Who is watching this in 2025 with the recent asbestos recall? Would changing the spur gear make you vulnerable?

So there is two o2 sensor. Pre cat is for afr and post cat is just for cat monitor. Seeing it run that lean means both might be bad or other stuff like vac leak. But yea you could blow ur engine from running super lean...

No, it still sounds like crap lol

How long did the charge take?

What happened to the red and black one and the orange one

You can try tightening it and then loosening it... sounds weird but it does work if you dont got a torch and everything else fails. Try tightening it with your impact and then loosening it with the impact. The goal is to break loose the corrosion points.

had mine for a week. those rubber o rings on the center drive shafts pop off every 10 minutes.

So the Slipper Clutch needs loctite! It comes loose QUICK!

I bought a breaker bar and what do ya know it loosened right up!! Super easy with a little more leverage!

Crank it until it breaks, then curse your way to a store, and right when they close realize you broke something else then stare at the floor in a pool of sweat with cuts all over your hands. Finally, ignore any new noises or sensations after 4 days pass following the completion of your job. Worked great for me. And, if my wheel falls off on the highway, I won’t have to worry about it anymore now will I?

This is how the never-ending accumulation of tools begins, gentleman. 🫡

The tire on the deadbolt will make it top heavy

Get a real impact not a Ryobi piece of junk

Go get a can of air duster and turn it upside down and spray the bolt for like 5 seconds and use a wrench to loosen it

Ext breaker pull up not down

You should get one too.

I don't know if it was just me but the first time he was pointing I thought he was pointing at the slider pins. Like others have said use a long breaker bar after turning the wheel to give you better access. Sometimes percussive maintenance helps so use a 3 pound mallet or a heavier hammer and tap the bolts on the head and that can sometimes free the initial friction. Other times put the breaker bar (non-ratcheting) and bounce it on both stops (tightening and loosening) back and forth and that can also help you get it free. It doesn't look corroded enough for you to need heat to get it free but since that area heat cycles with the brakes they like to get hard to take off.

You need to turn the steering wheel and then get a breaker bar on it with a six point socket and you'll be fine

I had to drill a hole then beat it out with a punch then plug it and welded it shut then pulled the plug wad out and cleaned tf out of it

For me nitro has always been my favorite the smell and sounds are great you just have to learn how to tune. Electric has its place and I do have some but I enjoy nitro more.

Harbor freight Hercules 1/2 in or 3/8 impact. You need a lot more torque than the one you have now.

If they spin they pull right out.

pb blaster, turn the wheel right, 36in breaker bar, use your bodyweight. good luck

Turn the wheel all the way to the right. That will give you easier access. Go to your local parts store and grab a map gas torch Heat each bolt and break them loose with a 1/2 breaker bar. The good news is even if the bolts snapyou can buy a new bracket.

A cheap impact doesn’t always say the right torque specs on it. You and try adding more leverage to a breaker bar with a pipe but if not the comment above is right as well hammer it home tell the cows come home might be the way.

17mm wrench and a brass/copper 3lbs hammer. Put the closed end on the bolt and hammer against the curve of the open end. I usually put my free hand over the closed end and hold the wrench, while I hammer. If you don’t have a brass/copper hammer, any hammer will work, as long as the handle isn’t cheap. When my 1600 ft lbs impact can’t take off a bolt and I’m out of Map gas, it’s hammer and wrench time.

The Perfect socket fit is Awesome

I've never changed my spark plugs on my 2005 Avalon 😮

tow strap should be added

Try to trim the original tip a bit

Have you used it outdoors much? I use mine rain or shine

Get street tires and stiffen the suspension that's what I did and I added 10 more mph but if I change the pinion gear I probably would be flying

I think the biggest difference you have made, is the interior. That definitely look much better than when you first got it!

helpful video, thanks man! 😎✌️

Hello guy's! Get a almost new 4x4 vxl and my spur and pinion(13t) sounds kinda loud. Also the velineon engine spins like it have a "step's". Is this okay? Because of it model starts a little bit hard, shaking. Have a old 2wd vxl with older velineon engine and it's spinning smooth (when you spin it with fingers) and spur/pinion is much quitter. Is that okay?

Harbor freight breaker bar life time warranty on hand tools and the jack handle to extend the bar for more leverage

The only "cool" mod are the shifter bushings and the stitched steering wheel. The way the footwell lights were installed look ghetto as fuck though.

hell yea

Oh this is awful. Worst gen civic fantasies

Damn this is epic as hell. You should install the turret and add a mcfarlane chief figure to make it even better.

Great vid as usual brother quick question, what do you think about those michelin cross climate tires? are they excellent on snow compared to winter tires? im just curious thanks bro

Isnt the Mojave alot better?

Change it to a different badge from a different car

Hmmm, something seems oddly familiar 🤣At least the first part if I do say so myself. Though I must say, I think you upped me on the cinematics in the first half 🤔 I think my real strong points were the sound and visuals on the car.

Can you remove the front and rear bumpers on the bronco like you can’t with the 1/10 model?

Get black spray paint that turns rust into primer black background would look nice

I had one of these and absolutely loved it, they can really take some abuse where a cheaper car like a redcat will get torn up and break the first time it rolls over, where the jato just eats it and keeps going!

Great trucks and review! 👍

I just bought myself the exact same car, same colour, same trim, 5spd, shot clear coat, etc; painted my hoot black the day i got it haha Paid only $1000 (740ish usd) for it, basically stole it.

It supposed to stick out a little bit more