version alway need higher than sorfware one , such as Firmware version is 20.019 and firmware version do not higher than 20 such as 21.00.00 is it right

@@T---dq2qv Correct.

@InstrumentacionExterran: No, this is "Connected Components Workbench" software.

@InstrumentacionExterran: ACD files are for Studio5000/ControlLogix or CompactLogix PLC's. This is Micro800's PLC that uses Connected Components Workbench for programming.

@YohDave: You can use "STRING" data type and get up to 82 characters for each tag.

@@SYPHOANG Thanks! Do you know how can I write the serial number in the tag? Or how can I link the tag with to the serial number?

@@YohDave From programming perspective, you create a "string" data type tag in the PLC program and then map it to the HMI for a manual data entry. I am not sure what you meant for "serial number"? Are you trying to connect your PLC to a barcode/QR code reader/scanner? If so, I am not familiar with these devices.

@@SYPHOANG Thanks!

@karthikvhiremath1886: This is the right video for you. But do you have all the information you need for data mapping? You need to know the IP address, subnet mask, the configuration of the power meter as well as its Modbus data mapping.

@@SYPHOANG Thank you sir... I got one fbd from your video for 2 WORD TO REAL converter FBD absolutely working ultimately... So I need one more Instruction REAL to 2 WORD CONVERTER... If you have please give me link....

@CongDucDinh-s6c: Bạn có thể tải xuống từ Rockwell Automation.com. Nó sẽ cho bạn thời gian gia hạn là 7 ngày để dùng thử. Sau 7 ngày, bạn sẽ phải mua giấy phép từ nhà phân phối ủy quyền của Rockwell tại địa phương. Đó là cách tôi có được phần mềm tại nơi làm việc.

@joaopaulopaul: ? Who is he?

​@@SYPHOANG precisando do software do GP 2301 proface

@hchangv: The password I entered at 2:15 was set up earlier (not in this video). When you first power up a brand new HMI out of the box condition, it will prompt you to create it. There is no such default password coming from Allen Bradley. If you lost the password or simply do not know it, flashing the HMI firmware might wipe out everything including the password to allow you to set it up again. Thank you for your comments.