01-Introduction to Hypermesh

Basic Introduction to Hypermesh for AEM 535 students

[@mbarkey.mechanics]

Note that if you see advertisements on my videos, youtube has put them in there. I have not monetized my account.

[@sbd8397]

you are great,, u told all in one video. thank you Mr. Mark

[@mbarkey.mechanics]

Thanks shanmukh d--happy computing!

[@mahrezaitm.5162]

Many thanks. It is much appreciated.

[@mbarkey.mechanics]

Thanks--happy computing!

[@张洪铭-p6v]

great vedio! it would be great if you can make the cursor bigger, can't find the cursor during you doing some demonstration

[@mbarkey.mechanics]

Thanks. I remembered to turn on the cursor highlighter about 11 minutes in to the video. That is the best I can do at this point. Happy computing!

[@ivannapivdiablyk2027]

Thank you for the video, very helpful

[@mbarkey.mechanics]

Happy computing!

[@chandankumarreddy93]

thanks for the video. it was so helpful.

[@小金-n6n]

Thanks! This video help me a lot.

[@dens3254]

Thank you sir.!

[@boncyragu6903]

thanks for this video sir

[@tapan4253]

i want to see page window layout option is missing in hypermesh 2019

[@aydoganahmet]

thanks for the video!

[@nikhiljha415]

sirji in HW Students version 2020 the Yellow nodes are not visible, can you help?

[@mbarkey.mechanics]

I've seen an issue in Hypermesh 2019 in which the nodes do not appear on the screen. This makes it impossible to use Hypermesh effectively. Here is the fix: create a system variable HW_USE_OPENCL with a value of 0 forums.mbarkey.com/index.php?topic=222.0 see if that helps

[@kavyapaul2062]

sir, how can we recover the MODEL tab(import,part,mask....etc) on the side display....i just accidently deleted it

[@mbarkey.mechanics]

When I attempted to close that area on my screen, it says "use the view > tab area menu to reopen the tab area'

[@estebanllanose.3726]

Dear Dr. Barkey, Could you tell me how to translate *.odb file from Abaqus to *.op2 Nastran file for postprocessing, please? Thanks in advance. Esteban.

[@mbarkey.mechanics]

Hi Oswaldo, I'm sorry, I do not know of a method to do that. There may be one, but it has been many years since I have used Nastran. You may have better luck writing an ABAQUS results file (*.fil) and then looking for a method of conversion. There are also scripting methods for extracting ODB results, but again, I am not familiar with the op2 file.

[@estebanllanose.3726]

Dear Dr. Barkey, Thank you for the quick response! Finally, I could do that. It would be great if you could give me some advice about post-processing Abaqus results. I'm looking for software that allows me to plot 'solution-dependent state variables' used in UMAT because when I plot the contours of SDV's in Abaqus there are negative values ​​that make no sense according to my model. Once again, thanks for your help.

[@mbarkey.mechanics]

I think your best option is still to use ABAQUS CAE directly. Are you sure that your UMAT is providing the correct information? Otherwise, I would think you could code your UMAT to write the appropriate debug information to a file or *.fil file, etc.

[@estebanllanose.3726]

However, when I get a report file from the main menu bar (choosing the positions: at integration point, centroid and nodal) there are no negative values of density in those files. For that reason, I assumed that my UMAT has no errors. I'm a little confused by that.

[@v_naymishra]

how to make the nodes appear. I create nodes but they dont appear unless i put the numbering on. I'm not getting the yellow dot like u are

[@mbarkey.mechanics]

You might look in display options. It has been a while since I have made the video and I don't recall what panel that would be in. If I can, I will take a look later and update this reply.

[@mahdibenrazzouk5547]

hello can somone help, i have a probleme with hypermesh plz

[@SAINIVEDH]

how to open .inp files?

[@mbarkey.mechanics]

.inp are text files. They can be large. I use Crimson Editor, something like notepad++ will also work.

[@maazahmed3583]

.inp is extension of abaqus FE file. u can import through solver deck in Hypermesh. or u can open in using textpad to see fe modal data.

[@pavansudheerbachu4719]

Your cursor is very bigger but not identifi particularly point