12V Softwash Pump Setup

[@allproexteriorservicesllc5338]

Tim, I hope all is well. Great work on the 12 volt set up. I agree with you that the 12 volt has its place. Wash on brother!!

[@ExpertPowerWash]

Thank you! Hope you are off to a great season!

[@DavidSunshineAquaWash]

Well done! I like the design and build.

[@ExpertPowerWash]

Thank you!

[@carpetmagicofwilson]

Great video, I run a 12 volt setup, it has 7gpm 100 psi pump, i'm noticing when i pull the trigger i get my full distance then within 5 seconds or so my distance drops about 6 or 10 feet, it has 1/2" hose on the reel. coming out of my metering system is a 3/4" hose feeding the pump, i have 1/2" water line and 1/2" bleach line going into the metering valves. Any ideas Thanks

[@ExpertPowerWash]

Sounds like air in the line for sure. Go through every single piece of your plumbing.

[@ktpowerwashing]

That set up sure looks familiar. Keep up the good work. Enjoy your vids.

[@ExpertPowerWash]

Thanks, will do!

[@nick32141]

So if you were using this pump three times a week and flush them out how long do you think these will actually last what’s your experience?

[@ExpertPowerWash]

It would vary. I’d be happy with 3 months.

[@nick32141]

@@ExpertPowerWash Does the Remco 7GPM need to be adjusted when first set up with the small star key? Thanks.

[@salscavo3110]

Great video. When will you have more available? It shows out of stock on your website.

[@ExpertPowerWash]

Waiting for a delivery.

[@austinbarnes5476]

Tim I’m running a shurflow 5.3 90 psi I have a 3/4 inch intake hose running to solution to 3/4 inch feeder hose to a 3/8ths hose reel manifold that had 100 ft of 5/8 flexzilla with a Softwash gun off Amazon the blue gun 16 gpm …I have a hard time keeping that pump with consistent pressure it’s almost like the pressure builds great but as soon as I spray it can’t keep up anything to. Change?

[@Thetruthhurtstrump2024]

Does it damage the pump leaving this outside in the elements?

[@ExpertPowerWash]

Not at all. Just don’t let it freeze which is pretty standard would everything.

[@Thetruthhurtstrump2024]

@@ExpertPowerWash I’ve been told from others that the pump should be upside down? Is this correct?

[@hfdg3]

Can you tell me where I can find that rocker switch? Thanks

[@ExpertPowerWash]

We sell it. pressurewashingskids.com/products/soft-wash-12-volt-switch?_pos=3&_psq=Switch&_ss=e&_v=1.0

[@RickHamilton-nk5pi]

Tim, when you guys set these up on your rigs what size plumbing do you use coming into and out of the pumps? Great video!

[@ExpertPowerWash]

3/4 from the mixer to the pump. 1/2 out. You have to remember the pump is 1/2 and so is the hose reel. I’ve tested other options and we land back at this for the best all around performance.

[@RickHamilton-nk5pi]

@@ExpertPowerWash Thank you, Tim.

[@ktpowerwashing]

​@@ExpertPowerWashspraying with 1/2" hose or 5/8" hose? Your comment leads me to think 1/2", keeping everything consistent with pump outlet size, hose reel in/out.

[@jerrymeyers2075]

Do you sell this setup on it's own?

[@ExpertPowerWash]

Yes I do. Here’s the like, pressurewashingskids.com/products/mounted-remco-5-3-gpm-60-psi-softwash-pump?_pos=3&_psq=Pump&_ss=e&_v=1.0

[@jerrymeyers2075]

@@ExpertPowerWash thanks for the quick response I'll be ordering one next week

[@mr.skeptical3071]

I thought that a 5.5 12vollt would be way faster flow than a 4gpm gas

[@ExpertPowerWash]

Well it's pushing more GPM but it's only 100 psi but your average 4 GPM Gas might be pushing a little less water but it is also 4000psi