10 Useful 3D Printed Tools #2

[@Rebar77_real]

Nice stuff. That "equal spacer" could use a wingnut on a small bolt to lock it in place to keep going without error. Thanks for the link!

[@simonrancourt7834]

In #2, how do you change the blade, if it's all glued ?

[@jasond9824]

It appears to lock in the blade out position, but not lock in the safe to carry position. What a stupid overall design flaw

[@chrisnupp7097]

@@jasond9824 I printed one, it locks it into both positions.

[@chrisnupp7097]

It's not supposed to be glued in place. There's a tab by the blade divots (where the blade locks in place) that you can push out of the way to remove the blade and replace it.

[@theanimationkingdom4]

U cant.

[@RVBFan182]

4:33 never actually use a razor blade on your print surface unless you want to ruin that surface.

[@miked9959]

I enjoy this type of video and appreciate the time and effort you put into it. It's a great way to get ideas for future prints. Thanks!

[@3DPrintsBuilds]

Thanks!

[@Sembazuru]

For the tire tread depth gauge and the bolt&nut sorter you can color the legends a little easier if you switch filaments to black (or other contrasting color) for the last couple layers. That'll save the marker issues that I always have of the ink running down and bleeding across the face of the part. The issue with the marker on the square is probably because the markings were debossed (sunken into the surface) instead of embossed (sticking out of the surface) like the tread depth gauge and bolt&nut sorter. But, since that was printed with the markings on a vertical surface, the color changing trick would be a major pain even on a printer that has decent M600 support.

[@arne6787]

Spray can handle needs an adjustable end stop so u can just sqeeze handle and set the exact spray volume without the need to hold just the right squeeze to get what u want for spray pattern.

[@wanderingcalamity360]

Did you just super glue what is supposed to be a replaceable boxcutter blade into that "faker knife"?

[@budgiefriend]

Thank you for the update.

[@carlosgroes8573]

The nr10 yellow bolt and nut sorter.. you got a link? For the file

[@3DPrintsBuilds]

Link in the description.

[@tlocke0259]

What settings did you have to change on that first print? I’ve had that problem with one of my printers and don’t know how to fix it.

[@3DPrintsBuilds]

I changed line width from 0.3 to 0.4mm

[@3design284]

nice combination of useful tools. keep uploading. good luck .

[@3DPrintsBuilds]

Thanks!

[@taranagnew436]

for the nuts & bolts shorter, you should add the size to the nut side

[@mateusztokarski7553]

I have the same problem witch my 3d prints that you in first print. What did settings you change.

[@3DPrintsBuilds]

Changed line width back to 0.4mm

[@S....]

Nr. 1 Trim/Clip popper - what filament is it, please?

[@3DPrintsBuilds]

PLA

[@S....]

@@3DPrintsBuilds Dude.. what brand / color? xD

[@3DPrintsBuilds]

@@S.... Gembird Gold Metal PLA

[@Priceman5]

Do you have your print settings displayed anywhere? I just got a ender, and my prints never come out looking that nice.

[@3DPrintsBuilds]

Cura profile for Ender 3 V2: www.mediafire.com/file/sxlrfx1jiebkcif/Ender_V2_Basic_settings.curaprofile/file

[@mohammadajmin1542]

Look so cool that bro

[@ElecTechie]

Nice .. Can I have the wood burner link and permanent marker link?

[@3DPrintsBuilds]

Wood burner: s.zbanx.com/r/0oD7Tzj2iDwR Permanent marker: euro-industry.com/main.php?index=details&cat=8&prod=23201550&lang=de

[@Kevin-wy8kc]

amd why didnt you loosen the oil filter cap that fit perfectly?

[@alexistaboada5759]

Bc the tool would have disintegrated with any amount of load

[@kotsioschristou8472]

what cura settings are you using for those clean prints?

[@3DPrintsBuilds]

I have different settings for different prints, but I can share my basic Ender v2 PLA profile: bit.ly/2Zg40Ff

[@jonathanpaz5453]

What did you applied to the spring?

[@3DPrintsBuilds]

I applied grease.

[@styxx0500]

It's more expensive to make these than it is to buy ones that are readily available on Amazon lol

[@pcerano742]

Lol. Most of these prints probably cost less than $1.50.

[@styxx0500]

@@pcerano742 and yet, they aren't even worth $1.00 🤣

[@vickys9191]

Print = 'auxiliary handle' for drill machine.

[@imaker3183]

Привет а ты не печатал корректоры в фары для е39. Спс если есть стл скинь плиз. Удачи

[@granul555]

Hi. Which slicer do you use?

[@3DPrintsBuilds]

Cura

[@granul555]

@@3DPrintsBuilds How did you get the numbers printed on top? They look bad to me when printed.

[@3DPrintsBuilds]

@@granul555 Look over your print settings. Maybe you need to slower down or change layer height.

[@granul555]

@@3DPrintsBuilds Can you please share your Cura settings?

[@3DPrintsBuilds]

@@granul555 I use different settings with different prints and printers. Here is one of my Ender V2 settings: www.mediafire.com/file/v0l8ifqz7seiazs/Ender_v2_0.2mm.curaprofile/file

[@jasongibson4539]

On your recessed groves,(like the carpenters square) you should try a wax crayon 🖍 instead of a sharpie. It works great. You can rub off any excess with a paper towel for clean marks.

[@3DPrintsBuilds]

Thank you for the idea. I will try it someday.

[@3dprintingmodels913]

i like the concept very much 💕👌👍

[@robinferdinando4038]

Awesome video and content 👌 what does R. F on the oil wrench mean?

[@3DPrintsBuilds]

Thanks! The R. F. are the initials of the designer. Rusty_Fly

[@Ghazkul666]

You have a typo in your ad, the word you want is "stuff" not staff

[@tbm7301]

i saw that 3d guns folder, can't stop the signal.

[@psdmaniac]

Only spacer and bolts measure tool are useful. The rest are good only in collecting a dust or filling recycle bin.

[@3DJapan]

Whipping that blade around was freaking me out.

[@ryanokeefe12]

Lol... why did you glue the blade into you knife?

[@markschweitzer6920]

Why would I go through the tedious task of making that brush when I could do the same job with a cheap 25-cent chip brush?

[@therealfocusin]

Jump to 8:43 believe me, watch till the end. Don't waste your time like I did.

[@johnschroeder6351]

I will have to get my printer set up so I can utilise it better.

[@dldgranite1931]

Is everybody just that messed up every one of those things that I see I don’t have the design I don’t have the figure out the way to print it or make it I don’t have to buy the printing material to do it it’s already there all I Gotta do is go to the damn store and buy it and once I figure out the time spent and the printing material it’ll be about 75% cheaperIf I just go buy it

[@andrewjackman8926]

Got a headache reading your comment. No punctuation?

[@bossmassful]

Полезные инструменты? Ну уж линейку то можно купить в магазине. Как и почти всё остальное

[@Сергейчехонадских-й6ъ]

👍 👍 👍 👍

[@makewithmegma]

🔥💕👌👍

[@chibyshev]

Игрушки и ее более того.

[@pgramsey1]

#1 You are better off buying one of those at Harbor Freight . 3D printed plastic is going to break. #2 You are better off buying one of those at Harbor Freight. . 3D printed plastic is going to break. And you can change the blade. #3 You are better off buying one of those at Harbor Freight . . 3D printed plastic is going to break and be of unknown accuracy. #4 You are better off buying one of those at Harbor Freight. . 3D printed plastic is going to break. But if you insist there are much better designs out there. #5 You are better off buying one of those at Harbor Freight . . 3D printed plastic is going to break and be of unknown accuracy. Quitting. 3d print things when you can't get something better for pocket change at Harbor Freight.

[@3DPrintsBuilds]

There isn't Harbor Freight everywhere and the prices are also different. Yes some of the things last longer when not 3D printed, but it depends how much you use them. Also some of the things you can print 2 or 3 and still cheaper than to by one.

[@ErCapoAlex]

Hii

[@yomiyoo]

Or maybe just buy a cutter and save the 6 hour of printing

[@rubino1988]

If you have to use super glue on a removable part it's not convenient

[@TsurinoDazuji]

gdzie na stole kroisz.. matka by Ci zaraz pokazała ciachanie na stole

[@dr.emmettbrown8466]

Самоделки полная хуйня (с) Доктор Дью ((((

[@rynait]

the #2 is useless.

[@3dcrazy332]

☝️ I'm the first person to design "print in place" brooms and brushes about 8 years ago.

[@unknownflyer90]

Can't you spell?

[@ДмитрийАндреевич-я5м]

Useless

[@MrToufou54]

Seriously ? What have you done here ? You are not the owner of designs, you just publish timelapses of your printer printing other guys work !

[@warmesuppe]

Where does he/she claim that?

[@LoreLibrary-Official]

Where do they claim its theirs

[@brandielee7971]

They don't claim the designs are theirs, and they link the the stuff. It's just to make people aware of the files

[@MrToufou54]

So, yes everybody, but where are the credits (in the video) ??? Where is the creativity ? What does this video give more than a search on stl search engines ? I'm just saying that there is no work on this video... I'm here for having more that just that I could by myself

[@LoreLibrary-Official]

@@MrToufou54 yes u can do it yourself..this just show to people that these file exist..the maker of the file allot them to do this cuz its freeeeeeeeee

[@WoodenCreationz]

I need one of those Faker ꓘnifes.... lol Thanks for the share.. Just stumbled upon your channel!!!