1000W simple inverter powerfull

[@PhdHung]

This is a simple but powerful inverter. It only uses 6 mosfet IRF3205 and 4 resistors. although simple, it works very well. The power of this inverter depends on the transformer, the large transformer is large power. Facebook group : bit.ly/CreativeElectronic Download file here: mshare.io/file/zQX5nbC9

[@beytullah7796]

Türkçe dil desteği yokmu 🤔

[@vsftpd]

Capacitor connection missing

[@AjayPrajapati-ix2uz]

Battery charger Alag se lagna padega kya?

[@vipin.sureshwar123]

Transformer kitne amp. ka hai

[@rockyrocks1629]

In diagram there is no capacitor, which line you are connected to capacitor from Transformer.can you tell me Please.Also there diagram and your practical work is not same in diagram there is no connection in between both mosfet set directly, but in your video is not like that.what will work really ?

[@edwardbartolo6382]

Show your subscribers the following pieces of information: a) the waveforms at the Mosfet's gates b) the output waveform c) the operating frequency plus the percentage drift Do calculations for the circuit efficiency, frequency drift and short circuit tolerance. Electronic circuits are normally complex for very valid reasons, which are often stability and reliabilty. I am writing from experience after attempting to build an amplifier. At first, I was interested and actually built a simple amplifier circuit complete with a differential input, voltage amplifier stage and power stage. The result was 'good' but not as good as one expects from what one reads on the internet. Finally, to avoid bitter disappointments for the very eager: Electronic components are often burdened with unwanted properties normally referred to as parasitics. Readers should note that these parasitic properties are often significant. I suggest readers read about how amplifier topology and physical design change with frequency to get an idea.

[@فتحى-ه5ر]

اشكر شكرا جزيلا..لقد اطلعت على الفيديو واستفدت منه الكثير رغم انى لا استطيع ان افعل مثل ما فعلت لقلت الامكانيات الا انى اشد على ايديك والله يفتح عليك

[@jhossanantonio557]

This video is the best thanks Homemade 102 for your knowledge this is the best video do not you think of deleting it from your channel that is very useful

[@PhdHung]

[@hrm939]

Curcuit diagram pls sent bigg battery use with charging

[@sermannhoffman1498]

The transformer is the great trouble, thanks a lot.

[@lukeman8880]

I used irfz 44n and I worked great without significant drains from the ba3. Am really enjoying it now. Thanks bro

[@PhdHung]

[@lukeman8880]

I really appreciate sir, am enjoying thus type of inverter comparing to the formal one. Pls how can I increase the current or frequency. Expecting ur reply sir

[@leandrolopez4113]

Grande amigó!!!! El canal de los inversores 💯🇦🇷💪 indiscutible

[@zoheb4you2002]

After lots of try today i made it, even the drill machine is working but just one problem light fluctuates too much, hope will solve later thank u

[@PhdHung]

try adding a filter capacitor at the 220V output.

[@RaedZahr]

Connectivities are not clear yet the idea is perfect

[@RayhanElectroniks]

Perfect your project Heavy quality

[@theophilusothoigbe5779]

Quite good, but connection of the transformer (marking clearly the primary and secondary 12v-0-12v) to MOSFET network should have been explained. That's the down side of this tutorial.

[@siggyretburns7523]

Yeah. That would have been nice huh. But atleast its better than the download diagram. Its bad.

[@sreejithtg8562]

Did you get transformer connection diagram.

[@ChimaobiOnwuka]

I love your hand work, please any miss to get the diagram of it ❤, this is the most thing I like in my life.

[@milanchakraborty1052]

NOT SO CLEAR PLEASE DISPLAY WITH CIRCUIT AND CONNECTION DIAGRAMS...THANKS.

[@OVANHUNG36]

The drive runs very well you great videos

[@PhdHung]

[@sreejithtg8562]

Hi

[@frankomyto]

Very, Very good man, congratulacion

[@PhdHung]

thanks bro, Thanks for liking it, have a nice day

[@ahmed-najdi6818]

Very nice, you are using a converter, how many amperes or volts?

[@Stick_manvideomaker7]

Nice and simple work thanks for that butcould you say me which capasitor did you use for filter?

[@berman9668]

Thanks my friend , for you i understand all , is very easy , you are owner ,greeting fron Spain.

[@PhdHung]

[@abdulhafeeznawabkhan3995]

Excellent work sir i like ur videos from my heart pakistan

[@PhdHung]

thanks bro

[@sauravsah2179]

Sir aapka video bahut pasand aaya . Lakin sir Kya aap apne transformer ka strack length aur uske bobbin ka chaurie size batayenge please kruki Mai bhi same inverter banane vala hoo

[@PhdHung]

?

[@damaariawan2122]

when i watching it, voltage a bit drop.. i just thinking,, let's make another video for stabilize the voltage..

[@PhdHung]

ok, wait me

[@marthadsilva2953]

Is it step up or step down transformer?

[@swapnamoyhazra6036]

@@marthadsilva2953 fir inverter we have to use step up Transformer, and for rectifier charger we have to use step down transformer

[@edwinarcenal5770]

use ixtn660n04t4

[@Electronicview]

Great video friend lik and stay connected ♥️

[@PhdHung]

Thanks, hope you enjoy it

[@RenovaProjetos]

Muinto bom amigo.vou tentar fazer.

[@anatoryjames4128]

Hi my friend your project is very nice and its very well done because i triying it and its ok but i want ask you the question can i add more mesfet ni order to get more power ? thanks

[@logenxman7642]

I think it will be the transformer of UPS, isn't it? And where is the connection of capacitor?

Hello máy kích cá này quá chừng mạnh mẽ hơn bao nhiêu tiền day anh thank you OK Hello

[@muhammadsadiq4826]

Pl show diagram circuit of this project on paper

[@aggpakelectrohobby]

kzbin.info/www/bejne/jZ_UZIN-orpraac

[@puddin-ct4gc]

Muy interesante pero que la energia del taladro la generan solo los transistores o tienes algun voltaje aparte sacado de alguna pila ....si no ocupas ni una pila te aplaudo por ese invento seria magnifico energia para todos

[@PhdHung]

:D

[@sanctuaryjames3434]

Can you please design low battery automatic cutoff for inverters? One that will disconnect the battery from the inverter automatically when there's low battery around 10.8 Volts. Thanks

[@PhdHung]

ok, wait me

[@sanctuaryjames3434]

Alright. Thanks, I'll be waiting bro.

[@mohdsyafiqmohdzaki66]

1 month later~~

[@ElectroPozitive]

This very informative video, i like it, keep it up.

[@brazilfuturo2181]

Aí só faltou montar um circuito para estabilizar os 227v.

[@PhdHung]

ZVS circuit can not stabilize the voltage, when the load is large, the voltage will drop down.

[@mortazayazdanparast84]

Hi, thanks for the video. Can I use any type of mosfet like F16C20C,S20C40C,S16C40C with other mosfets or should they all be the same?

[@PhdHung]

All N-mosfet possible

[@mortazayazdanparast84]

@@PhdHung Thank you for answering

[@ClecianoSilvaKl2023]

Tenho um transformador de nobreak 15+15v posso usar nesse projeto meu amigo

[@PhdHung]

Yes, but the voltage may be lower than 220V. could be 200V.

[@420indore2]

bohot bohot shaandaar sir ji......boss pls. 2000 watt home made strong inverter bhi bataiye pl.

[@esaienganadingamtoudji8265]

Hello, Thanks for that good design. One question: What is the value of the capacity used between Source and 0 of the transformer.

[@PhdHung]

1000uF > 4700uF 25V

[@esaienganadingamtoudji8265]

@@PhdHung Thanks! I'll make the inverter and then let you the result.

[@esaienganadingamtoudji8265]

...and then let you know...

[@osarenagharumeshach4437]

Really powerful. Pls could u post more videos on how to recharge your batteries. Also what kind of battery did you use in the 2000wtts?

[@ramukarri3327]

Bro please send me clear details for the 12v transformer connections

[@rajehsaassouh370]

Centertape transformer 12 0 12 0 to +B .and 12 to each side of the source of mosfets

[@rozimehra5455]

Rong no hai j

[@rozimehra5455]

Bhai fake hai bina pulse ke nehi chal sakta dc volt ko ac pulse ki jaroorat padti hai faku hai

[@zubairshaikh2429]

Hey bro.. mere paas mini inverter hai jise hum emergency b kehte hai.. kya usko 5 amp ka transformer laga k upgrade jar sakte hai ? Badi battery bada inverter me ?

[@PhdHung]

Sorry . I don't understand

[@marcosouza3824]

Esse é poderoso não cai nem a tensão!

[@PhdHung]

:d

[@asanterichard9498]

Pls how do I make it pure sine wave so I can fridge on it,? I enjoyed your masterpiece.

[@PhdHung]

There are many sine inverter videos on my channel. Please search in the video list

[@asanterichard9498]

Homemade 102 thanks

[@stanleynwaoha9531]

please can this inverter recharge it's battery by self

[@arunkumarvadla7563]

Hi Hung Pham, what is the frequency of this inverter ?

[@PhdHung]

~ 50hz +-3

[@unknown-yn1no]

Dont have frequency? depends on the transformer, the large transformer is large power.you have to make insurance for your Family and your House Before Make this inverter. thank you

[@ismaeilalhaialy2538]

Good work bro can I use irf 1010E mosfet?

[@PhdHung]

I think ok

[@ismaeilalhaialy2538]

@@PhdHung thanks bro

[@azadhesimov516]

Super. But where is the diagram ?

[@PhdHung]

in the video description

[@shouravdas1981]

​@@PhdHungপ্লিজ ভাই আমাকে সার্কিট ডায়াগ্রামটি দিন

[@seema.k2002]

One thing I'm unable to understand is, battery gives 12V DC, 6 transistors/Mosfets amplifies the Voltage and transformer transforms the amplified Voltage to 220V but which component converts DC to AC? Correct me if I'm wrong.

[@at190.corona2]

If it is a different number, use the r value.

[@shakirkhan-or2zk]

This is really amazing but can u tell me if I use 100w light and 100amprie battery how time will it run

[@at190.corona2]

If the MOSFET has a heat problem, how to solve it? Please conclude that this circuit is how much frequency.

[@bikashchandrametia712]

There will be heating problem because there is 6 to 10 amp is flowing through so that can only be solve by using good quality thermal paste and good quality heatsink which is made for CPUs

[@0HYEAH]

Attach a 12v DC fan to the heatsink

[@sundaramurthig2813]

Very good Sir. Show the diagram please, unless it's no useful for learners. Video is incomplete without diagram.

[@ThomasAlbertDecker1973]

Where the capacitor is connected. The diagram does not appear.

[@PhdHung]

12V filter capacitor, you connect capacitor to + - of 12V battery

[@petrucorciu1967]

Y otros 2 cables como se conecta la bateria

[@gabrielbezerra8618]

Capacitor in paralel with the battery...

[@Vtelix]

It looks like that my question was not posted, so am postin in this reply: Hi ! I have three "simple" questions :-). 1.) My input source is alum battery and output of this kind of battery is cca 11 - 11.5V. What do i need to change so i can use your setup ( as end solution i can add some step up circuit but maybe there is a simpler solution ). ---------------- 2.) I need to wind new transformer for your 1KW setup, can you tell me specification of this new transformer ( please take notice of lower voltage input ). --------------- 3.) Can you suggest somekind of protection ( overvoltage, overcurrent ) i can add to your setup ? If something goes wrong , shourtcut etc. This is very interesting project and I would have knowlage I would add some LED on/off signalisation, protection and some simple BMS... Anyhow, very interesting and I am planning to create one. Thank you for your time and answers !

[@sreejithtg8562]

Can you share transformer connection details. I made circuit with diagram but its not working. Please help me.

[@sundaramurthig2813]

Thanks for nice video Sir. Please show diagram also which will helpful to us. Please please please diagram. Once again thanks.

[@PhdHung]

Project file in video description

[@doomsanpabling]

why it has a jumper where is the primary and aecondary?????

[@silvialuca7066]

Download files

[@nihalweerakoon944]

No 1 👍👍👍👍👍👍👍

[@PhdHung]

thanks bro

[@MyOwntuahur]

Pure sine or no this inverter

[@youall21]

I think this pure shine.. coz it can use to power a drill

[@ericscaillet2232]

Unless you check it with an oscilloscope one is guessing ,the drill test is not confirmation ,but surprisingly it works - well done!

[@luigiromano1484]

Thank you Homemade 102 for sharing your knowledge. The diagram link in the video description does not work. Could you please correct it?

[@PhdHung]

Yes, I will fix it

[@luigiromano1484]

@@PhdHung THANK YOU!

[@antonioestigoy3082]

Sir Romano, have you received the Schematic Diagram for Inverter Homemade 102? May I request you to send it to me also, Thank you.

[@sukhboparai6266]

Nice sir

[@PhdHung]

Thanks for watching

[@electroniquepassion]

Nice 👍

[@PhdHung]

thanks bro.

[@saifsaimum1190]

Bro plz tell me ,can I use 5 amp transformer??

[@PhdHung]

yes, u can

[@irasundan8050]

thanks for sharing your knowledge, thumbs-up , more power....

[@PhdHung]

Thanks

[@xuanquy3009]

Mạch tự kích này tần số ra bao nhiêu vậy ad

[@PhdHung]

with standard transformer 12 0 12. Frequency is ~ 50Hz. change primary to change frequency.

[@xuanquy3009]

Cảm ơn ad

[@ramirocebreros5299]

Well, the file or diagram does not include the electrolytic capacitor, I would greatly appreciate clearing my doubt since I plan to make one equal to the one in the turotial I thought it was fantastic

[@saanjayray]

can we use 24-0-24 8ampere in this circuit .

[@PhdHung]

no. u need trafo 12 0 12

[@djdayvi961]

Thanks for the circuit diagram!

[@sidharthshukla4290]

Sir is circuit me 12.0.12 ,5 amp ka transformer kaise connect karayein.sr pl suggest soonly.

[@roshanthapa6169]

bakbas mumara kamdhanda nahin he?

[@roshanthapa6169]

battery connection kaha se aaya capacitor kaise Mora?

[@gastonvillarino]

Excellent! What sine wave we have at the output?

[@DL-kc8fc]

It's pulse. No sine wave. Surprisingly, the drill works for this, because harmonic oscillations and a non-circular rotating magnetic field are created.

[@diegocampos8373]

E esi capacitor é d quantos mf e os volts ??

[@diegocampos8373]

Descupa eu acabei d v n vidro agora

[@PhdHung]

12V filter capacitor. You can use 2200uF 25V

[@minditon3264]

do we use IRF 3710 instead of IRF 3205

[@PhdHung]

ok bro

[@minditon3264]

@@PhdHung I have 20 IRF 3710 .Can I use 10+10 instead of 3+3.

[@МихаилИванов-в2в]

Ok ! 👍😎

[@raulgutierrezdev2398]

excellent video¡.......if i want to build 12v. dc to 125v. ac. 2000 w ...how could? i apreciate your answer

[@PhdHung]

You need bigger transformer, primary 12V 0 12V, secondary 120V. Can use 10 mosfet.

[@jhossanantonio557]

You have 20 Like me on my part others will be interested

[@PhdHung]

[@jhossanantonio557]

@@PhdHung When you have time I want you to make a video of this circuit with the wave identifier of the current to know if it is sinusoidal or square wave

[@jhossanantonio557]

@@PhdHung With the oscilloscope

[@amritpal5032]

Very good 👌

[@PhdHung]

Thanks bro

[@fernandodeleon8984]

Que función cumple el filtro

[@PhdHung]

It helps to stabilize the voltage

[@fernandodeleon8984]

@@PhdHung lo pongo en paralelo con la batería?

[@fernandodeleon8984]

@@PhdHung Hola use los irfz44n use 6 pero quiero aumentar le la frecuencia

[@Rareislive2]

Battery charg automatically in this projects????

[@PhdHung]

no.

[@dainbermudez8676]

Me sirven mosfer de referencia RFP50N06

[@vidyasagar3651]

Sir hath se banaya hua inverter achha rhta h ya company wala.. Plz suggest me.

[@PhdHung]

Sorry . I don't understand

[@huutrihuynh5164]

10v 0 10v ok

[@PhdHung]

ok, but the frequency will be larger than 50hz, maybe ~ 70> 100hz.

[@nasirkhan2875]

Nice concept dear. Whats is the output wave form?

[@PhdHung]

is square wave.

[@youzhang4814]

Do it really work?????? I'm doubtful about this simple inverter with only mosfets! You must do it again without adding and cutting in the video.

[@PhdHung]

It uses ZVS driver. Look for it on google.

[@sanctuaryjames3434]

Thank you very much. You're good. I made it and it works. thanks. I want to use it to back up my sound system. Can I use it with Sound Power Amplifiers and mixing console?

[@ajitsarkar5714]

IRF3205 n or p which one u use?

[@dumahlophe7732]

Can your share your scheamtic diagram

[@demiandhartono1042]

Can other electronics be used like TV & how many hours of battery usage?

[@PhdHung]

It can be used for all electrical equipment. For example you have 1 100Ah-12V battery. It can provide a maximum of about 1000W. The efficiency of this inverter is about 75%. If you use a 100W light bulb. You can use in 7.5 Hours.

[@MuhammadAli-fx2qu]

Very good👍👍👍👍👍👏👏💗🌷🌷

[@PhdHung]

thanks bro

[@ahmedredaa.r.m70]

In principle, I live on the wonderful video and on your explanation of the electronic components in it, but the problem is that you are shown the way to connect the electronic components and also shown how to wrap the electric adapter and the size of the slide and the length of the tongue of the slide means you are to present a video tutorial Zaidh be explained every need in it if possible Code of winding transformers designed for interferometers I hope attention and reply

[@aurosdjapna61]

Not warking

[@carlosalbertopereira7032]

oi boa noite! pode ser colocado os 6 mosfet no mesmo dissipador de calor?

[@PhdHung]

You need an insulating silicon sheet

[@peterchau8299]

Can someone explain. How long the Batterie last until it will be empty? Do we need every time to change the Batterie after is emty for this Project? How it works…? Thanks for the Explanation...

[@PhdHung]

Working time depends on your battery capacity and load power.

[@peterchau8299]

Thank you so much for your respond. Very appreciated!

[@SrinuSrinu-ry9wq]

Good, but I couldn't understand connection, can u draw on paper? Please. And also which type of transformer is used?

[@gabrielbezerra8618]

Thank you i did it..., but i have some other questions like : 1 - if i add more mosfets and a transformer with more amps i can have more watts ? 2 - if i add more mosfets i can use more voltage, amperage or both ? 3 - this project can use a car battery ? ( 12v 75Ah )

[@PhdHung]

Yes, if you use bigger transformer, more mosfet, you will get bigger capacity. You can use 75Ah car battery

[@belajarilmu2009]

what is the black cable that across at the middle of the transformer?

[@PhdHung]

nothing, it just connects 2 points of the 12V 0V ,12V 0V transformer to 12V 0 12V

[@belajarilmu2009]

@@PhdHung Oh, thank you..

[@vishalunawane335]

Sir can we use 9 0 9 transformer Sir please reply

[@vishalunawane335]

Sir please reply sir

[@PhdHung]

no. u need trafo 12V 0 12V

[@vishalunawane335]

Thanks for your kind response

[@creativeboy5846]

Bhai isska running time kitna rahega, matlab kya ham issko non stop chala sakte hai. 5-6 hours tak

[@aashiqurrahman329]

Thanks a lot bro....can i use 600 va transformer in this inverter....I got this transformer from ups....Hope you will give a reply

[@carlosalbertopereira7032]

oi parabéns muito legal , consegue fazer o mesmo projeto com o 12 mosefet irf3205 ,? ficaria com 2000w? sucesso e que Deus continue te iluminando vc e sua família hoje e sempre abraço.

[@LucasPereira-be8il]

como liga os doze transisto

[@eynhos]

چقدر تو باشعوری! کاش همه مثل تو بودند.

[@Abouadam3851]

Good job ! Plese why i have 350v in out?

[@kanjibhaidesai8893]

Jordar 👌idia is supper 👍

[@prafulgotefode551]

What type of mosfet are used. P channel Or N channel

[@prafulgotefode551]

Please reply me

[@PhdHung]

N-mosfet. U can use irf 3205, irf z44n etc...

[@srbrocard84]

Excellent, good power and simple

[@PhdHung]

thanks bro

[@chunilalgajera598]

Aap joinveter banate Dikhate ho bars bar Ek dam saf tarike Bataiye jise samjme Aaye.or uska dayagra. Bhi balek markar se baniye Jise bara bar dekh sake. Dhnnyvad,🌹👍🙏

[@yusufmuwahhidh.wonggo9477]

Bro, Can I use irfz44n mosfet and transformer used ups?

[@PhdHung]

yes. ok bro

[@yusufmuwahhidh.wonggo9477]

@@PhdHung Is this real 1000 watts??

[@jabarsingh712]

Is ki frequency naap kar batao please isme konsa transformer lagaye 12-0-12 laga sakte 30amp ka or kitni frequency hogi

[@philipobinna8062]

Pls can i use 2200 capacitor 50v instead of 25v you used?

[@PhdHung]

yes, ok

[@christian-u5i7f]

Great technical used here