Yellow Birch Farm

Пікірлер

@andrewhildebrandt-vn4or Ай бұрын

What RPM do you run it at? Also where do you see the size of the bale. Just bought an 845 looks the same but cant figure where to see the size as you are baling.

@yellowbirchfarm7794 Ай бұрын

2k-2500 rpm it bales a 4x5 round bale at 2500 rpm it will bog a 75 hp tractor if your not feeding hay into it. if you get to the end of the row with 90% of a bale and let it run it will make the bale tighter and bog the tractor.

@osi2484 7 ай бұрын

Big job. Did this a few yrs ago on my 4010. Glasses on when grinder cutting. Good video

@yellowbirchfarm7794 7 ай бұрын

I normally wear glasses when grinding but this time I didn't have them on.

@harolddotson2155 8 ай бұрын

Give a thousand for mine worth every penny

@yellowbirchfarm7794 8 ай бұрын

they are very easy to run and makes life so much easier ,

@NeilBright 9 ай бұрын

Back up before dumping help on restart shear bolt life

@yellowbirchfarm7794 9 ай бұрын

I've got that part down seems to be a good baler

@NeilBright 9 ай бұрын

Oil all chains before you start and during. Saves chain life old used oil. Stop when it to fill mark. Save bars they break good unit

@yellowbirchfarm7794 9 ай бұрын

i have a oil on the back i open the valves on the way to the field and turn on the baler to oil it and i turn it back on after baling. grease the machine after every use.

@rogercarrico4975 9 ай бұрын

We had a 846 for years and years. Ours was a manual tie. That Auto wrap is sweet. They are a very durable baler for the most part. Of course over many years baling, things will happen. Yours has the single BIG spring that keeps pressure on the bale chamber that make the bale tight. Later they went to a dual spring set up. Ours was a single spring. I can see the adjustment is all the way out on yours. So it's set to make a bale as tight as it can. It's almost impossible to get it to plug up. However in very light, fine stem hay. Is where you might encounter a problem. It has trouble moving the hay from the pick up reel to the floor chains. The floor chain fingers seem to have a problem grabbing very fine hay. If this happens. I've found that throttling back your tractor's RPM, while increasing your ground speed ( gear or 2 higher) helps. The sear pin broken is concerning. You might want to turn it by hand. Before you put power to it. Just see if anything is binding up. Anyway, good luck with you new baler. BTW, My record in one days baling with our 846 was 114 bales. Some really good hybrid Burmuda!

@yellowbirchfarm7794 9 ай бұрын

We have used it on two small fields so far 14 Bales it does a great job but does not make A tight bale or as tight as I would like and yes the auto tie is amazing I have seen a few manual ties at work I see both pros and cons with a manual tie. I have noticed if I get to the end of a wind row and take enough time to get to the next row that bale will go from 75% finished to 50% finished which makes for a tighter bale and makes that 3020 work for it. it had broke the twine and me never running a round baler prior I just laid the twine across the knife and it started tying again. we had a few issues when we started as in the hydraulics has a few small leaks fixed those and the cables to unlock the rear door had to much slack so to raise the door i would have to jump off the tractor and manually release the door kinda dangerous. when we cleaned oiled and greased it just before storing for winter it was running like a sewing machine.

@thecollectoronthecorner7061 9 ай бұрын

new subscriber. We have owned goats in the past. We now have hair sheep.

@yellowbirchfarm7794 9 ай бұрын

we have talked about getting sheep but we have not yet made a move to do so.

@69erdevildog1 10 ай бұрын

I have one of these..had it maybe 8yrs never had any problems..it won't bale a tight bale but it's tuff as nine inch nails

@yellowbirchfarm7794 10 ай бұрын

I baled 14 bales and I noticed if you stop and let it roll before tieing it packs it tighter either way it beats square bales although we do both

@briancs613 Ай бұрын

Check your adjustments on the big springs on the sides. That's how to controll the tightness of the bales.

@bllitzz1 10 ай бұрын

me and my friends struggling in farming sim:

@yellowbirchfarm7794 10 ай бұрын

I've been there

@robbiecampbell2153 10 ай бұрын

Looks like it makes a good bale. Good balers

@yellowbirchfarm7794 10 ай бұрын

It does make a very nice bale with no issues now that I tensioned a few cables

@bllitzz1 10 ай бұрын

@@yellowbirchfarm7794nice!

@AriyanEduHelpline 11 ай бұрын

I hope you are well. I have seen your KZbin channel. Your channel is very good and your content is very nice but your channel needs few updates.

@AriyanEduHelpline 11 ай бұрын

Like you need a professional logo and banner, customization on your channel. I researched your channel and I saw your channel has fewer visitors,subscribers,video likes and views.

@AriyanEduHelpline 11 ай бұрын

I can help you if you want. I will create an attractive logo and banner, customize for your channel, I will SEO the videos of the channel and KZbin advertising through Google Adwords

@AriyanEduHelpline 11 ай бұрын

So that your channel gets subscribers and watch time quickly and channel monetization on Fast.

@AriyanEduHelpline 11 ай бұрын

Iam digital marketing expert. If you want to know the details, I will meet on Google or Zoom Meet at your time.

@yellowbirchfarm7794 9 ай бұрын

Thanks for visiting

@Grimpuh 11 ай бұрын

That machine is a beast!

@robbiecampbell2153 11 ай бұрын

We have a 846 I like it it's a good baler. Simple to operate auto tie they like longer hay and harder to start on short hay tends to plug up. Just make sure to keep plenty oil for your chains

@yellowbirchfarm7794 11 ай бұрын

Thanks for that info not sure if you have seen our cutter it's a 8ft woods bush hog with the removable side discharge it usually cuts 12 to 15 in in length give or take it's not precise