I think that IC has got damaged due to snubber diode failure.
@HaseebElectronics9 ай бұрын
might be, most of time snubber diode failure causes to saturate the core and creates spikes, that also cause to increase in vcc voltage that may be a reason for IC failure. otherwise these chips are most failure items and sometimes snubber diode failure cause to damage the mosfet as well
@Somanathan-hj7ge9 ай бұрын
I don't know how people are giving likes, with out seeing video and your job sir, your video are real and great,so 😊I think
@HaseebElectronics9 ай бұрын
Thank you so much
@jackshuler31269 ай бұрын
Thank you for sharing your knowledge on smps. I have learned so much from these videos.
@Somanathan-hj7ge9 ай бұрын
Yes, sir,i watched the video 😊, super soldering iron tip, temperature perfect, good ic removing technic, super cleaning ic holes with wick,and using alcohol, awasome job. you are wonderful 😊 very very good 👍
@HaseebElectronics9 ай бұрын
best regards and special thanks
@Somanathan-hj7ge9 ай бұрын
Okay Bhai
@gopalarao85789 ай бұрын
Hi brother namaskaar. Your soldering iron is very nice. Thank you for sharing this video. Good night 🙏
@Watch__This_9 ай бұрын
Great videos, you are a great teacher ❤, one time in psu that ic was in kilo ohms and in the end i have changed and it start working, strange but it happens...
@gauripartapshanker91979 ай бұрын
Informative and knowledgeable vedeo. Thank you so much God bless you.
@TheVinylrider9 ай бұрын
Thank you very much for your effort to teach us and share your knowledge.
@GSimon8509 ай бұрын
brilliant video many thanks for sharing.
@ISO07ISO9 ай бұрын
Senden öğrenmeye devam ediyorum. Geçmiş videoların tümü Türkçe olsa çoook sevineceğim. Tekrar tekrar izliyorum.👏👏👍
@merwynvincent3 ай бұрын
Just what I needed!!! Thank u!!
@HaseebElectronics3 ай бұрын
You're so welcome!
@francomongillo6 ай бұрын
Sei un grande, veramente bravissimo e grazie per i video che ci regali ogni volta si impara sempre qualcosa.Grazie.
@muhammadishtiaq249 ай бұрын
Excellent thanks for sharing this informative video
@HaseebElectronics9 ай бұрын
My pleasure
@otabektillavayev33099 ай бұрын
Assalomu alaykum Best Teacher my
@mokhles54yt5 ай бұрын
Dear Sir, kindly mention if you have time, what are reasons might be the cause of voltage down from 5v to 1.4v of pin8 of IC 3844? no need details explanation. only mention in very short technically to spend less time to reply or you can reply during any next video to save time. I am from Bangladesh. my age is 70. I enjoyed your all videos like short film. I am also technical person.
@moniruzzaman85687 ай бұрын
Sir advice acro power supply 24v 10a full repair video 3844GM -E1 ic is damaged
@victora71973 ай бұрын
Thanks for the video, I have similar SMPS and its IC is also damaged but the IC No is 1203P60 and unable to find same ic, so please suggest me a alternate or substitute IC
@mahmoodh77676 ай бұрын
Perfect 👌👌👍👍🙏🙏
@amma18379 ай бұрын
Thank you sir
@anishstechlab73239 ай бұрын
Super explanation
@HaseebElectronics9 ай бұрын
Best regards 💕
@Edmorbus9 ай бұрын
Thanks for another great video
@rajkhumar0019 ай бұрын
Nice work sir. Sir i have a doubt. You have another to check the switching. Inthis case how can we check the switching ic if i dont have any another smps? Thank you🙏
@HaseebElectronics9 ай бұрын
please check video number 975 for testing switching of smps ic
@rajkhumar0019 ай бұрын
@@HaseebElectronics thank you sir for your reply I will check it. 🙏
@sinhrr4 ай бұрын
Kindly explain the principles involve which you came to conclusion thst IC is short. What you checked pin no 7 & ground resistance kindly explain so that we can learn
@sinhrr4 ай бұрын
Also kindly mention the soldering iron u are using it is very pointed & good plus multimeter brand which multiple functions
@jboy4real9 ай бұрын
Kindly assist I have a big challenge to power up the uc3842 I want to design a DC to dv buck converter with a minimum voltage of 36v and maximum is 100v I watched your video on start up resistor for uc3842 after adding my calculated resistor value the voltage at pin 7 is only 8v hence can't power the IC . I need your support. Thanks
@mahmouedsayem5 ай бұрын
ممتاز ❤
@josephnkhaikolungu8943 ай бұрын
How are you Sir I am having a challenge with a component labeled STPS30100ST, DKLLD, CHN 950. I am not sure if it's a Schottky diode or a voltage regulator, 3 legs
@thusharasampath30299 ай бұрын
Sar. We can use the 230v led bulbe.. ??
@HaseebElectronics9 ай бұрын
no. we need 100 watt or 60 watt tungsten filament lamp
@thusharasampath30299 ай бұрын
Ok sar...🫡🫡🫡
@dipakbhalodia71559 ай бұрын
Bootstrap capacitor ka video urdu chennal me kab ayega
@HaseebElectronics9 ай бұрын
it is already uploaded on urdu channel
@Radek__9 ай бұрын
14:45 I think you should regulate it to 12.00V, ONLY when you have some load connected. otherwise you set it to 12.00 without load, but then when you connect someting it will drop down.
@remediusfernandes15709 ай бұрын
Thanku sir🙏
@HaseebElectronics9 ай бұрын
most welcome
@TheDurdane9 ай бұрын
If you put the wick in flux, it will work better...
@SamuelGirma-fp6smАй бұрын
I have smps and its output is 32v and 15v but it stop working ,when i check the connectivity between 32v and ground the multimeter beeps which is there is short circuit i replace all the component except az 437 transistor what is the problem and the ac part is ok
@jcsudeshchannel82249 ай бұрын
Good
@mdiqramhossain94938 ай бұрын
How could I find the model wise SMPS schematic diagram for print out?
@navalsharma80349 ай бұрын
What is value of diod F4
@HaseebElectronics9 ай бұрын
it depends on package code if it is SOD523 or SOD123 package from Philips and Central Semiconductor, is 3.3 volt zener same marking and same package code from Luguang Electronic Technology / Vishay Semiconductor / Taiwan Semiconductor Company is 36 Volt zener SOD323, SOD123, SOD523 package from Comchip Technology if for 9 volt zener please confirm the package style in your circuit
@chumatez6 ай бұрын
How do you know when the ic is bad
@HaseebElectronics6 ай бұрын
there are many sypmtoms that indicate the fault location
@M.lababidi9 ай бұрын
Alsalam Alaikom. I have a power supply that has a strange malfunction, which is that there is a 24 volt output, but there is no amp... and I need help, please. 😢😢😢
@isaacattigah55959 ай бұрын
🫡🙏🏻
@dafaabdillah7303 ай бұрын
Jangan pake bahasa Inggris gak faham lo
@HaseebElectronics3 ай бұрын
Selamat malam. Saya mengerti sedikit bahasa Inggris, dan saya mencoba untuk berbicara dalam bahasa itu. Saya juga akan mencoba untuk lulus ujian bahasa Inggris. Namun untuk saat ini mungkin ada yang bisa memahaminya dan bisa mengambil manfaat darinya. Selain itu saya berbicara bahasa ibu saya dengan sangat baik, yaitu bahasa Urdu. Anda dapat mendengarkan saya di saluran bahasa Urdu saya www.youtube.com/@haseebelectronicsurdu
@damensutherland70819 ай бұрын
Tuff transistor
@Kevin-mp5of9 ай бұрын
I believe placing the diode on the bottom of the circuitboard will cause poor heat dissipation and premature failure.
@kaizen10719 ай бұрын
Emeğinize sağlık efendim.Vakum istasyonu nu kullanmadınız. Sevgi saygılar sunarım.
@MohammadhosseinRezabeklooКүн бұрын
Very informative
@rohanranjandesilva4659 ай бұрын
Gwt40hp65fb sir can u tell me any equal one please thanks
@mudasirnazir41349 ай бұрын
Jazakallah sir very very good teaching❤❤❤❤❤ By the way where is your solder sucker station you are using normal soldering iron
@JayWye526 ай бұрын
you can see his desoldering iron at the top of the video,the turquoise handled Weller. maybe it was full or clogged so he went to solder wick.
@aknkurk36449 ай бұрын
Aleykum selam, Again, it was a very informative video, you are doing great work.,thanks
@HaseebElectronics9 ай бұрын
welcome
@Repairing-y9y9 ай бұрын
What is your checkin light..led or haligon bulb
@HaseebElectronics9 ай бұрын
it is 100 watt tungsten filament lamp
@rolanddejesus86859 ай бұрын
thank you very much...God bless.
@HaseebElectronics9 ай бұрын
You are so welcome!
@nuritepegoz60429 ай бұрын
verdiğin bilgiler için teşekürler ALLAH C.C Razı olsun
@susantaatha64689 ай бұрын
Very nice information. Thank you sir.
@HaseebElectronics9 ай бұрын
Most welcome
@Somanathan-hj7ge9 ай бұрын
Let me see video after 43 minutes,
@HaseebElectronics9 ай бұрын
it is my pleasure
@aliemlek9 ай бұрын
👌👌👍👍
@HaseebElectronics9 ай бұрын
thanks a lot
@mustafakaragol95309 ай бұрын
@HaseebElectronics9 ай бұрын
best regards and special thanks
@JAMMYKAN9 ай бұрын
Good job 👍🏻 ❤❤❤
@osamakosara9 ай бұрын
God bless you sir, so much useful techniques when you test the resistance between - the bulk capacitor and the pin 7( VCC ) it is awsome
@mohamedantri94339 ай бұрын
كالعادة استاذي الفاضل أشرف الله يحفظك من كل سوء ويحفظ حسيب على معلوماتك القيمة وجعله في ميزان حسناتكم استاذنا ❤❤❤❤