(14) طرق حقن التربة - Soil injection grouting

SOIL STABILIZATION BY INJECTION of GROUTS :
Grouting is a process whereby fluid like materials, either in suspension, or solution form, are injected into the subsurface soil or rock .
The purpose of injecting a grout may be any one or more of the following:
1. To decrease permeability.
2. To increase shear strength.أ .
3. To decrease compressibility.
Forms of injection grouting
permeation grouting
jet grouting
Compaction grouting
Fracture grouting
Suspension-type grouts include soil, cement, lime, asphalt emulsion, etc., while the solution type grouts include a wide variety of chemicals. Grouting proves especially effective in the following cases:
1. When the foundation has to be constructed below the ground water table. The deeper the foundation, the longer the time needed for construction, and therefore, the more benefit gained from grouting as compared with dewatering.
When there is difficult access to the foundation level. This is very often the case in city work, in tunnel shafts, sewers, and subway construction.
3. When the geometric dimensions of the foundation are complicated and involves many boundaries and contact zones.
4. When the adjacent structures require that the soil of the foundation strata should not be excavated (extension of existing foundations into deeper layers).
Grouting has been extensively used primarily to control ground water flow under earth and masonry dams, where rock grouting is used. Since the process fills soil voids with some type of stabilizing material grouting is also used to increase soil strength and prevent excessive settlement.
Many different materials have been injected into soils to produce changes in the engineering properties of the soil. In one method a casing is driven and injection is made under pressure to the soil at the bottom of the hole as the casing is withdrawn. In another method, a grouting hole is drilled and at each level in which injection is desired, the drill is withdrawn and a collar is placed at the top of the area to be grouted and grout is forced into the soil under pressure. Another method is to perforate the casing in the area to be grouted and leave the casing permanently in the soil .

[@rizanrizan5669]

شرح ممتاز من مهندس عبقري

[@mahmoudgeo2782]

حبيبى ربنا يبارك فيك وكل عام وانتم بخير

[@VinCivilWorld]

Very good one....

[@mahmoudgeo2782]

Thanks alot

[@mohamedabdelnaeem6381]

شرح ممتاز يا هندسة انا شغال علي حقن التربة بالبولي يورثان فوم يا تري اشتغلت في الموضوع دا قبل كدا ؟

[@mahmoudgeo2782]

ابعت لى تليفونات حضرتك للتواصل

[@mohamedabdelnaeem6381]

@@mahmoudgeo2782 ممكن رقم حضرتك يا هندسة

[@mohammedlasmi649]

يا هندسة. طريقة grouting compaction يمكن أن ترجع المبنى الماءل إلى وضعه الافقي قبل النزول؟ شكرا

[@mahmoudgeo2782]

اهلا مهندس محمد جاوبت على سؤال حضرتك فى التعليق فى الحلقات الخاصة بمواد حقن التربة والخوازيق الابرية . لو حضرتك موجود فى مصر ممكن تتصل على التليفونات الآتية ومتواصل ، وندرس المبنى ونشوف الحلول المثلى لتثبيت الميل وتحسين خواص التربة إن أمكن ٠١٠٠٦٠٤٤٦١٤ ٠١١٢٥٧٣٤٤٤٧

[@VinCivilWorld]

Suscribed..

[@mahmoudaboushanab968]

ممكن موردين مكن حقن التربة بالسعودية

[@mahmoudgeo2782]

أهلاً بحضرتك باشمهندس محمود إذا وجدت شئ سابلغك إن شاء الله