Traci is a beast ❤❤❤❤

Very helpful I needed these tips before I do it on mine. Your video is the only one I found that actually explains the process

The secret was no cameras everywhere….

I can barely move it, I'm on the end of a 24" breaker bar. This is going to take a while.

Thank you for the great camera work!

Where have you been

My oil pressure sensor is stock on 80 in my 2007 Silverado. As I am driving on the road, suddenly it slows down and the engine light turns on and stays driving more slowly for a while. Could this be another sign that I should change it? I will change it tomorrow but I wanted to know if it could be something else to be changed. I have 176K miles. Thank you.

Yes 327 5.4 liter 4.000 in bore 3.250 stroke not LS 325 5.3 liter 3.780 in bore 3.622 stroke

Fixing nascar -Get rid of France Family -put both races back in Rockingham. -Drop pit road speed limit -put 5 regular lug nuts on the wheels -Do away with stages -Drop Kansas, Loudon, Chicago -Put 2 races back in Wilkesboro. THAT WOULD BE A GOOD START.

Thanks for the video, my 05 was at 80 now after changing the sensor it's pegged completely out past the oil can symbol on the guage, can you help with what be wrong? Thanks David

My master cylinder is similar to yours. I had brake fluid leaking from where the reservoir cap meets the master cylinder...only a few drops every now and then... The brakes dont feel spongy so Im guessing no air in my brake lines...just dont seem to understand why I have these leaks occuring?

I think the first thing you do is check the dip stick oil level.

Where did all that metal go? You may be doing main bearings next.

Great video, you're a great mechanic!

Thank You, Man!! 👊👊👊

I was getting the same code p1345 and also a code for the crankshaft p0339 found oil leak was causing the connector to be soaked possibly contaminated cleaned it with electrical cleaner and put some dielectric grease took care of the issues and both codes.

not too many other videos (none to my immediate knowledge) showed the up close on the sensor prior too taking it out 👍🏾

on my D4d when I push in the clutch handle I get no movement of the brake shoe on the drum. I can send you video because I'm stumped as to what adjuster I need to allow of contact to the drum. The spring is set to 3.4 inches and I can rotate the drum but pushing the clutch forward does nothing. Any help would be apprechiated. Cat_bruce

I have this issue its at -27 so which way did you move the distributor cw or ccw when you moved it a tooth? Thanks

Great video. How do I figure out which mount is broken. Also, did the front mount just slide out or did you use a pry bar

Great video. How do I figure out which mount is broken. Also, did the front mount just slide out or did you use a pry bar

I have the same issue on my 2019 4.3 i already change the sensor twice, the first time was with a sensor from autozone and second time was a factory sensor (ac delco) and the issue Didn’t get resolved. The truck runs fine and there are no weird noises coming from the engine, I’ve put the scanner on it and it says oil pressure switch. Would you have any idea of anything else that might be going on with it. TIA

I got one cat D 6 B 1964 it was gas powered start pony moter but went and direct strat put on strater moter and Two batteries goes well I use it all year two trees lots and hill gorse and under runners bank the push off got case 770 disc I pull

I got one cat D 6 B 1964 it was gas powered start pony moter but went and direct strat put on strater moter and Two batteries goes well I use it all year two trees lots and hill gorse and under runners bank the push off got case 770 disc I pull

Had same issue on my ‘11 Tahoe LTZ. Probably had 1/2 as much room to work as you did. Not a mechanic, but I got mine swapped out in about 2hrs (inexperience and lack of tools). Worst part was laying over the engine to get back there. Gotta love the engineers.

My respects to you sir. I need to do this to my 2006 escalade 6.0. Just started getting a low oil pressure warning and my oil pressure gauge going from 0-80 randomly. Thank you sir.

Great story!

I was at that race sitting about 20 rows up at the start/finish line. Had a great view of this. That is a great race to go to as it decides the final four in the chase going into Phoenix and tempers flare.

If you going to do a video sir, you need to learn how to hold the camera straight and give good instruction and dictating because what you're doing is son. You're rocking the camera you really can't see s*** so use a s***** cameraman

Thanks man

I have this exact car and was just told I need new motor mounts, how many are on the car? I just got new cv front axels and was told the motor mounts are also contributing to the noise I hear

Great video thanks this is what I need done on mine. If I run it for a little while it won't hurt anything correct? Just the annoying gauge needle

Thanks brodder🤙🏿🫡💯

My gauge is dropping slowly below the safe area. Engine runs great oil is new and full.

Fantastic! Liked and subscribed! Thank you very much!

I remember a story my grandpa and Dad would tell about an alligator that Smokey had. I believe that it was named Albert

Great video. Great demonstration and very helpful info. Thanks for making and posting 👍

How can you not love Ronnie Thomas?Kind,smart,funny and comfortable in his skin.Need more Ronnies and less Bubbas

Ronnie Thomas has to be one of the nicest drivers ever in NASCAR. What a great man.

If my tractor has a 12 Volt coil that says on it "No external Resistor" does it start and run on 12 volts? My points have not burned up and my tractor is just like yours. The wire coming into the coil measures 12 Volts.

What kind of computer or info tool do you need to reset this cam crank collation adjustment

Do I need to install the filter of just the sensor by its self ?

I have a 1994 GMC Sierra and I was told that the older truck runs on high oil pressure readings. I installed a new oil pressure sensor and now my readings is around 40-60 , do I have to tighten it some more are what am I supposed to do? Thanks

This is funny seeing this clip. My daddy told me his whole life the production company bought out their cars for this move. (The were stock car racers on dirt track) they bought 6 cars for this movie. And him and his crew never got credit for one thing. Every time I watched this movie with my daddy. He goes there’s another one of our cars. All I’m saying is they didn’t get credit for this movie. Love every minute of it. But just wished my daddy and his crew got credits for it.

Lmao 😂😂 keep your critical race theory to yourself 😂

Unfortunately my DeWalt 1/2" impact wrench would not loosen the pinion nut!

This is my favorite movie of all time we miss you Kenny lots of love to the whole cast this movie was so amazing in the day I’ll never forget them days

That dw impression lol

Good video.