Hi Alex - When I unplug the dryer and plug it back in, I get dr 04.00 DS flashing and I cannot power up the machine. Any idea what that is? Thanks! It's a residential stacking washer/dryer. It goes off after a while and I can use the machine Strange...

Excellent video! Thank you very much!

How good are those thermostat? I want to replace the dial type thermostat to a digital one like the one in the video?

This is a must watch, it fixed my problem!

Ypur awsome❤

good installation!

So if the grease in the splines of the agitator bell are washed out, then plastic shaft spline seal fails, the water just slides down the inside of the rubber seals down the shaft, down over the top bearing and through it, then down to the lower bearing, and then out onto the transmission. The only thing stopping water from moving under the water agitator bell is the small amount of grease you added to the splines of the agitator bell. The plastic spline seal that fits around the threads of the shaft for the hex nut seal, and the hub sitting on the rubber seal are both not using any sealant to fill small spaces water can travel into. Which is how water was able to get down into the shaft. In reassembly pack the hub under the top bearing with a hard to wash away waterproof grease that does not degrade plastic or rubber. Use the grease around the base of the plastic spline seal as well to keep water from moving past and starting the rust seen around the threads. Before installing the agitator bell, also apply grease between agitator bell and top bearing to shaft and seal to keep water from sliding by. The areas in the hub left ungreased leave plenty of room for water to move by. If one chooses, use a bead of waterpump rtv at the top of the nut then push it into the nut and threads with finger before installing agitator bell. As it will move out to of the way with a pick the next time you want to remove the hex nut, but will create a seal and disallow water from moving between the hex-nut and shaft.

Good Job. Looks like it's time to replace all of the rooftop units as well.

Great video. Easy to understand and follow. Thank you for sharing and appreciate the simple instructions. Will click to subscribe going forward.

Four 1500W heaters would be too much for the circuit and thermostat in this video, correct?

Alex I have a question on my refrigerator it's a GE refrigerator but anyways as far as the fan on my refrigerator well on the bottom back right side across the compressor it turns off out of nowhere and either I have to disconnect the refrigerator itself or also I mess with the electrical box turn it off the refrigerator and the kitchen switches well I'm just asking what does that mean if you know?

Excellent tip, this solved my problem, thanks a lot!

Thank you 🙏

I have 15 of these in my house and I cannot believe you didn’t bring up or talk about the only reason every single one of mine break every time The thermal cut off switch sticks on cutting the power off over and over again. It gets old and then flips on, even though it’s not too hot. And then it stays on. These switches are junk and ruined these heaters. It is the only part on the heater other than the heater element that is extremely necessary to talk about you could do a whole video on this switch along.

Wonder if a vegetable peeler would work to do the trick for shaving backside die outside corners? Especially for newbies who might be nervous to cut themselves?

Thank you very much Alex!! Great video. I couldnt figure out why my new tap wouldnt retract. The instructions they came with werent great and Im a first time installer :) Your video is the only one I saw in 10+ videos that showed the plastic spacer inside the metal piping which made me realise that was the spare part I had after install. Thanks again.

Thank you!!!!!!!

Found this by luck helped save alot of time great job on the video and thanks alot for it

Shouldnt that be a 20 amp braker ?

Hi Alex, I'm not getting any power to the igniter on my speedqueen dryer. Help!

i have an installer coming today to put in my new toilet. as i know nothing about this type of job i thought i should educate myself a bit. thank you for your excellent video.

How do I fasten the stovetop to the range?? My clips fell out and I don’t know what to do!

Good job!

😎

Awesome video

Nice job!

Thank you so much. Oh my goodness. It's so difficult to find videos on fan coils. 😢 Where is the drain pipe? Is the safety switch also connected/can it be connected to the drain switch?

But you had a 45 Degree fitting there. Just remove that fitting and replace that section with anything but galvanized.

Great video.

I have the same b& g pump / I wish you had it turned on before and after to hear difference. But nice to see procedure. Thx

What's the capacity of you nitrogen cylinder tank?

Martin Jeffrey Brown Maria Lewis Jennifer

Nice if its under 100 ft my is at 700ft only producing 1gpm

Thank you, very clear instructions with complete information. Videos like this are why I go to KZbin instead of manufacturers website.

Great video. You ain't no handyman. You's a damn HVAC tech

I just watched your video. We have Crane taps as well. We had a drip so we called in a plumber annd he ordered new cartridges. 3 times he has had to come back because now while having a shower the taps slowly start to turn off... untenable situation. What could be wrong? He's returning again tomorrow......any thoughts would be greatly appreciated 💕. Neww sub

Absolutely 100% definitely a bad repair never use compression couplings for galvanized. Use a threader or heat up fitting and run new copper or pecks from there never do it like this.

Both sides of that pipe must not be able to move. The side where you put the valve can blow out. This is a poor repair .

Amazing video!! Thank you!!!!

I love how you tech thank you very much

The next plumber will thank you use some pipe dope

I love my ferrule puller!!!

Ancient caveman boiler maintenances 😅

Amazing video! Thank you! I love your explanations, and drawings. Easy to understand.

thank you for the great video. just to get you a heads up on this GE microwave you would have seen that only the last screw all the way in the left was the only one that needed to be removed The other three weren't in the way so you know next time just remove the last one.

What is the plastic part called at 6:07? I need a new one. A screw snapped, so the plastic sleeve was damaged getting it off. I got the replacement balancing unit, but it didn't come with the plastic sleeve and I've been having a really hard time tracking it down.

Sir Alex, good day to you sir. Pardon my question, "What is the name of the product that you used to test for leaks, instead of the soapy bubbles in a spray bottle. I thought that was an interesting product in your hands. Thank you.

God damn octopus 😂

Thank you for not trying to make this a 10 minute video

Great video thank you