#179

[@Homer19521]

I also noticed the manual error. Great job on a great radio. I had one with all the options and new ceramic trimmers were already in place. Nice to look at also.👍

[@davidv1289]

Nice to have a relatively easy repair ocassionally. I just completed repair of an HP 3468A multimeter that needed a negative 15 volt regulator IC, capacitors, and a NVRAM battery plus calibration. Always satisfying to bring a piece of equipment back to life! Thank you for sharing this repair with us. Regards, David

[@dl7majstefan753]

Tnx dr David. Yes and the mount trash is a little big smaller....hi.

[@ckm667]

Many thanks for the video, very informative and useful. 73's

[@Joe_KS1I]

Great job Stefan! I always learn something when I am watching your videos. Also , I used to have a IC-751A , but sold it in 1988.

[@TheRadioShop]

Great repair job! good to see these old rigs brought back to life.

[@dl7majstefan753]

Mni thanks!

[@berndb.5097]

In my experience, when repairing ICOM devices from the late 70s to 80s, you spend a lot of time looking for cold solder joints and particularly bad PCB through-holes ;-) But thank God everything can be repaired. Anyway, thank you very much for your nice video Stefan. 73 de Bernd DF7PI

[@dl7majstefan753]

Aber insgesamt ist dieser TRX bzgl. Durchkontaktierungen nicht bekannt für Probleme; scheint dass ICOM das da schon im Griff hatte.

[@JJ-el8li]

Excellent video. I'v repaired a few of Icom's from this era as well.. I still own a 751A and it is great condition.

[@dl7majstefan753]

This oldie is still very competitive to new rigs

[@christianries4717]

Hi Stefan, nice Video and good work. I finished my IC751 today. At least one trimcap was faulty. For completeness I also changed the BFO Plastic Cap to a ceramic one. Now a full calibration is planned next shacktime. The Rig is still competitive imho.

[@dl7majstefan753]

Yes, these old analog TRX are still very well operating!

[@mikefinn2101]

Stefan where did you get the trimmer caps? I have a 751A I may need to replace mine

[@dl7majstefan753]

I was brave enough to by them on a famous platform. The value doesn´t need to be spot on - some pf more are not critical and you´ll see if the setting range is not correct.

[@tlrptg]

at least this project was easier for you. I am currently working on an Icom IC-730 which was damaged by lightning, HI :))

[@Team-fabulous]

Superb video Stefan.. My 751A suffered the same issues and I repaired it exactly the same as yourself...

[@dl7majstefan753]

Good ideas reproduce themselve - TNX

[@a1aman]

Did the VCOs on my IC735 several years ago. Replaced with ceramics. Had a fine CW ragchew with it today after sitting idle for awhile. Danke Stefan.

[@Vinni315]

I also had an IC-751A. Excellent device. There was one problem with it - the vacuum indicator stopped working. I found a couple of bad solders and everything works again. I made a new RAM board for him. And now I don’t have to worry about having a dead battery! I also made an analogue of the UX-14 interface module. And the transceiver now has CAT! Unfortunately, due to the Russian attack, I had to leave all the equipment there and save the family more than 1000 km from home.

[@dl7majstefan753]

Hope all is OK now for you and your family which is much much more important than any equipment. All the best!

[@Vinni315]

@@dl7majstefan753 Thank you. We are now in a relatively safe place. There is no complete safety anywhere now.

[@Дава-м9к]

​@@Vinni315если не секрет откуда ты ?

[@Vinni315]

@@Дава-м9к не секрет. А в чем вопрос?

[@Дава-м9к]

@@Vinni315 Да просто вопрос в самом вопросе UB5INZ.

[@ROURE19572]

Bonjour Stefan, j'ai le même problème avec le Ic 751, dans la partie PLL, mais en France il n'y a pas beaucoup de réparateur compétent. Hello Stefan, I have the same problem with the Ic 751, but in France there are not many competent repairer, thank you for this good video

[@dayleedwards3521]

The pitch difference with USB/LSB indicates a small asymmetry with the IF filters, very common and usually only noticeable with off signal broadband noise.

[@dl7majstefan753]

True, this effect is common for analog filters; but a short check of the BFO can´t be wrong....

[@Greg-et2dp]

DL7MAJ STEFAN YOUR KZbin VIDEOS ARE AWESOME MY FRIEND

[@wayner-model5880]

Great video. 👍🏻

[@Greg-et2dp]

DL7MAJ STEFAN YOU ARE GOOD AT RESTORING VINTAGE SHORTWAVE RECEIVERS AND ALIGNMENT OF VINTAGE SHORTWAVE RECEIVERS AND RESTORING HAM TRANSCEIVERS MY FRIEND

[@franciscolopez3229]

Sir, someone is selling the Japanese version ic 750a which is an untouched never been used New Old Stock as they say. How many years do you think it will still last? And in your honest opinion, do you think I should buy it? Thank you so much.

[@dl7majstefan753]

Sorry can´t answer this, but such old units are a permanent source of work; so buy it if you need additional work.

[@rinobilleri1464]

Hi stefan...how disconnettere the ribbon flat cable in order to manager the board VCO

[@dl7majstefan753]

The connector has a lock, which can be unlocked (=lifted) by the two flaps on each side of the cable/connector. Don´t forget to lock the cable vice versa after the work; otherwise you´ll create a new problem over the ime...hi.

[@Дава-м9к]

​@@dl7majstefan753Здравствуйте, как думаете если подать питание 15 вольт , не сгорит ???

[@Greg-et2dp]

DL7MAJ STEFAN THE OWNER ICOM IC-75 IA HAM TRANSCEIVER IS AWESOME MY FRIEND

[@Greg-et2dp]

DDL7MAJ STEFAN I LIVE IN NORTH AMERICA I PICK UP IOT OF MW STATIONS MY FRIEND

[@Greg-et2dp]

DL7MAJ STEFAN MY HOBBIES ARE PAINTING PICTURES AND LISTENING TO SHORTWAVE AND SSB IAM THINKING ABOUT GETTING MY GRMS LICENSE

[@Vinni315]

I also have an IC-751A. Excellent device. There was one problem with it - the vacuum indicator stopped working. I found a couple of bad solders and everything works again. I made a new RAM board for him. And now I don’t have to worry about having a dead battery! I also made an analogue of the UX-14 interface module. And the transceiver now has CAT! Unfortunately, due to the Russian attack, I had to leave all the equipment there and save the family more than 1000 km from home.

[@dl7majstefan753]

Hope all is OK now for you and your family which is much much more important than any equipment. All the best!