The directions state to use anchors

I purchased this damper and a couple kitchen cabinet doors not closing all the way….how do I correct

I hate hate HATE these crappy brackets! broke both pain in the butt bracket pins and now I can't find replacements. going to throw the whole thing in the trash.

It’s 2024 and I’ve been trying all day to find bathroom hardware that mounts like this. I guess with the negative reviews I see why it may have been discontinued but that makes me sad because I LOVED this system. Used in 2017 for 3 bathrooms. Not only was it easy to install, not only did they ALL stay rock solid, but they were also a snap to remove and replace without tools for painting. Sure it was usually a two-handed operation, pretty tight, but I never had drywall tear out or any big problems. So much better than the screws that loosen over time, are sometimes hard to align, wear out, and wobble around. Unpopular opinion, but I’m seriously in the market to snatch them all up if they’re going out of style.

How much weight can this toggle bar hold?

How can both ends be screwed into studs? Studs are 16" apart. No one makes bars in 16" increments.

OMG. Just finding this video. Out toilet paper holder was coming off the wall. Couldn’t find out how to remove this so I literally ripped the whole thing out of the wall and broke the bracket in the process. Cannot even find online this stupid part to replace it doesn’t exist anymore. 🤬🤬

my question is how do you finish the drywall so it looks nice

This is a very good instructional video. I followed the steps in the video to install the drawer. It took me only a few minutes to install it. Before this, installing drawers was always very difficult for me. Thank you very much.

Poor design. Applied pressure and the brackets broke! Will search for a new bar that is not Delta and not quick clip.

Who tf cares about a tiny nearly invisible set screw that is most likely going to only be visible from the floor... Anyhow now that I've vented thanks for the video it might actually help me install this ******** 👍

Yeah I don’t think it’s necessary. On a competitor company video it only shows the two screws that connect directly to the stud being used. However those two screws are lined up.

Just got replacement bracket to replace one w a broken foot. Ive had trouble. I do appreciate the part, but frustrating, very hard to lift over lip on top of bracket. The comment about lubing the spring might help. If at first you dont succeed...🤪

Cool

But how do you take them off 🤦🏻

where is the instruction for the door Knobs?

This is one of the worst ways to install these slides. Look at other videos that are live action.

When does he install it??

Not very happy with these. The instructions, forget it.

…now close the door. Don’t be shy. Show us

How do you securely fasten the third wood screw going into nothing but drywall? Seems like it’s just there for looks lol

Horrible engineering!!

You might want to install the shower first!!😂??

Looks like you can see the anchor sleeve behind the cover. Not very professional.

M

OMG thanks for this video. I couldnt get one side of an existing towel bar to latch on. It kept falling off the wall. Fixed in 2 seconds!!! Thank you! 👍

Terrible design with predictably bad results. Hanging anything on a wall requires screws to keep it in place against the torque that will be placed on it daily. "Quick-click" equals "Delta is offering a more cheaply made product for the same price." 6 months later I'm replacing my Delta towel ring with a competitor"s product that actually screws into the wall. After I repair the holes in my bathroom wall caused by "Quick-click" working its way out of the wall.

Buy these only if you're a masochist. 🤬

I just bought the templates from Home Depot with tax $12.11 cents here in California. I’m going to finish the cabinets fast

five sixty four inches, does anyone hear how RIDICULOUS this sounds ?

Doesn't seem to let you mount the pulls higher than the template allows which appears to be too low.

Good video, shows the general process. However, make sure that you keep the cabinet door open when drilling, else you could drill into the cabinet where the door's mating surface shuts.

this is one the best technical video on how to install drawer slider...thumbs up. thank you very much.. now i will instal the slider on my daughter's cabinet..

There is an error in the video... At 1:09 the narrator has you measure from the bottom of the cabinet to the top of the flared end of the cabinet member.. At 1:28 of the video shows the other cabinet member being installed at X but not at the top of the flared end, but at the top of the cabinet member below the flared end.. Measure X at the top of the narrow edge of the cabinet member not the top of the flared end... Just be careful what you measure..

Great tutorial, saved me time and effort by following right along

Really helpful thank u

What about drawers?

Goated

Bro I am fucking losing it trying to figure out how drawers work lmfaoooo god help me

Is there anyway to remove it It did not stay firm in place How do you get it off

Hollow wall in a moisture filled environment, with your body weight needing to rely on this life line? If you don't stud back this wall you risk tearing out the intallation when a sudden pull is exerted against the point of anchor. Either internal or external anchorage is most advised in the form of composite ,wood or,steel . I'm not talking red heads (butterfly bolts) in sheetrock and tile this is asking for trouble, only full on backing will be safe !!

This is a very poor design. You have to cut down your cabinet drawer by 2" in overall length in order to use this system. I have chosen not to cut my cabinet drawers down. These 94 hundred series Liberty slides and D806 socket set are destine for the recycle bend!

The anchors I have came with a countersunk screw but you are showing using a bolt. What is the magic way to remove the screw that is supplied with anchor ? ANY ideas ?

Pretty straight forward

I'm having trouble sliding the drawer in because the wheels to the drawer slide bump into the wheel on the cabinet... does anyone have an idea how to have it work?

Can’t find the studs behind ceramic!!!

Trying to install the towel bar and toilet paper holder with this hardware has been one of the worst experiences of my life and I have watched family member die from terminal illness and I watched my first born have to be rushed to the NICU after she was born.

I’m definitely in the minority here but I found the installation to be very simple and both my towel bar and hook have been sturdy for 5 years. My issue is how the heck to you remove the anchor from the wall?

Thank you for your video. Do you or someone know How do we fix the toilet paper holder that flips up to open on only one side and the mini allen screws don't stay in because of the rubber or plastic broken that makes it flip up smoothly when it is time to change the role?

This is a waaay harder way to install... easier to do the cab member first and leaving the slides in. Then just make sure each side is individually leveled (doesnt have to be level to each other to function) and then attach drawer to the slides 1 screw at a time, boom. Works so much faster and no silly math needed.