1-30v 0-10A variable power supply| LM317 voltage regulator| Adjustable power supply

in this video i will make a variable voltage and current regulator. lm317 used as voltage regulator which can regulate 0 to 37 volt and TIP-3055 transistor used for current. this is variable current and voltage power supply.this voltage regulator circuit contains ,TIP-3055, regulator lm317 ,resistor, capacitors,potentiometer, dc volt meter.this adjustable voltage regulator can be use as battery charger. electronics lover
#voltageregulation
#voltageregulator
#current
#lm317
#variablepowersupply
#vbatterycharger
#powersupply|
#electronics lover

[@nagarajub4011]

Please add circuit diagram

[@electronicslover1450]

I will add it soon

[@vratislavnyvlt3947]

​@@electronicslover145010:38

[@marian20012]

@@electronicslover1450 well, where is the circuit diagram?

[@SunilJayakodi-yr5eg]

❤❤❤❤❤❤❤❤❤very nice video ❤❤❤❤Thank

[@zarkoujdur9424]

This is a ridiculous advertisement. Those wires cannot provide 2 Amperes... 10 Amperes is science fiction... ))

[@WongNdesoCreative]

thanx u for tutorial

[@gajrajsingh2627]

Bahut khub.

[@user-ex2bc4kz3c]

Impressive

[@technical_skill_rohit]

Good job brother

[@electronicslover1450]

Thank you so much 😀

[@chandersheikher7071]

Can you design power supply usi Thyristor. Please tell.

[@LeonardoRamirez-cl8ts]

Can be used at 1V 10A for voltage injection on gpu?

[@roopg3018]

Very nice bro

[@velialici7980]

Çok güzel bir devre olmuş. Beğendim ve yapmak istedim fakat DEVRE ŞEMASI OLMAYINCA BENİM İÇİN ZOR OLACAK.

[@SOYLU_TURK]

Bende var ama biraz karmaşık

[@alanpecherer5705]

Back in the 80's I worked for an electronics company in Los Angeles that routinely went through its shelves and threw out parts, for what purpose, I don't know. I *do* know that they were trying to manipulate their P/L. They also received lots of sample parts from manufacturers who wanted to become suppliers. But on those days when they threw stuff out, their dumpster was an absolute hobbyist's dream. I got bags and bags of brand new 2 watt resistors, but the best find was a bag of 500 brand new LM350 regulators in TO-220. It would have been nice if ebay existed back then. I probably used 3 of them and either gave or threw the rest away.

[@ramanarao32]

wow!! you threw the remaining LM350s?😇😇😇😞

[@alanpecherer5705]

@@ramanarao32 Yeah, tragic, bordering on stupid. They were Motorolas, too. But how many can you use? I was in a situation where I had to get rid of everything I owned, the LM350s weren't the only victim.

[@sjsj346]

Super super super super 👍🙏🔥

[@ecengambhatt]

But why dont you use general purpose PCB. This is not the way to solder components...

[@Wonge.teko.productions]

9:59 schematic pls sir?

[@hakanakca2906]

hey gidi günler heyyyy, ortaokul zamanlarımmmm

[@roshansumeda-wz7or]

What is the input voltage and amp you gave

[@user-ic9lu3lq6q]

Will the circuit work properly if I use 19.5vof 2.31A charger of laptop and connect its output with dc to dc step up module (XL6009) and adjust it to 24v dc and then connect this output wires to 300watt dc to dc 10A stepdown buck converter to get a output voltage varies from 24v to 1.2v?

[@Edmorbus]

please diagram circuit

[@latheef1919]

🎉

[@NecaettinKugu-fv1ns]

1 ay önce yazılan yorumlara cevap vermediğine göre bu devre başka bir yerden kopyalanmış olmalı. Yoksa neden devre şemasını vermesin ki?

[@madhusudangupta3661]

I too have the same opinion.

[@prasantasanyal10]

What should be the rating of step down transformer and the rating of input dc to controller circuit.

[@DIYMaintenance]

Impressive making. Keep it up

[@electronicslover1450]

Thanks a lot

[@tonyd1149]

Nice job on that. Thank you for making and posting this video. 🙂

[@electronicslover1450]

thanks

[@waseemraza1437]

upload more videos like this,,,,❤

[@electronicslover1450]

I will try my best

[@francescobritti2119]

A scopo didattico sarebbe utile anche lo schema elettrico

[@roshansumeda-wz7or]

Circute diagram pls

[@user-jz4sm6io3c]

great please diagram circuit

[@naushadahmed9680]

What will happen if voltage controlling pot will open faulty। BOOM😅

[@migueloyarzabal]

Add circuit diagram

[@zequipostor3979]

Me gustó el vídeo. Pero veo que no llega a 30v? Quiero hacerla

[@electronicslover1450]

para llegar a 30v necesitamos una fuente de alimentación de 30v... no tengo una fuente de alimentación de 30v, por lo tanto, solo uso una fuente de alimentación de 17v...

[@Alves711]

tanto esta como a anterior gostava de ver atingir os 10 amp, de certeza que os potenciometro pagavam fogo, onde é que está o consumo dos 10 amperes?

[@jibrantechnicalhelps]

Diagram ???😲😲😲

[@snipernacer]

BONJOUR svp premièrement 1 je veut avoir un convertisseur de dc vers ac 12V DC to AC variable ( 3V 12V 24V au 30V AC) . 2 SVP je veut encor pour fabriquer un variable de AC to AC AC 220 V vers AC de 3V AC a 30V AC //// merci beaucoup chemachema

[@wirebrushproductions1001]

Here is a challenge. Get a 30 volt, 10 amp supply to provide power, and hook it up to the input. Set the output to 1 volt. Make a load using a 2-watt, 0.1 ohm resistor. At 1 volt it will draw 10 amps. Start a camera taking video of your box. Connect the load. Watch your circuit fail. Publish the video on KZbin. That circuit cannot possibly provide what you claim it will. At the least, the heat sink is puny and the pass transistors will overheat and fail. For an output of 30 volts and 10 amps, you''ll need at least a 35 volt input supply, since each 1 ohm resistor will drop 5 volts. Worst-case stress on the transistors is not at a high output voltage, but at low output voltage.

[@user-qz7uf6jf3g]

Si de verdad quisieras enseñar...mostrarias el diagrama elec. Y asi seria facil.....

[@user-wc6mj2jj6x]

Никому не интересно смотреть как он паяет. Где схема . И 10 ампер он не выдержит. Обман

[@electronicslover1450]

мне нравится ваше мнение .. извините, что не добавил диаграмму, я постараюсь добавить диаграмму .. и постараюсь сделать все возможное в следующий раз

[@ranjankumarbhattacharyya9941]

Use a heat sink with transistots

[@electronicslover1450]

Heat sink used ..watch all video

[@wazaifulislam4597]

Good yar

[@electronicslover1450]

thankx

[@user-dn8sg1js5l]

سلام استاد استاد الارغم تناسب وات ورودی که باید ۳۰۰ وات باشه ایاورودی مدار باید ۱۰ امپر وولتاژ۳۰ولت باشد ؟ وچگونه میتوانیم در صورت تناسب وات مقدار چه ولتاژ و امپر رو افزایش بدیم متشکرم .

[@denisnam9298]

Вечно пишут 10 ампер 30вольт а как доходит до теста так вечно то светодиод в нагрузку то кулер компьютерный гдееее реальная нагрузка гдеееееее хотя бы галогенку автомобильную.

[@user-hn1gd5zj1w]

Потому что для реальной нагрузки нужен Большой радиатор и его надо охлаждать Сильным вентилятором...Кто занимался этим знает,что это такое.

[@pankajnikam8969]

Input voltage kitana diya sir

[@electronicslover1450]

I have 14v power supply for input and i use it..

[@nagarajub4011]

Hi brother, i am new to electronics, what is solution you pasted to that box? and what is that in between middle of heat sink and transister you put ? Please tell names of that brother

[@electronicslover1450]

The solution i pasted to the box is super fast glue ..and in middle of heat sink and transistor is thermal insulator pad

[@nagarajub4011]

@@electronicslover1450 thank you brother

[@nagarajub4011]

@@electronicslover1450 brother where these all parts are available to buy?

[@electronicslover1450]

@@nagarajub4011you can buy from any electronics shop or buy online in your country

[@nagarajub4011]

@@electronicslover1450 ok brother thank you

[@Accumulator1]

No heat sink, electro-crap 😄

[@eddyyu7091]

Hard to see without schematic !

[@electronicslover1450]

i will try to add a diagram

[@chandersheikher7071]

Circuit not shown

[@islamismyway992]

Good work sir.....please can I get the circuit diagram?

[@electronicslover1450]

Sure .

[@islamismyway992]

@@electronicslover1450 ok sir please help me with the circuit diagram 🙏

[@madhusudangupta3661]

​@@electronicslover1450 Even after good two months your promise is left unattended like an idiot made it.

[@GhulamMustafa-xm1rf]

Non professional. Don't know how to do and how to show.

[@electronicslover1450]

In future ..it will better

[@madhusudangupta3661]

In the absence of a circuit diagram, the project seems copied by an ignorant person.

[@electronicslover1450]

I will add a circuit diagram soon ...

[@madhusudangupta3661]

​ @Electronics Lover It is said, Promises fail but efforts yield result. Your promises to upload a circuit diagram have failed for more than six months. Please make effort.

[@electronicslover1450]

@@madhusudangupta3661 yes you are right sir..i have worked on diagram but don't know how to add it after uploading a video..

[@electronicslover1450]

@@madhusudangupta3661 secondly ' i am new youtuber and near to monetization of my channel therefore i am not making any changes in my videos ..soon i will try to add a diagram...i hope u understand...thanks alot 😍

[@madhusudangupta3661]

@@electronicslover1450 You can response on the circuit diagram in the comment or in the description section. Thanks for understanding the importance of the Circuit Diagram for an Electronics Project.

[@JohnSchiavoneJrBSEERN]

talks to much