1966 to 1977 early bronco tailgate and handle assembly (Tailgate assembly) Episode 6

In this video, you’ll learn How to build 1966 to 1977 early bronco tailgate and handle assembly ? (Tailgate assembly). This is Episode #6.You can watch previous episodes by checking links below. I hope you will love this episode. If this video has given you some value then make sure you have smashed the like button and if you are new to our channel then make sure to subscribe the Channel and press the bell icon to get notified on any update we release. Thanks!
❤Subscribe ►bit.ly/2J4ePC6
****************************************
❤All Episode's Links:-
Episode #1👉kzbin.info/www/bejne/gJane2ebm9ileqc
Episode #2👉kzbin.info/www/bejne/aanIYmSdetOUps0
Episode #3👉kzbin.info/www/bejne/m4a0aZqFa6qaf7M
Episode #4👉kzbin.info/www/bejne/rYK4pIhnn82ebcU
Episode #5👉kzbin.info/www/bejne/ep_Mepd5fq6Cb9E
Full Playlist 👉kzbin.info/aero/PLB5PfYfsmTebjCB0eSzlv_kEB1Jk4-9Gt
❤Shop Equipment:
MILLWAKEE TOOLBOX👉amzn.to/34Idmd0
MIG WELDER👉amzn.to/2TyTpip
MILLWAKEE TOOLS👉amzn.to/35LGaAy
MILLWAKEE GRINDER👉amzn.to/37TeJr7
RED TOOL CART👉amzn.to/35T6ngK
SHOP MAGNET FLASHLIGH👉amzn.to/34GmaQz
❤Camera setup:
VLOG CAMERA👉 amzn.to/3jHbEwv
GOPRO HERO 8👉amzn.to/2TEq4CZ
MICROPHONE👉amzn.to/2HNrglh
CHEAP KNOCK OFF GOPRO👉amzn.to/3mAXoY9
CAMERA LIGHT👉amzn.to/3mAsSgT
CAMERA MOUNT👉amzn.to/3e92Ka0
SUCTION CUB CAMERA MOUNT👉amzn.to/34KI3hL
VLOGING HANDHELD STAND👉amzn.to/3ebRycx
LARGE CAMERA STAND👉amzn.to/3mAXoY9
VLOGING BACKPACK👉amzn.to/31VxrKK
MEMORY CARDS👉amzn.to/3eaKmxq
💡CONTACT INFO:
[e-mail]
mbimotorsports
mbimotorspo...
#earlybroncotailgateandhandleassembly #Tailgateassembly #MBIMotorsports

[@lorenzorodriguez2700]

Thanks for sharing!

[@craigmaverick]

Great info! I covered the end of the latch rods with heat shrink to help eliminate any rattles with the latches.

[@blucheer8743]

Good idea

[@blucheer8743]

Connect the rods first to the butterfly toggle then bolt it to the handle

[@josephbeltramini5442]

Great job! What about the two center bolts/nuts that are in the bucket handle? Mine were rusted out.

[@jakeellis2149]

Same question!

[@gennaodis7861]

Nice job. Can you get these internal parts used any where? Thanks

[@lorenzorodriguez2700]

Can you give me the tailgate length? I'm putting one together and don't have a gate, yet. Right down the middle will work.

[@TheFrenchbull2]

How much do it cost and where to get

[@jakeellis2149]

LMC truck

[@robertdavis6708]

@@jakeellis2149 Toms Bronco, Jeffs Off-road Bronco, Wild Horses bronco.