Ray craft

Пікірлер

@InternetUser-ds4bn 21 сағат бұрын

❤

@InternetUser-ds4bn 23 сағат бұрын

Hi bro what transmitter u planning to buy in future

@raycraft3990 23 сағат бұрын

@@InternetUser-ds4bn Fsi6s

@InternetUser-ds4bn 23 сағат бұрын

@@raycraft3990 why not pocket or boxer

@InternetUser-ds4bn 23 сағат бұрын

@@raycraft3990 can i get ur no

@raycraft3990 22 сағат бұрын

@@InternetUser-ds4bn expensive + no warranty + expensive and rare reciever

@raycraft3990 22 сағат бұрын

@@InternetUser-ds4bn You may contact me here

@DevBuildup 4 күн бұрын

Hi bro

@AlbertoRodrigues-xi3ue 5 күн бұрын

Aviãozinho

@daviddavids2884 7 күн бұрын

0006 part of the rudder is NOT supposed to be removed. you have THREE options. locate the rudder just forward-of the elevator hinge line, or make a SPLIT elevator, or use two pushrods and control horns. 0128 in relation to the stab span, the vert-stab should be about one inch taller. 0827 this is a SF prop. if the SF prop is noisy, a stiff E prop should be used. is an eight inch SF prop compatible with the motor's spec's. 0953 Servos & rx go NEAR the cg, not aft-of it.! googletranslate

@raycraft3990 7 күн бұрын

I appreciate your knowledge and thank you for sharing it with us . Wish you a happy day 😊

@adarsharoy8857 7 күн бұрын

Next time udabo ekshathe🫶🏻

@Sprkychild 18 күн бұрын

We Doing minecraft irl!! Im sorry the music reminded me of minecraft

@nischalpoudel3042 23 күн бұрын

Where is the flight video

@raycraft3990 22 күн бұрын

It doesn't fly well because of worse weight distribution but I will tackle this issue by changing the frame and some electronics .

@muhamatafif8662 23 күн бұрын

Tes terbang

@adarsharoy8857 Ай бұрын

well done👍👍

@nischalpoudel3042 Ай бұрын

Nice but you didn't show the electronics part well. How will someone who is a beginner will understand?

@raycraft3990 Ай бұрын

Hmm You raised a serious issue , ok I will show the electronics part in a seperate video , Very soon .

@nischalpoudel3042 Ай бұрын

@@raycraft3990 I like your content but most of your rc plane videos have incomplete explanations.

@Shrutisthetic Ай бұрын

Brilliant!

@manojitsaha6262 Ай бұрын

awsome ❤❤❤

@Animate_Laughs Ай бұрын

Whts ubes and why its used ?

@raycraft3990 Ай бұрын

Some esc don't have 5 volt output . so we need to connect an external module to get 5 volt supply for powering reciever . From this particular frame of reference, that 5 volt supplying module is known as ubec . If some esc have inbuilt 5 volt output , in such case connecting an external ubec is useless .

@divineangel825 Ай бұрын

RAY CRAFT CHANNEL OWNER You are very blessed, powerful and fortunate soul. UNDERSTAND THIS: My soul brother, we all have TWO fathers our Soul's Father SHIVA/GOD/ALLAH/EK ONKAR / LIGHT /POWER FATHER OF ALL SOULS on Earth and second our Body's birth father. Remember SHIVA as I the soul child of Supreme Soul Father SHIVBABA. Have a Great Wonderful magnificent future ahead with excellent health, wealth and prosperity 🙏🏻⚘️😊 SMILE LOVINGLY AND SAY OM NAMAH SHIVAY 🙏🏻⚘️😊 ALL THE VERY BEST FOR YOUR CHANNEL 🙏🏼💐🌼

@raycraft3990 Ай бұрын

Your message resonates deeply with me. I genuinely appreciate your thoughts and value your sentiments. Thank you for sharing your thoughts and for your kind wishes. Wishing you a joyful day ahead!

@prowingplane7380 2 ай бұрын

Nice bro

@user-dk8lk4tz2o 2 ай бұрын

ماهن تك القطع الثلاث واين اوجدها

@user-dk8lk4tz2o 2 ай бұрын

هل سوف تطير لااعتقد انها سوف تطير لماذا لاتصنع حجم اصغر من هذا الحجم وسوف تطير ❤

@user-dk8lk4tz2o 2 ай бұрын

من اين اتيت بقطعه التحكم بطائرة من فضلك اجب علي

@Sonofadsab 3 ай бұрын

Nice toys

@nischalpoudel3042 3 ай бұрын

Awesome video. Can you try to make this same design using cardboard

@raycraft3990 3 ай бұрын

Will try

@salilworldin 3 ай бұрын

Wow

@nischalpoudel3042 3 ай бұрын

You don't explain anything you don't share your plans. How will your channel grow like this?

@raycraft3990 3 ай бұрын

This is 3rd part if you want to know all the dimensions , making process , watch part 1

@RatnadeepMalakar 3 ай бұрын

Only 4pes chaya

@RatnadeepMalakar 3 ай бұрын

Please help me muje 3mm Depron sheet chaya 😢😢

@raycraft3990 3 ай бұрын

Ji shuniye , amazon pe abhi depron sheet out of stock hai toh Thora wait kr li jiye stock ane tak , firr uddher se le lijiye. Agr apko depron sheets nehi mil rahe hai toh app thermocol se bhi bana sakte hai , compressed thermocol ho toh jada bahatar rahega Thermocol se banaye hue plane ki video bhi bohot jald ane ko hai . Wish you a happy day

@RatnadeepMalakar 3 ай бұрын

Brother me apka Subscriber hu

@RatnadeepMalakar 3 ай бұрын

Only 4pes.....

@RatnadeepMalakar 3 ай бұрын

Please help me muje 3mm Depron sheet chaya

@RatnadeepMalakar 3 ай бұрын

Bro me apka Subscriber hu 😊

@KalibasauRC_64 3 ай бұрын

Nice rc

@daviddavids2884 3 ай бұрын

Z-BENDS should be used at pushrod ends.!!!!!!

@daviddavids2884 3 ай бұрын

1:00 RUDDER goes on the LEFT Stick.

@daviddavids2884 3 ай бұрын

information :37 when installing power and control components PUT them ALL NEAR the cg.!!! then, AS necessary, move mass away from that spot so that the cg is at thirty percent of chord. these servos are TOO FAR aft-of the cg. putting mass/servos high in the fuselage is NOT recommended. bc doing so Affects the model's dom. distribution of mass. the offset pusher thrust config is STILL Wrong.! :46 the span of the horiz-stab should be Equal to Thirty percent of the wingspan. the span of the elevator should NOT be truncated, at the stab tips. googletranslate

@technocrat9984 4 ай бұрын

Plz provide the program link

@raycraft3990 4 ай бұрын

I apologize, this code is currently under development and may undergo further refinement. I may share the code once it has been optimized for efficiency.

@user-dk8lk4tz2o 2 ай бұрын

@@raycraft3990نريد رابط البرنامج من فضلك ❤

@daviddavids2884 4 ай бұрын

because of the wonky thrust configuration, thrust will produce nose-down moment; ALL the time. the elevator can be trimmed to compensate for that moment. but that trim will be a continual source of 'extra' drag.

@raycraft3990 4 ай бұрын

Your willingness to share your knowledge is truly appreciated. It enriches our understanding and empowers us to grow. Your contributions make a meaningful difference in our journey of learning. We are fortunate to benefit from your wealth of knowledge and experience. Your kindness in sharing insights inspires us to strive for excellence. We deeply value the guidance and wisdom you offer.

@daviddavids2884 4 ай бұрын

2:41 rudder goes on the LEFT stick.!!!!!

@daviddavids2884 4 ай бұрын

ideally, the cg should be located at Thirty percent of chord. the main spar should ALSO be located at thirty percent of chord.

@daviddavids2884 4 ай бұрын

the distance between the main wing and stabs should be roughly equal to Two wing chord lengths.

@daviddavids2884 4 ай бұрын

1:56 the span of the horiz-stab does NOT need to be greater than Thirty percent of the wingspan. the span of the elevator Should extend TO the stab tips.!

@raycraft3990 4 ай бұрын

I am truly grateful for your generosity in imparting your valuable knowledge with us.

@daviddavids2884 4 ай бұрын

information 1:08 servos go NEAR the cg.!!! not aft-of it. this is a vertically offset pusher thrust configuration. as such, a CERTAIN thrust LINE should be used. at linked photo IGNORE the words. just SEE what a correct thrust configuration looks like. googletranslate static.rcgroups.net/forums/attachments/2/9/6/3/9/7/a5988257-224-bixler%202%20motor%20angle%20correction.jpg

@sajidakilledar779 4 ай бұрын

From where did u got that brushless motor? Can u provide link

@raycraft3990 4 ай бұрын

Check description

@artsoumen6510 4 ай бұрын

Vai transmitter kaise banaye 😢

@raycraft3990 4 ай бұрын

kzbin.info/www/bejne/mHWao4SYo7iVm80si=rM1pnY8Ig1FT_oit

@dhirajbanpurkar5397 4 ай бұрын

which esc do you use and plz give me link

@raycraft3990 4 ай бұрын

Check description

@dhirajbanpurkar5397 4 ай бұрын

how to make arduino transmitter and receive

@raycraft3990 4 ай бұрын

@@dhirajbanpurkar5397 kzbin.info/www/bejne/mojUYWysqchjja8si=-So0krQZYr70GZt3

@raycraft3990 4 ай бұрын

@@dhirajbanpurkar5397 kzbin.info/www/bejne/mHWao4SYo7iVm80si=ZVro5vVXDvmxfptD This one is simple

@dhirajbanpurkar5397 4 ай бұрын

but how to connect receiver with drv8833 module plz help

@sajidakilledar779 4 ай бұрын

Hey please can you share the full plan?

@raycraft3990 4 ай бұрын

Apologies, but I'm having trouble understanding your message. Could you please provide more context or clarify your question?