I have one of these, about 50hrs, grandpa bought it new. I even have the original manual, warranty card, bag with prop pins and extra prop. It needs a new impeller and the gas tank has a pinhole somewhere, dad had it hanging on his boat as reserve for years. I had it running a couple of years ago, started easy.

its so great to have a guy that sloweleys explains everything

Hi , I have the same question as Loreeta what company did you purchase the 8 ft. bimini from. Thanks

absolutely love the build great whaler! im currently restoring a 1989 13 super sport. what brand is the Bimini top? been trying to find one with more coverage

Estou precisando de uma boia desta carburador. Alguém pode me dizer se é possível encontar. O material da mesma e cortiça. Obrigado Milson .'.

You could have soldered a piece of brass on there and made new threads. I'd do that instead of JB weld (this stuff ain't good for much IMO).

Yeah, mine had the same problem. As I had to replace the cord anyway I just hit it all with brake cleaner. It dissolved all the old grease. Then it got just a little spray grease and a new cord. It behaves like brand new. :) Grease degrades over time and decades of sitting in a shed didn't do me any favors.

I just got one. In near mint condition (a little dent in the tank). I can't wait to take it apart and get it running again. :) Thanks for sharing this playlist with us.

Hey Leo. Thanks for this series. Just the ticket. I have my stepfather's 1963 unit, which looks identical. He bought it new and used it sparingly as a fishing kicker on his runabout. It has not run in 20 years, but I am going to do the overhaul so I can use it on our dingy when we go sailing/cruising. So much better than rowing, specially when the wind kicks up. Keep on with the good videos.

That is a beautiful job. Top notch.

Just inherited one of these and I need to get it running. Cant wait to watch and learn!

Can you remember the part number for Carburetor rebuild kit for Johnson 40EL75 and where I can oder one

I have a 1985 Johnson 40 hp with out starter that looks identical to that 40 horse Evinrude , single carburetor with controls on the right side of the carburetor. Yours is the first one I have seen like it.

I just recently bought that same outboard! Was wondering if you had a link to be able to order parts for it?

Good content mate, where did you get all the parts for this motor? Cheers

Thanks for your walkthrough. I’m in the middle of restoring a 69’ …question. I can’t tell where your trolling motor is plugged in. Do you use the mkr-28 minnkota plug? Thanks

to bad marinengine only send in USA not worldwide

Hey Leo great videos, I just got the same motor and am just wondering what oil to use in the lower gear case??

Looks awesome. I finally finished my 13 whaler a few months ago. Finally got a good running engine. 2009 50 mercury 2 stroke , it will have to last long enough for me to save up for a new 4 stroke

I may have missed something, but how much does this weigh? i was thinking of putting one a canoe!

Steve do u have any experience with 1958 Lake crafts?

I have the same motor. My motor when I put it in head and turn throttle quarter of a turn it sounds right but when I turn to full throttle it just stay at the same quarter turn speed it don’t rev up or nothing. Wondering if you could help me figure out the problem. Thanks

I have a 72 model 40 evinrude norseman anyway I can see the carb linkage set up as mine is missing and have no clue what to get to replace it. Thanks

Where did you get the center console

What's the length of the decal?

Really nice!

@Leo Gallant I know the Aphrodite project is 10 Years old, but I wonder if you recall if there were any challenges or concerns when removing, or while having the toerails removed?

This rubrail install is helpful. I was trying to figure it out reading the instructions but needed visuals. Hoping I dont screw the installation up 🤞🏽

My 1962 3hp. works best with the highspeed needle open 3/4 turn and the idle at 3 turns. When engine starts set both for best running, THEN install the adjustment knobs to between the 3 & 3 positions. If reusing the cork float boil off the shellack coating, dry for a few days, maybe a week, in a dry area of your workstation and coat with a thin coating of epoxy. I use 40ml. of a good grade of 2 cycle outboard oil per liter of idealy non ethenoled 87 0ctane regular petrol.

Como reemplazar selenoide de embrague de transmisión

I have the same motor and it don't really run with alot of power, I was wondering what that knob is with the red flat thing on the end to the left of the choke, where should it be on start up and where should it be after its running

Hi sir ! I got the same motor, model jwl19. I need to take out the big screw under the starter to access under it. The motor won't start and we have no sparkles at the spark plug, we're guessing that the ignition coil are at fault. If you can help me and give tips and would really appreciate man! Thanks anyway and nice restoration!

Glad to see you finished your whaler. My 66 is done as well , haven’t had much time to splash her due to floridas crap weather lol. I posted a few videos on my channel , I’ve done so much to mine it’s looking like a brand new boat. One thing I’d suggest you do is upgrade to bigger tires !! I had those little tires on mine and it seemed that every time I go out to work on the busy the tires were super low .. put the big tires on and haven’t had any issues.

The center console mounts? what material are they, and how are they attached?

My start rope broke also to sharp metal close to knot hole. And rope&knot pieces was inside/under freewheel. And preventing starting. Starter is ok. Took off freewheel with cheap 2 leg puller. Then found 4 cm pieces of starter rope. I have many starters and I will compare if all starters have sharp metal edge cutting rope ( next to knot ) like sharp blade.

Great vid. Damn!! Those rails are rigid!!

I enjoyed your video master, thanks for sharing as always 🙏👍

👍👍👍👍👍👍👍 🌺🌺🌺🌺🌺🌺🌺 🙏🙏🙏🙏🙏🙏🙏🙏 Selamat pagi kawan ku, video anda sangat bagus kawan ku, semoga harimu menyenangkan kawan ku, Tetap semangat..

i love you boat

Well done

Looks great!! 😘

Здравствуйте, смотрю ваш канал про лодочный мотор Джонсон 3hp. НЕ МОГЛИ БЫ ВЫ СДЕЛАТЬ СУБТИТРЫ НА РУССКОМ ЯЗЫКЕ??? НЕ ВОЗМОЖНО СМОТРЕТЬ ЕСЛИ ТЫ РУССКИЙ!!!

Worst video ive ever seen not informative at all

This guy has no clue. When these motors are adjusted correctly they run fast and idle extremally low and smooth as a Kitchen Aid Blender . Get a Manual!!! some training and some talent.

Do you have a link for rub rail where to buy it ? Thanks

Curious how its held up after 9 years

hello there I am a new subscriber I watch all the video for your build I was just wondering where do you but all the parts from I have the same engine and would like to get same parts them you bought please let me know thank you

I personally would have taken the time to fix that transom properly. The transom has a lot of pressure of the thrust and with that a the pounding and vibration I would be nervous as heck.

where did youu get the console?

Looks great!!