Hey, can u give me the exact model number for this bulb since there are way too many bulbs on your website! Another thing is how do the high beam work with only the positive and negative terminal connected

So can i install these philips h11 ultinon led on 2014 dodge charger for some reason they flicker but i thiught it had the right connector and stuff

Also known as nineo. These are the same quality contruction with external driver as the S-V.4 on headlight revolution. Just $205 a pair. I’d rather spend much $200 or $150 less than from HR. If it’s the same led bulb.

Would this work with turn signal as well?

This is not for 2021 and up years like hybrid models

Thank you very much for the detailed instructions on how to install these LED light replacements. I ran into an issue though, I took a picture before the fog lights at the bottom were working, now that I installed the new LED lights the fog lights no longer turn on? Any suggestions? Thank you!

Man, I really appreciate this video. I’m bout to go get my LED lights right now.

Are these 9005/9006 or H11?

The backup lights on my 22 lasted 25k miles from the factory. Thought that was a little low tbh, considering they are rarely used for short periods of time.

Why is there a square block with a cable leading to the light? What is that box for? Because I've seen lights specifically for the bmw e90 without it, so does it have a purpose, or is this just the old solution back then?

Definitely don't use t-taps, solder it.

Thank you! Your video is very helpful.😊

Please indicate the model of LED bulbs that I must buy If I want to use them without ballast previously used for D3S.

Thank you. Thank you for this video! Very helpful!

Where do I purchase the replacement LED bulb to put in a 2022 Toyota Corolla?

3:08 this part you lost me 😂

I had some LED’s that seemed like they were messed up and were too bright in low beam. I figured it out with this video!

LMAO!! "The chunk...." smh

I just wanted to comment how there were steps in this video that were 100% unnecessary and just wanted to follow up with the trend in the comment section because it's true that whole peeling back the fender liner was unnecessary completely

i accidentally unscrewed a smaller black circle piece to the top right side. has no light attached just a ball on the bottom. is that 0:15 important to put back on. i couldn't get it screwed back on

Stop light bulb

Ty

What's the name of the led light bulb ur using and the part that hooks up to the led bulb that u spliced to the cable running to the ballastro

Coupd u answer a question for me, my prius headlight need this how do i go about getting the parts i have no clue wht the names of them are atleast the ones that would fit

Hi mate ! I owned one Colorado 2.8 LTZ yr 2013 recently, but one thing make me unhappy was that projector lamp getting dimmed and it seem like it hard to replace it with the H1 bulb. At the the driver side, the air cleaner box block the space and same at the other side which is very limited space to replace it. Anyone have idea or tips how to change bulb easily might share the experience...appreciate it..

The tape is a secret step that I’ve used on several of my vehicles. A real helpful tip. Also, I changed my 2022 Chevy Spark’s map light over to a red LED. Easy on the eyes at night.

This isn't for a 2016 Sentra, pull ur thumb outta ur ass

do you need any special load resistor kits? I know that on a 2013 honda crv you need the H4 LEDs and that they have both low beam and high beam, but also, one of those also function as the DRLs. Will any H4 LEDs work, or do you need one with special ballast or non-polarity, or something?

The vehicle in the video is not a Gen3 Prius (2010-2015), which has very tight space for bulb replacement on front passenger side. Better to include the vehicle's model year in your video so that it does not mislead.

Thank you so much for this! Just changed mine

How the heck do you rotate the damn thing to lock in place

Ugh tried just to pull out the wire connector from the board but it won't just pull straight out like in the video. Any tips???

Not exactly the headlight spot since it’s one more to the right, but helped give me enough of a hint. Jeeps engine compartments are a bit crammed, so you get used to trying to squeeze into tight spaces. Thanks for the video!

There wasn’t a lot of room to re-attach the clamps, but your video helped a lot! Thank you!!!

What size bulb is it???? I’ve bought one and it was a big ass socket one.

T0 check motor of electric windows

This video did help me a lot, thanks!!

Got a video change ing the low beam

That's not even where the bulb is on a 2015 LT1

thank for a good instructional video!

Thanks bro

I know this was 6 years ago. But those led bulsb does lot make 2200 lumens per bulbs They only make 5W, that’s 500 lumens per bulbs Compare to the GTR-Lighting - ultra series T15 led reverse light bulbs. They only make 12W - 1200 lumens each, and those are the real deal and they are the brightest ones. Or Lasfit - T series T15. 13W each, making 1300 lumens each, affective lumens is 750 lumens each. Those are better results.

Cool

thank you very much my led lights were looking everywhere and with this they were good thank you very much

What lED bulb goes for rear turn signal for Toyota Corolla 2024 hybrid LE?

Never buying an Acura unnecessarily difficult for what

I installed led for the high beam but after 15 second stopped working, i searched for fuses and didn't find anything, any help

I have a 21 Malibu with the same tail light design, I removed the assembly thinking I can change the bulb itself because I bought a strobe light bulb & Amazon said that I would fit on my car but no. I’m assuming there’s no way I can get to the bulb itself?

Easier to do the driver's side when you take out the battery. More mobility

Will there be a video or someone showing or explaining to people who have the 2020-2024 Corolla the process of changing the high and low beam front light bulbs?🤔🤔⚠️⚠️