Just to be sure I'm understanding this correctly, the bottom line after that long multi-part lecture is that if we just want a quick and easy way to check for stability, we can implement Ohtomo's method with WS probes? All that stuff about NDF and Driving point admittance, etc, etc, etc is not necessary?

Does the current version support GPU acceleration of simulations please?

How can I determine the starting and ending points of VGS ?

Why need ZHO on the block diagram of the system ?? I guess that zoh can recognize the pattern been input

Schematic pallete not showing

Can this method be used to measure the center frequency of a PA at 24GHz?

What will be the max frequency of the S-Parameter model if the Nyquist is 20GHz. Should it be 3 times the Nyquist (60 GHz) or 5 times the Nyquist (100 GHz)?

It’s a shame for Keysight to post a video with such low audio quality. I think presenter’s poor english has made this worse

How to download this PDK from video？

Im not understad, but what i should do in NDF method, when i cannot turn off gm?

at the multipole pole selection slide, why are the caps values not matching the rule Cdecp2=Lcdecap1/ Rtarget^2 etc

Hello, can you please suggest how I can run optimization in schematic via command line? - At present my simulation is running in the command line, and separately I am able to run Optimization and Goal Setting in ADS schematic. - However, even though the netlist with Optimization runs in command line, the values are not updated in the design. In the schematic also, they are updated only after I click "Update Design" in the GUI. - I want to automatically update the design in the command line itself once the optimization runs there. Please help in this regard.

this 125mohm how can it implemented in real life scenario ? the VRM & PDN & Load must have this value to keep voltage in it's range, but how with having certain VRM with a certain PCB Layout and a fixed IC as a load ? I am assuming the values chosen above were based on a real characterization of the system, how after this characterization to have 125mohm impedance and neglect all these values ?

Thank you so much for share this seminar on YT, this helped me a lot

Thanks you very much，and where could i access the Design files？

How much EDA cost Sir..

Daisha Plaza

Schaefer Common

❤️🌹

Lauren Mall

Please provide a reference (in Keysight on ytube or elsewhere) for "design centering". Thanks.

This entire approach fails if parameter changes cause nonlinear changes in the performance metric being analyzed. i.e. oscillation at frequencies, esp. if dependent on OTHER parameter values (confounding effect), or a spatial resonant contribution like odd quarter-wave reflections. This issue can be detected if single parameters are swept first, all else constant. But there's no guarantee (in the case where interaction is the culprit). A famous cpu mfr found this out the hard way when spreading DOE far & wide beyond wafers.

Hey! I am trying to learn ADS basics. If you guys know more informative source , please feel free to share with me! (Thanks for this videos)

Hello! I'm trying to learn ADS basics. This playlist awasome but I need more informative youtube channels. If you know any good videos please feel free to share with me! (Thanks a lot for this playlist)

To interact with a neutrino one must first understand its phases, and its charges of said phases, and how neutrons interact with each other via said phases due to any neutrino is a reaction system of phase emission cycles, all facts ,problem is there are millions of ways to harm human race use those energies to build instrumentation to help human race to understand its place in this dimension and grandchildrens future here in ,just ideas is all

Where is the empro_basic library to be found?

Dear Engr. Thank you for such an incredibly educational video. I need assistance with my unit cell design in HFSS for RF energy harvesting. I want to co-simulate the rectifier for the unit cell in both ADS and HFSS to evaluate the energy harvesting efficiency. Could you please guide me on how to do this? I would greatly appreciate your help.

hello, thanks for the video. Can you show me how to import txt or csv file in ADS? I want to plot my measurement data directly and compare with my circuit simulation done in ADS. And be able to see if the tuning fit my measurement datas. Best regards

You're talking about waves and spheres. Not one place on the web that puts those together with rhumb lines. You see that, right? We doing something wrong?

The explanation is too fast, and the pronunciation is difficult to understand.

Also, how do define the port? can we select all pin in the PCB as port for the extraction? or just input and output pin?

Hello thanks for the video, after running the simulation what are the following step to verify extraction is good?

Thanks for this video Do you have online tutorial for PEPRO user?

Great video. Thanks for sharing.

Could you share the ADS simulation file please?

I use N904B which support 2 Hz to 110 GHz, can downconverter be omitted?

Hello! When I plot output harmonics for this particular simulation. It only shows fundamental

Chinglish

is the H transfer function and S21 dB result same? if we perform on the same circuit?

Iyi

I have a few questions. Is there a way to contact you?

Where can we find this example project?

What is the value of Vp and Ip?

请问这里的Vp和Ip是多少啊，怎么计算峰值

i could not download it for trial. what I can do ?

thank you very much

I am not able to generate a new schematic. Those options are seem to be disabled(shown in Grey). What can be the possible reason and how to overcome it?

kemet电容怎么在ADS中正确导入

ADS got rid of the S1P making it impossible to view my antenna measurements. Maddening!

Hello, first of all, thanks. On the other hand, I have a doubt, what is the main difference between a symbol and a hierarchy design?. Regards.