Is there ball bearing between the reciprocating slides??

What size sprocket does the 36 take?

Your awesome

Spectacular

How did u do the middle

Mute mechanic

Thank you !!

What is the part number? I dont see it anywhere

Great video, saved me a lot of time. If this is on your list, don't screw around trying to save a few steps. Whether your compressor is upper or lower, remove the fan shroud. Ask me how I know.

What settings did you use?

I dream about this

Where can I buy these brackets? Need 2 for an 05 sierra

Careful with pressing berrings. They squeeze too far easily breaking

The fuel consumption of my chansaw is dreadful.

2 years ago. Is it still holding up?

you what?????

Awesome! Did you have any issues with the main drive belt jumping off the pulleys with the change in direction?

That motor mount is dope great idea

Thank you for posting. That was a great application. Can it go uphill ok?

I got washers in my kit. where do they go?

Thanks !!!

thanks for the tips man.

Bravo. Best instructional video I've seen no wasted time with comments. Perfect

Can you tell me what kind of bar it mounts? (holes, length etc)

watching this gave me the confidence to give it a go. Knowing it didn't involve freon, reassured me that it was within my skill level. Every garage wanted to replace the entire compressor (at a cost of $600~$650) it's not their money, so why would they care? In spite of me telling them it was a faulty clutch & eBay sells them for $45. I get the last laugh by saving $600~ish. thanks for uploading this video!

I like your video stile!

I really really appreciate how simple and to the point this video is, thank you

Thank you so much for this video. I was searching for videos on (plan ideas) on where and how to place the reductor. Thank you!

Give this guy an Oscar or an Emmy for this video... to the point

I got a 2002 Chevy Silverado 2 by 4 both cross members are gone I got to replace both of them that's the way to do it Wilderness new tabs on that's not going to last the cross members will rot out next and you'll be alright we'll be worse off than he was

Well done good sir.

Perfect! Exactly what I wanted to know - thanks for sharing! Now I just need somebody to show me how to set a steel pipe in solid concrete in an old tire full. We had two when I was a kid but my maker dad also died when I was a kid so...I have no idea how he did it so that everything stays together and there is zero play in the hole the pole's set in. The wind never even swayed them. They'd just sit there - and that was back in Kansas. Which gets super windy, super storms and super hail - in case anybody doesn't know that. They were the handiest things. Two of us could just tip one a bit and roll them wherever we wanted them. They were super heavy but it didn't matter. They'd just roll along wherever we wanted them and when they were set there, they would not move. For us, we'd put them wherever we wanted to hang something heavy or set up a badminton net or whatever. It was super heavy with salvaged super thick walled 2 inch stainless steel pipe (or, at least, it wasn't rusty) about 7-8 feet tall, which I doubt I can source but I also don't need that sort of strength. I believe they used them with a chain hooked between them and a chain lift for engines and stuff but I don't need that kind of heft. What I need is for it to stay put in, say, 80 mph straightline winds, which any heavy pipe could do. We've had winds in excess of 70mph TWICE over the past 3 years. We've been getting some sort of crazy winds and down bursts for about 6 or 7 years...

No filter? You should consider adding one!!!

Easy and practical!!

cool mod.+ your garden will love you

Great video man! But question do you know what size breaker bar you used and snap ring pliers size?

How can i tell if it's the clutch thst needs replaced vs the entire compressor?

Was a hot day because my 2006 same thing ram 1500

Very helpful thank you.

Thats too high. The barrel wont ever stop being filled. It needs to be level.

Lenz's Law

Eeaaaaaahhh k k k klu

Copper in the penny and the quarter, no copper in the nickel.

Nickel Left the Chat

Wtf is the nickel made of? Wax??

wow eddy currents

How is it holding up?

i did it by mounting the engine above & behind the axle, after rotating the transaxle 90°, so the input was horizontal. I then connected the two with a 1000rpm centrifugal clutch & #35 chain. it went over 25mph with a stock Predator 212.

This is how a KZbin video should be done

Love the crashes. This is actually brilliant for landowners with trails. Keep chainsaw with you and have the power. I’ve got the 80v chainsaw but same idea. They also make a 6” hand chainsaw I keep in the Polaris.