@quail farm That's dodggy and ultra dangerous!!!! You should crimp forked terminals, just like thermal cuple has... That's rly bad make connection with bare stranded wirel, because tak makes poor/resisitvie connection and under heavy load, wire may get warm and overheat...

Hi, why your lamp is off when you turn on the pid and switched off when you get the temperature? Shouldn't be the opposite way?

Can I have user manual for this controller in your video?

Dear Sir, Let me know ReX model and sensor type.

Where are you located? Very clever information on your channel.. ❤

Thank you. Excellent recipe. I used half avocado 🥑 and half olive oil and it worked wonderfully!

They are available on Ebay. And shes using upside down and should be the fat round end where the air pocket is.

what are they eating? can you please tell me? 0:07

I can't enter the initial settings even if I hold the set key together with the shitf key for 3 seconds.. What could be the problem?plz help

Nice

“Well you know,for the shit”😂😂😂😂

Give a solution

Sv- blink at

france quaik

good day sir do you have diagram wiring omron e5cn-q2h03t-flk with solid state relay for my incubator?

I love our accent!

good day sir do you have diagram wiring omron e5cn-q2h03t-flk with solid state relay for my incubator

Hi I already have c100 PID . How can I set tempreature 36.7 . I couldn't find way at the manual to do that . Its always give 36 or 37 never work with me to add dismal

Is the flickering light normal? Is it supposed to be solidly lit?

hi can you say me what parameters are on menu set+up buttoms after 3 seconds?

Would have been so much nicer with out the music.

Good job

like it.

what sensor model is used?

Prezado companheiro, boa tarde, tudo bem? como faço para controlar a taxa de aquecimento do Rex C100 , preciso aquecer a 190 °C , pois vejo que o aquecimento e muito rápido, gostaria de reduzir essa taxa pela metade , isso é possível?

So, what controls ssr here if you connect both out wires to the net as input to controller? This will be short circuit directly to the electric source

Wow! Way too small.20-30 in that small cage.The normal is 1 sq ft for each bird.Stress factor is off the chart with being so confined.Sad,really......

STC-1000 vs RC-113M, which is the best controller for incubator kzbin.info/www/bejne/iJKwoKKam62Hbrs

hi i would to thank you for sharing those videos , i just wanna enter in direct contact with you in wtsp just to ask you special question in this work , tell me if i don't disturb you for sure !

Wow 400more quails

Plucking??

Wow, great narration!

nice video it will help me now to fix my own pid controller on my powder coating oven.

Stop Eating Quail Birds , beware of GODS

Extremely ugly music has been given the end of clip😡.

Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles

Gudday sir. How about i will use for cooling sir, all i need is 16-17 C means, 16C below it will turn-off and if 17C up it will turn-on. I will use as a switch(i will pluge my refrigerator) for restoring my pig semen. Thank u and God bles

thanks !

in germany it`s not allowed to connect PE with N. Also RCD dont like it.

If you move 8 inches to the left there is light so we can see what is going on.

No blue fou relay ! Blue = neutral only !

Have you any idea how inaccurate the temperature measuring is with this product? Tin melts at 449,42 °F....and according to the BERM REX C-100 the temperature was at 298.4 °F when it did....some tolerance, huh?

🤣🤣🤣🤣🤣

LMAO no really keep it frozen and not warm and rotton?

Hi, I'm using the same setup to control the temperature of a smoker. But for some reason the fan permanently stops at the set temperature. But it doesn't switch on automatically when it goes below the set temperature. Any idea what I'm doing wrong? Also if I try to reconnect the output cable from the relay it will start to switch on the fan again. Any help please

Thank you very much for the interesting video. I add one more detail so the chickens don't waste feed kzbin.info/www/bejne/o3uyfGyKa5aCm7M

Can you send me data's to program Rec c 100 for chicken hatchery. Thermocouple is K model 0-400Centigrade 2) How to amend overscale and underscale to Rec c 100.

Do you use the whole eggs or just the yolk like they do with chickens?

kzbin.info/www/bejne/e6CcmZ-bor6YbNU

Hey I am having problems setting up my electric kiln, can someone help me out please, I am using REXC100 PID, 2500W heating element, SSR 40 0-32DCV and a LED transformer 20-40DCV....it gets going for a few minutes but then the heating elements stop heating can someone help me please my email is [email protected]