1.1.7 Packet Tracer - Basic Switch Configuration - Physical Mode

[@abagail3662]

You have the BEST tutorials, you have taught me more in the last 4 years than my paid instructors. Thank You

[@romeroc24]

Great to hear! Thank you for all your support!!!

[@dc7556]

Just FYI......It is as if it gets stuck at 96%. What I did to get to the 100% completion I saved all my work and closed the packet tracer. Then I reopened it as if I was going to make changes and it showed that I was at 100% instead of the 96% that it showed before. Hope this helps anyone else watching this later. Thank you Christian for the video and the ones you will continue to do.

[@romeroc24]

Thank you for all your support and good observation

[@allifbk33]

THANKS FOR YOUR INFORMATION BROO LONG LIFE❤😂

[@joelxs7819]

Thx

[@eliasjimenez781]

omg you are right

[@WilliamGallagher-xw2eu]

You just saved me a 2nd run through of this lab. You are a legend! Thank you so much!

[@david57989]

Christian, you're the man! I am studying for my CCNA at University. Please continue to make these videos. You have a new subscriber!

[@romeroc24]

Thank you for all your support, you motivate me to continue

[@theemperorstarwarslegends8075]

@@romeroc24 Yeah seriously. I passed my CCNA 1 class with your help. Now onto CCNA 2 class. There's three parts.

[@romeroc24]

@@theemperorstarwarslegends8075Thank you, you are motivating me to continue with this for long time

[@stevem2757]

Hello Christian! Thank you for all your hard work, I wanted to send you a comment before. I subscribed to your channel today. And I owe you thank you for all you do for the Internet community. Thanks again!

[@romeroc24]

Wow, thank you. I appreciate all your support, thank you again

[@normdeplume6315]

thanks Christian this is the only tutorial which is up to date with the current SRWE course

[@romeroc24]

Thank you for all your support

[@ndohcollins2050]

Mr Christian this is really a fantastic job: well explained, well understood, and well explicit, pls continue, switch configuration on a trunk.

[@romeroc24]

Thank you for all your support

[@CaliKPC]

Thanks Christian! I went to bed last night at 96% and when I woke up and loaded the PKI file it was at 100% and I hadn't changed anything. It had the same error you had at the end. Not sure why that happened but it worked.

[@romeroc24]

Thank you for all your support, great observation, it's a packet tracer bug

[@theemperorstarwarslegends8075]

Don't question it. That's something you learn in coding. If it works, and you don't understand why, just let it be.

[@romeroc24]

@@theemperorstarwarslegends8075 Yes because all is configured correctly

[@iiCharlemagne]

my instructor told us that when we get stuck at 96%, somewhere down the line, we were supposed to implement a static route: S1(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.1

[@romeroc24]

@@iiCharlemagne very nice option to try

[@St1mi]

Hey I can already tell; you videos are going to help me so much more than my teacher of Cisco II is... so thank you thank you!!

[@romeroc24]

Thank you for all your support, this is the motivation I need, thank you again

[@joec4844]

Thank you so much for this. You help me so much more than my online teacher.

[@romeroc24]

Happy to help! I appreciate all your support!!

[@dandoapp1025]

Christian, you are a Genius my friend

[@romeroc24]

Thank you for all your support my friend!!!!

[@scottb6176]

Thank you for the video! Keep them coming, please.

[@romeroc24]

Thank you for all your support, I appreciate it

[@camilaaltamirano3000]

Christian thanks a lot men, you are helping me to get trougth my CCNNA certification

[@romeroc24]

Thank you for all your support

[@xxdavidxxyt1555]

I can´t thank you enough... thank you professor Romero.

[@romeroc24]

thank you for all your support, I really appreciate

[@ucambo1]

Thank you for sharing your knowledge Christian!

[@romeroc24]

Thank you for all your support

[@Yiyex11]

Hi! before any question... jus say what an incredible help this is for me and many others that stumble upon your content. Very much appreciated all the efforts that you put out in this videos. Now my question: In this video, you checked the vlans and the vlan 99 was in the list with the command "show vlan", why you have to create it with the command "vlan 99"?

[@romeroc24]

Thank you for all your support my friend, vlan 1 is created by default and is assigned to all ports, vlan 99 is no existing by default, so the way to create it is using vlan 99 command

[@stokes628]

Definintely earned a sub. Thank you for the help and the walkthrough.

[@romeroc24]

Thanks for the sub! I appreciate all your support

[@kemomaynard5417]

Gracias por todo amigo.

[@romeroc24]

GRacias por seguir estos videos

[@thecreatornooj1328]

thanks so much, my professor isn't really useful for this kind of help, and meandering through the modules alone wasn't working for me either

[@romeroc24]

Glad it helped! Be careful with the details in the videos

[@fodecissokho9918]

Thanks man !! you are killing it Eveything is well explained .... keep it up G- 🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥

[@romeroc24]

Thank you, I really appreciate it

[@robertabbud9130]

Muchas gracias por tus videos!

[@romeroc24]

Aprecio todo tu apoyo, gracias

[@jacobykabeya530]

My Hero !!!!!!!

[@romeroc24]

Thank you for all your support my friend!!!

[@inferno3345]

goat

[@romeroc24]

Thank you for all your support my friend!

[@ІванШвець-л2ь]

You are THE BEST!

[@romeroc24]

I appreciate it, thank you

[@Recony0]

thanks so much 🙏🏾

[@romeroc24]

Happy to help

[@brianpmcg]

thank you for the instruction.

[@romeroc24]

You are welcome!

[@AdreetoShowmik]

when i reached the terminal at part 3 it asks password after s1> enable the password should be cisco as I set it. but it is saying bad secrets. HELP

[@romeroc24]

maybe you configured wrong password, now you can start again and do it again

[@salimataba8547]

Merci beaucoup

[@romeroc24]

Merci

[@ekoajiputra9431]

its great wonderful. thank you

[@romeroc24]

Thank you too!

[@chrisaelus6258]

stuck at 96%, i checked the results and it shows the FastEthernet0 having an "X" mark on IP Address. how would i reconfigure this?

[@romeroc24]

configure the interface again, then the new IP address will be applied

[@jasminechebet5030]

I have tried severally but my packet tracer won't accept ipv6. I keep getting invalid input

[@romeroc24]

Please use the same file I shared on video's description

[@enlightenmentdoesntcomeeas5337]

at around 28:51 when I enter the ipv6 address 2001... it keeps saying "invalid input detected."

[@jasminechebet5030]

Same here. Did you manage?

[@enlightenmentdoesntcomeeas5337]

@@jasminechebet5030 Yeah I just got a friend to fix it for me.

[@romeroc24]

The exam sometimes only requires IPv4 configurations, review the instructions on the exam

[@GarbanzoBeansFan]

thank you for this tutorial

[@romeroc24]

You're welcome 😊

[@dimitrishp7305]

Thanks. Nice video. I spent to much time to figure out what is wrong with the default gateway :(

[@romeroc24]

Glad I could help!

[@corex9019]

thanks for this video

[@romeroc24]

Thank you for all your support, I appreciate it

[@MinecraftGuy2]

thank you

[@romeroc24]

You're welcome

[@klari0n11]

thanks for helping me

[@romeroc24]

Happy to help, I appreciate your comment

[@mchvz3780]

Hola, que buen contenido tienes sobre redes, te lo agradezco me has ayudado mucho, una pregunta, como puedo poner esa vista que tienes para ver los equipos en 3D ?

[@romeroc24]

Gracias por tu apoyo, tienes que ubicar unos dispositivos en logical mode y luego elegir physical mode en la parte superior izquierda, aparece una ciudad, haces click en ella, luego aparece un edificio haces click en el, hasta que aparece un cuarto de comunicaciones haces click en el y verás los dispositivios

[@NaNa-bt6or]

In my terminal is blank.. so I can't configuration... Why that is happen??

[@romeroc24]

maybe you can send me a screenshot using social media shown in 00:03

[@erronsosa6232]

Amigo, tuve un problema, exactamente en el momento que vuelvo a Terminal, pasa que me pide la contraseña, le doy la contraseña ¨cisco¨ se abre el modo normal entonces pongo ¨enable¨ y me pide contraseña yo le doy ¨cisco¨ de nuevo, pero ahora, por alguna razon, no me deja accesar ¿a que crees que se deba?

[@romeroc24]

es que la contraseña de enable es distinta, debes iniciar de nuevo

[@lizethorellana5355]

la contraseña para el enable es class

[@erronsosa6232]

@@lizethorellana5355 Muchas gracias linda, ya lo había entendido, ya hasta me gradué xD Pero gracias igualmente.

[@ramosquispekattyshirley9997]

@@lizethorellana5355 muchas gracias!

[@angelmelo4283]

Tengo un problema con el S1> ..mi packet tracer se pone en automatico y no puedo salir o avanzar de ahi, me pide password...

[@romeroc24]

no hay una constraseña, seguramente configuraste una y no la recuerdas, inicia de nuevo la actividad

[@i124qusb]

same . 2 times happened to me😞

[@ireneougsangjr.9383]

thanks man

[@romeroc24]

Happy to help

[@albertr.palbert8610]

My progress is 88%, there are problems included in IPv6. how to solve it, thank you

[@romeroc24]

please review all the video at detail, thank you my friend

[@FrancisGerardA.Caraan]

what should i do for the last 4%

[@romeroc24]

maybe 96% is very good for now, anyway some files may have issues

[@EliaraTafao_]

Im stuck at 96 it didn't reply to the Ping and also I went back to terminal and the pw ain't working..I swear I put in cisco

[@romeroc24]

please be careful with ipv6 addresses and ipv4 addresses configured on devices, review all

[@soldier1662]

just starting the video, what messes me up is on the topology it says Fa0/6 but on the physical switch its all gigabit1/0/0 shit.

[@romeroc24]

you can use any switch port but to get the 100% score please use the example in the video

[@deidrawhetung1373]

I'm stuck on the stupid default gateway... Could you help? Like whats the timestamp if you know

[@deidrawhetung1373]

33:16 for anyone that was stuck like me

[@romeroc24]

what is the problem?

[@borjavalientecastellano1774]

Gracias por la ayuda amigo pero no puedo completar la actividad por un motivo y no localizo el fallo. En assestment items, en el apartado de IPv6 Address 1 la Prefix Length me aparece cómo incorrecta. Podrías pasarme el min del video en que lo haces o decirme cómo checarlo por mí mismo? Gracias

[@romeroc24]

Es una IPv6 mal configurada en el switch o en la PC, revisas esas direccione IPv6

[@borjavalientecastellano1774]

@@romeroc24 era en la pc, puse 24 en lugar de 64 en el prefijo MAC -_- muchas gracias!

[@romeroc24]

@@borjavalientecastellano1774 excelente

[@soldier1662]

I get invalid default gateway message

[@romeroc24]

the default gateway should be a valid host ip address

[@LionTobiAsakura]

Por qué no se puede llegar al 100%?

[@romeroc24]

Hay un error en el archivo, porque todo esta bien configurado, no hay problema

[@LionTobiAsakura]

@@romeroc24 muchas gracias

[@wilsona.vilcaguerra6038]

Gracielas.

[@romeroc24]

De nada, saludos