Should the crank be able to move side to side a little bit on the bearings? Not the rod I mean the actual weight.
@nojusdomarkas3572Ай бұрын
Im begging someone help, why could my stators keep going bad they get grounded after some time of riding what could be the problem ? It generates a lot of power like 14v at idle, long time ago everything was good but it generated a lot less power at idle
@Voltsmerss2 ай бұрын
Thanx. Wery good video.
@Colormanify4 ай бұрын
👍🏻
@freeenergy4everyone5 ай бұрын
Hi, how can you get the roller bearings out of the casings? I can knock one out but you can't get behind the other one.
@majkutisusernameom6 ай бұрын
How can you put crankshaft on a bearing so easily that's bull@$&7 😅
@Alexanderlfjdjdjdh7 ай бұрын
what oil for oil bath? just regular 10 30?
@Nighty046 ай бұрын
Nah 10w40
@MrTrevorroe8 ай бұрын
Best am6 engine build i have seen today, thank you, it helped me loads, great job bro 👍🏼 👏
@windkracht1053 Жыл бұрын
where did you buy your Bearings
@roo8901 Жыл бұрын
Doesn't matter where you buy, just try to buy bearings that are made in Japan or the US
@geertkoornneef8325 Жыл бұрын
You forgot a shim on the kickstart
@bartsshorts Жыл бұрын
is it possible to block the water pump and get a air cooled cylinder for it?
@roo8901 Жыл бұрын
I think it's not possible and even if it was it would not be such a good idea. Just swap a suzuki pv engine if you want air cooled.
@KamranIbrahim-m7x Жыл бұрын
How do you remove the smaller selector shaft
@frostyvenom6484 Жыл бұрын
Having a problem with my clutch no matter how many times i adjust the pressure plate and cable the bike stays in gear wit the clutch lever out or in. I have assembled everything correctly but my issue is the clutch is not engaging
@audi0syst3m62 Жыл бұрын
i took apart my am6 3 times cause i can't shift it... i can't figure out why. tryed everything but the gearshiftlevershaft can't rotate the gear shifting drum... i can shift the drum with my hand through all 6 gears but if i put on the shiftlevershaft and the other block half... it didn't work... tryed to swap the shims on the output shaft but that didn't worked either...
@roo8901 Жыл бұрын
Do you have the spring and the metal ball under the gear shift drum?
@audi0syst3m62 Жыл бұрын
@@roo8901 yes :/
@roo8901 Жыл бұрын
That's weird then. If you can shift gears while the engine is apart and not when the other block is assembled, then the only reason I can think of is that there is a wrong kind of shim and the system becomes too tight to turn when the other block is assembled. I cannot think other reasons if all the parts are okay with no damage in them :/
@audi0syst3m62 Жыл бұрын
@@roo8901 I’ve got a shim under the shifting drum, I removed it and now it looks like that was the issue I will test it tomorrow 🙌🏼
@roo8901 Жыл бұрын
Yea, that would explain it because there's not supposed to be a shim under the drum, only on top of it. The gear shift lever on the other hand has 2 shims.
@azuolasmk3510 Жыл бұрын
What if balance shaft and crankshaft gear dots do not match? I took of the clutch cover of my engine and they are not alligned. 7:20
@pascalvandertogt Жыл бұрын
it will prob shake your ass off when you start your moped they are supposed to be aligned
@roo8901 Жыл бұрын
It can and will damage the engine after some use.
@finleypenaluna149 Жыл бұрын
How do I get a stuck short rod ouf the clutch
@roo8901 Жыл бұрын
How is it stuck?
@justus480 Жыл бұрын
Mihi trainsurffaus videot on hävinny
@tiitustepponen9849 Жыл бұрын
ihmettelenki ku nimi oli jotenki tuttu mut joo täähä oli se surffaus jätkä
@eetu4120 Жыл бұрын
mihi surfing videot katos
@tecrigfx Жыл бұрын
mitä videoille tapahtu
@SalkkaritHistoriaa Жыл бұрын
minne katos train surfaus videot?
@Zakkeuss Жыл бұрын
Tää
@alberto14ro952 жыл бұрын
2:23 what is that blue glue called?
@roo89012 жыл бұрын
That wasn't as good sealant as some other products that I've later used so I don't recommend that, but just look for some silicon sealant that can withstand high temperatures and is designed for engines - I recommend the Würth Silicon Spezial -sealant.
@alberto14ro952 жыл бұрын
@@roo8901 Thank you very much!
@forwards32142 жыл бұрын
so only shim on top of the geartumbler and gearshaft? i have an 2017 am6 and i bought a new shim set cus i thought i missed a lot of the shims and when i assembled the engine again the gearbox was locked up :// so only those shims u showed is all that is needed?
@roo89012 жыл бұрын
They should be all you need, one shim on the gear drum, two shims on the gear shifter - one on both ends.
@arturalmeida96772 жыл бұрын
Cerco pistone diametro 47,5mm e piolo 13mm per motore Fantic. Sarei grato per l'aiuto
@juanrengelserrano30902 жыл бұрын
Y la arandela de el eje secundario en el rodamiento de agujas no la pones??? Esta mal montado el motor literalmente no has puesto ninguna arandela solamente la de el tambor
@roo89012 жыл бұрын
The newer minarelli am6 model has "built in" washers in the input shaft and the drive shaft, the am6 engines before 2010 have additional washers that you have to remember.
@juanrengelserrano30902 жыл бұрын
@@roo8901 look videos of lf racing one of te Best mecánics in spain
@svensildelid77642 жыл бұрын
Gir is føkt
@svensildelid77642 жыл бұрын
You av Don wrong is not working
@orlandopinto37192 жыл бұрын
Boa noite porque o meu metor deita óleo por o respiro quando está quente
@rollmc56012 жыл бұрын
can someone tell me why mine wont shift gears
@roo89012 жыл бұрын
Probably missing some shim(s) in the transmission if you've built the engine. If not, then it can be that your gearshift axle's "teeth" are broken and it cannot turn the gear drum.
@rollmc56012 жыл бұрын
I will check that tomorrow,thanks.
@alanssnack11922 жыл бұрын
does the am6 have a harmonic balancer? a. = yes does the derbi motor have one?
@roo89012 жыл бұрын
I don't know about the derbi motor so much but I bet that it too has.
@-recoilbear-25762 жыл бұрын
no it doesnt but in my opinion their engines are better
@korez74498 ай бұрын
Only the derbi gpr engine
@jagodic67962 жыл бұрын
looks impressive. would be enough space to lay there as a slim person?
@dansjansons66062 жыл бұрын
Ahh shit i dont have the ball for clutch
@roo89012 жыл бұрын
Yea, it's needed for the clutch to work
@sveinoveutvik43983 жыл бұрын
also, when i pull the kick-starter slow the piston does not move much, only when I pull it harder does it move. Is that normal? And if someone want to help me more, watercoolant leaked down to the crankhouse (?) under the cylinder head. Do i need a full disasembly, or is it ok to just loosen some nuts and let the coolant drain out? Nothing in the oil.
@roo89013 жыл бұрын
If the coolant leaks to the crankhouse you might have missed a seal. Check that you have all the cylinder seals and that the paper seals are not ripped...
@sveinoveutvik43983 жыл бұрын
When you put back the cylinder there is a gasket with one round hole for the water-coolant and one rectangular at the side of it. What is this for? i see the gasket has hole for it, but MY cylinder does not have anything there. Do i have the wrong cylinder?
@roo89013 жыл бұрын
If your cylinder does not have the hole it's not the right cylinder there.
@l81x162 жыл бұрын
no the square hole does nothing i thought the same , the round hole is for coolant
@unbegrenzttv39593 жыл бұрын
Hey your Video is awsome. After I build the transmition one big shim left over... where it has to go?
@roo89013 жыл бұрын
If you have an older am6 engine the big shim can go in either end of the output axle. Google a exploded view of minarelli's transmission and look there.
@unbegrenzttv39593 жыл бұрын
@@roo8901 I got it thanks a lot
@oce73043 жыл бұрын
man you're a life saver
@adriansmr.70 Жыл бұрын
Same
@yeetz2958 Жыл бұрын
same
@malteboye16493 жыл бұрын
Can u explain to me how the neutral switch works for me, mine doesn't and when I look there is just metal in the hole?
@roo89013 жыл бұрын
Is your gear drum original part or aftermarket part?
@malteboye16493 жыл бұрын
@@roo8901 not sure
@roo89013 жыл бұрын
If there's no hole for the neutral gear, buy a new one and check that it's fine
@malteboye16493 жыл бұрын
@@roo8901 i think it's me being unclear, but just the neutral indicator doesn't work, don't have the gearbox open.
@roo89013 жыл бұрын
So you can get the bike on neutral gear? Because if you can and the indicator light doesn't show up then it's the neutral gear sensor wire that is not attached to its screw.
@fanitram3 жыл бұрын
how do I fasten the clutch cable on this?
@roo89013 жыл бұрын
Screw the clutch adjustment screw that's at the clutch lever all the way in and then you have to push the clutch rod on the engine and at the same time put the cable to it's place. It's quite a tricky thing to do.
@fanitram3 жыл бұрын
@@roo8901 thanks, it in place on the lever but struggle with other end
@roo89013 жыл бұрын
Yea the other end is annoying to get on place, you'll get it.
@fanitram3 жыл бұрын
@@roo8901 got it now but something is wrong, the bike doesn't roll with clutch in, and can change gear without clutch
@roo89013 жыл бұрын
Now after you've screwed the adjustment screw on the clutch lever all the way in, now you have to screw and tighten it outwards until your clutch lever has about 1 cm clearance before it catches the clutch. The screw is only screwed inwards during the cable assembly.
@andreasbigset31653 жыл бұрын
Hey why cant i turn the gear drum after installing
@andreasbigset31653 жыл бұрын
Or turn it freely
@roo89013 жыл бұрын
If you've remembered all the parts in the transmission, the gear drum should not turn completely freely - it should turn when you use a little bit of force and it should click or kind of lock on every gear. So it's not supposed to turn freely like for example the transmission gears but it should turn and click on every gear when you turn it with a little bit of force.
@roo89013 жыл бұрын
If it's really not turning and putting in the gears then check all the parts in the transmission that they're fine.
@andreasbigset31653 жыл бұрын
@@roo8901 i can move it clockwise for a couple of mm
@andreasbigset31653 жыл бұрын
@@roo8901 the parts are almost new
@Yamaha_dt503 жыл бұрын
Why did rexxys video have so many more shims that you had?
@roo89013 жыл бұрын
I've also watched his video and it's because he had the older model of minarelli am6 which has a couple more shims in the transmission than the newer model. The newer model is all the engines after the year 2009 or 2010, don't remember precisely which year...
@juleshummelink76103 жыл бұрын
You forgot the clutch lever right?
@roo89013 жыл бұрын
I assembled it off camera
@crossterror75923 жыл бұрын
At 10:04 did the rod sit flush against the clutch nut or does it sit out a bit. Because mine sat out a bit with the ball but without the ball it sat flush
@roo89013 жыл бұрын
How much the rod sticks out of the clutch? If it sticks out about under 3 millimeters then it should be ok. If it sticks out more from there, try to assemble it while the clutch engager lever on the stator side of the engine is removed. The ball must still be there, otherwise the clutch won't work.
@tobbe39943 жыл бұрын
hi, when I tighten the engineblock screws the crank gets really hard to spin but it spins normally when the screws are loose, do you have any idea why that might happend?
@roo89013 жыл бұрын
When you tighten them after installing new crank bearings the crank becomes under tension. To get it off take the crankshaft nuts and screw them to the both ends of the crank and then tap the ends of the crank with a hammer a few times (prefere a rubber hammer to prevent damaging the threads ). When the tension goes off you notice it right away by looking at the crank. Also try to tighten the engine block bolts in a cross pattern.
@roo89013 жыл бұрын
I got the tension off by giving the stator side of the crank a couple taps with a normal hammer.
@carlo89433 жыл бұрын
WOW bro, do you have a vid of it working?
@roo89013 жыл бұрын
Nope, but works
@tylerwright4973 жыл бұрын
Röö post a video of it running please
@roo89013 жыл бұрын
I have sold that moped half a year ago...
@tylerwright4973 жыл бұрын
Röö ughhh lol
@crossterror75923 жыл бұрын
Did your right crankseal work okay because I put mine in that way and it didnt seal sucked in 100ml of gearbox oil in 10mins
@roo89013 жыл бұрын
Which one of the seals?
@crossterror75923 жыл бұрын
@@roo8901 the clutch side crank seal
@roo89013 жыл бұрын
Alright cause mine has worket always like that, did you remember to put also the o-ring and the metar ring inside the hole of the seal?
@crossterror75923 жыл бұрын
@@roo8901 yes I did. Should the seal sit flush with the housing and the metar ring
@roo89013 жыл бұрын
Yes the seal should be put first (check that the correcr side is facing out), then the o-ring should be pushed inside the seal, then the metal ring on top of the o-ring with the smooth side facing outwards.
@Sido75283 жыл бұрын
11:20 i worked on several minarelli AM6 engines... and that screw on the left is always chewed up at least a little :)
@genij_v_sandalikah Жыл бұрын
It has to be
@hjelme833 жыл бұрын
"a shim" love it
@marcoalessandri6113 жыл бұрын
Thank for this video
@Royal_Enfield_parts_Russia3 жыл бұрын
Спасибо🤝
@daveontherocks31113 жыл бұрын
Do you need a washer between the the balance shaft and bearing?