1974 CHEVROLET CHEVY CHEYENNE PICKUP TRUCK COMPARED TO FORD RANGER BLAZER SUBURBAN & VAN 17764

Want to support this channel and help us preserve old films? Visit / periscopefilm
Browse our products on Amazon: amzn.to/2YILTSD
Chevrolet Trucks 1974 Pickups Comparison. This is a 1970’s era, color movie about comparing Ford and Chevy Half-ton pickup-trucks. Both trucks are equally equipped. C10 Chevy Fleetside Cheyenne Super and an F100 Ford Ranger XLT. Man enters the frame and speaks to the camera. Chevy pickup is loaded with a palette loader, 1:00. Chevy pickup is loaded with a palette loader, 1:15. Chevrolet massive girder beam front suspension, 1:35. Ford I-Beam design, 1:43. Ping pong ball test, 2:11. GM proving ground, 2:20. Ping pong ball test comparison, 2:50. Pickups are lifted by cranes to pick up trucks and compare spring capacities, 3:37. Axles are compared, 3:55. Shielded versus unshielded shock comparison, 4:28. Mufflers and tailpipes, 4:39. Chevy and Ford front and rear fenders, 4:55. Fender liners, 5:30. Man opens the hood of the Chevy, 5:50. Cut side view of the roofing panels on the Chevy and Ford sound reduction and structure are shown, 6:07. Comfort tilt steering on the Chevy, 6:54. Ignition locks are compared, 7:00. Taillight lens comparison, 7:26. Shatter resistant Lexan material on the Chevy, 7:25. Coolant recovery tank, 7:45. Side terminal battery on the Chevy, 8:25. Banks of headlights are compared to show battery life in Chevy versus Ford, 8:38. Time lapse photography is used for 38 minutes, 9:15. Step side pickup for easy loading, 9:40. Chevrolet massive girder beam front suspension, double panel construction, higher GVW’s, bigger windshield, more hip room, aluminized muffler and tailpipe, coolant recovery tank, integral voltage regulator, side terminal battery with extra capacity, more models, dual rear-wheel pickup, excellent re-sale value. Man speaks to camera, 10:25. Chevrolet. Still building a better way. END PART 1. Written and produced by the Bill Sandy Company. Film opens with a jetliner landing on a runway, 11:27. 3 different Chevy models pull up at the airport, 11:40. Sport Van, Suburban, Blazer, 11:50. The hood of the Blazer is opened, 12:10. Blazer is on the highway, 12:30. Animation shows Blazer body construction, 12:50. Blazer carpeting and bucket seats, 13:15. Man loads a 4-door Suburban Super Wagon, 14:05. Man loads cargo into Suburban 14:30. Suburban 6 Cylinder engine, 14:50. Suburban 6 Cylinder engine, 15:00. 2-wheel suspension, 15:18. 4-wheel drive Suburban, 15:28. The Chevy Sport Van unloads passengers, 15:40. Chevy Sport Van interior features, 16:10. Chevy Sport Van exterior features, 16:30. Chevy Sport Van removal and re-installation of seats, 16:50. Wide choice of engines, for the Chevy Sport Van, 17:25. Chevy trucks tow campers, 18:13.
We encourage viewers to add comments and, especially, to provide additional information about our videos by adding a comment! See something interesting? Tell people what it is and what they can see by writing something for example: "01:00:12:00 -- President Roosevelt is seen meeting with Winston Churchill at the Quebec Conference."
This film is part of the Periscope Film LLC archive, one of the largest historic military, transportation, and aviation stock footage collections in the USA. Entirely film backed, this material is available for licensing in 24p HD, 2k and 4k. For more information visit www.PeriscopeFi...

[@jasonpark5906]

If I drove to a car lot today and they had any one of these trucks in brand new condition I would choose any one of these old trucks over today’s models.

[@jeffhiner9443]

I get behind the wheel of a 73-87 Chevy and it feels like I’m home. I drove those for years and years and will always have a fondness for them. But I wouldn’t pick them over my 2019 under any circumstances.

[@wonder-bred]

Ive been building a brand new 86 c10 for the last 10 years lol. I thought old trucks always had a lot of road noise until i put new window and door weatherstripping in.

[@chuckwhitson654]

Especially if you could take it home for 3000 or less. I'd do that Chevy with a 454, 4sp 4:10 gears and limited slip

[@youthmanrecords965]

Damn right you would. No questions asked sir. Sign me up

[@jasonpark5906]

@Matt H When you consider a new transmission for my 2019 Ford F150 10 speed is over $4000 to rebuild Who knows how much to replace? Ia transmission in my 74 Ford ranger only cost me 1200 it ends up being cheaper to drive an older vehicle that’s in good condition and well-maintained. I’m not aGear head but I know it’s cheaper to take my 74 Ford to a shop then it is my 2019 Ford. Plus I like the aesthetics of the older trucks. If you buy one of those trucks today it would be cheaper to keep it on the road in the new trucks out today.

[@matt59736]

I love these commercials that they make the opponent's vehicle look really bad like the guy was pounding on the roofer of the Ford and then he barely touched the roof on the Chevy. I grew up with these things in the 90s in northern Michigan. And I still drive them to this day that's all I run. They both rusted the Chevy little bit more than the Ford. I've had them alll Chevy Ford and Dodge. I praised them all and cussed them all. And I still won't own a truck newer than 86.

[@herpnderpn2484]

Chevy is still the smoothest riding truck I've ever owned. Never owned a Ford, but driven many. I currently own 3 dodges, the Chevy, and a Toyota. Chevy rides better than all of them. They all break though.

[@dyer2cycle]

..yes, when they gained computers(even basic ones) and plastic headlights, that is my cutoff date...I hated plastic headlights then, still do..It shocks me to see people pilling the nice glass sealed beams out of their 90's-2000's Jeep wranglers and XJ's, pickups and sticking those awful looking plastic replacements with the rows of little LED's in them :(

[@herpnderpn2484]

@@dyer2cycle Oh man, most of those plastic LEDs are absolute junk. And, you can but higher wattage lights or throw some KC Daylighters on top if you desire.

[@noneofyourbusiness3553]

The comparable model to the C10 would have been the F-150... They wouldn't want to compare apples to apples or anything like that now.

[@dyer2cycle]

@@noneofyourbusiness3553 ..no, the comparable model to the C-10 would have been the F-100..I don't think the F-150 came along until around 1976..The F-150 was mostly born as a way to raise the GVW just above the threshold of having to use a catalytic converter..a way of skirting the emissions requirements of automobiles...the Chevy "Big 10" was Chevrolet's version of this...not sure what year it debuted...maybe 1977?....

[@billyrayvalentine7972]

I bought a brand new 1976 F250 camper special with a 460. Man it was a great Truck. I always thought the Chevy looked better but that Ford hauled many a trailer's with no problems. Good times

[@theguy9234]

My dad has a 74 f350 super camper special with the 390.

[@those70sfords90]

I have a 78 Ford F-150 flatbed

[@bobbyheffley4955]

@@those70sfords90 straight 6 or V8?

[@those70sfords90]

@@bobbyheffley4955 351w V8 4x4

[@waynenoll1967]

That 390 was a badass engine! Had one in my 69 Torino

[@TrulyUnfortunate]

My dad bought that same Chevy when I was 9 years old. I learned to drive with it.

[@dnlcast2]

Do you want a cookie?

[@steelballs7456]

James Bond yes please

[@stubs1227]

Sorry to hear that.

[@edwardpate6128]

I had a 75 Chevy Beauville van back during the 80's. Drove that thing to hell and back. One of the most durable and reliable vehicles I've ever had.

[@BuzzLOLOL]

And worst MPG...

[@chevyguy6961]

@@BuzzLOLOL Gas was cheap back then and fuel mileage wasn't as important.

[@melrose9252]

@@chevyguy6961 < Yes mileage was important back then.

[@edwardpate6128]

@@melrose9252 Gas was cheap and I had money to buy it so I didn't worry about it.

[@patrickmcgoldrick8234]

They were a nice driving van.

[@PhaQ2]

I miss my Chevy step side. So reliable. It ran all the way to the junkyard, and then they used it as a yard car. Until scrap metal prices skyrocketed really high and the yard sold all it's inventory.

[@roger3858]

I wish America still had pride in its products and nationalism like it used to in these old videos... thanks for making me feel like I was born 40 years too late

[@megabyte7047]

Roger I don’t think the 70s are a good decade to highlight American’s pride in their work. American cars were crap back then and spawned the rise of Japanese cars.

[@kataccord1968]

@@megabyte7047 Well... that and the oil crisis. Muricans couldn't figure out how to make a good small engine

[@kylestewart8049]

As someone who grew up in the 70s and 80s I can say that living through those times no way would you say that was the good all days. Every one was poor and struggled to make a living. Looking back after 30-40 years all you remember are the good times and what now seems like a simple time in history. much like the time you’re living in now, you would say no way is it the good ol days. but in 30 years you’re gonna look back and say man! The birth the Internet and cellphones all that stuff was the good all days!

[@timfremstad3434]

@@kylestewart8049 What the hell do you mean everyone was poor????? No they weren't, my Dad was an enlisted man in the Navy(which aint exactly a high paying job), and we weren't poor, we weren't rich either, but we didn't lack for anything.... YOU may have been poor, but the whole country wasn't....the only thing I agree with you on is that later generations look at our time wistfully, like we looked on the 50s wistfully, like the next generation will look on the 80s and 90s wistfully

[@chrisstromberg6527]

OMG, this stuff was complete sh*t when it came out. I can remember my dad bringing home the new company vehicle and we were all dumbfounded when he could not shut the car horn off. He had to pull the wires from it to get it to stop honking. A fricking brand new vehicle from Chevrolet. Or all of the paint that peeled off of the previous 4 year old company vehicle from chevrolet. Please don't kid yourself, this stuff was poorly made and it did not always stay running.

[@The221wyo]

that ping-pong ball test was groundbreaking

[@hthouston3924]

Now days additional features cost more than this 70's trucks

[@yaboidustin2447]

Unfortunately you're right

[@u-shanks4915]

Which is ridiculous most of it is made in China But we have options Go to other states to find one

[@bechtoea]

I love how they say the Chevy is built to prevent rust. Let me tell you, a 1974 Chevy would rust off the frame within 3 years. I know as my family had one.

[@lelandfranklin3487]

Exactly! They just rusted right off the frame. Must have been the plexiglas on the side...

[@tomfairbourn6998]

This had me laughing my 73 was the biggest rust bucket I ever owned. really turned me off of GM products

[@bechtoea]

@@tomfairbourn6998 Chevrolet was the #1 truck up till the 73's came out. The rust issue was the single thing that put Ford at #1.

[@lawnmowermanlawnmowerman9930]

@Jeff Ring I had a 75 GMC Sierra that you had to hold your feet up if you hit a waterhole in the road to keep your feet from getting soaked.

[@bayareanewman1566]

So they rusted a lot. Sounds like everybody is in agreement. So what caused the rust? A Cost cutting measure they conveniently didn’t mention here? Anybody have any ideas? I’m curious as to everyone’s thoughts since a lot of the commentators here had one in their lives

[@BELCAN57]

When trucks were built like trucks, not cars like today.

[@heavymetalmadness666]

LOL I thought that way at one time. I had a 63 chevy 3/4 ton 4x4 283 4 speed trans.It could not do what my 97 4.6 ford F150 could do work wise and the ford wasn't torture to drive.That just isn't a ford vs Chevy situation.Go back just one year to 96 and I would want nothing to do with the 150, and I'm sure the 63 ford would be a joke as well when compared to modern trucks.

[@100texan2]

Robert Presti Jr but it’s all they had back then and they seemed to get a lot of work done with them. I guess when that’s all you know and all you got they seemed great. Of course those old vehicles weren’t as safe as today’s vehicles if you got in an accident. There’s pros and cons in everything but it seems a half ton pickup today will do what a 3/4 ton will do today just a lot of of plastic in today’s vehicles and more complicated. I tell you one thing, I don’t miss working on carburetors and distributor points.

[@danieldavis9832]

Back when you could just throw the camper in the bed. Now they give you beds you can barely fit a bicycle in

[@timbuk1126]

Dude trucks today are tough as hell. Go look at the crash test results yourself.

[@nathanmcdonald610]

@@100texan2 The flip side was that any joe blow could figure out a carburetor in a day or two. Today you pretty much have to be an engineer to do any serious work on a modern fuel injection system.

[@bloqk16]

I recall when my older brother got a Chevy 3/4 (three-quarter) ton Custom pickup in 1974. The nice aspect of going with the 3/4 ton rating was with the commercial vehicle classification it had when it came to engine smog equipment: It had none. He worked as a Chevy dealership mechanic at the time; and with the access he had to accessory pieces, he rebranded the Custom model to a Cheyenne version. That bit of deception bothered me. It was also a hint of the person he became in later decades.

[@dwcoop5390]

We bought a 74 Ford brand new factory order.. was a great truck

[@karlhiggins5765]

Those were the days, we would go to grandma's house on Sunday. After about 2hrs it never failed. One uncle drove a Chevy, one uncle drove a Ford. Always ended with them fighting over which truck was the best. Those were the good ole days. Lol

[@joshhoman]

At that point Granny should have said"Both you boys knock it off or I'll go outside, light both your stupid trucks on fire and we can see which one BURNS best!

[@Carla-tz7qw]

No one was bragging about dodge. They were low bid until they borrowed the Cummins.

[@trickyricky12147]

​@Carla-tz7qw Now that you mentioned it, yes. Nobody bragged about Dodge trucks until much later when they borrowed the Cummins. Lol. The only Dodge truck people might've bragged about was a half-ton D/W100 equipped with a 318 C.I. V8, but that was about it pre Cummins as far as bragging goes.

[@johnswanson3741]

Time tested years later.... Those Ford's were trucks, Chevy's were just pickups! Everything about comparing these two vehicles would tip Ford's way, Period! GM's were always lighter duty comparing similar years. Frames would twist, less leaf springs for the similar rating, 350 V8's were more problematic, front ends were lighter duty (hence the ping pong test proved that), they rusted out faster than a 2nd gen Dodge truck, weak transmissions, and lighter 4x4 straight front axles than Ford or Dodge. Guess one could say the people that decided on purchasing the Chevy's are a bit like the people that voted for Biden over TRUMP, just could not see the major differences between the two.......no common sense!

[@davidaustin9927]

This is when Gm took pride in building the best truck on earth

[@paulwatson4189]

And they were usually 300 pds lighter after a couple yrs from all the rust eating away the rockers and bed .

[@weskirkland5850]

My 78 C20 was built like crap. I love it and will never give it up but body fit was garbage and there were 5 different place on it you could see the primer through the paint. it was in excellent condition with 79k on it when i got it, always garaged. the chevy vs ford debate then was ford was way more primitive. if you've ever worked on both ford had stuff in the 70s chevy had in the early 60's. good reliable trucks both but gm was 7 years ahead all the time until the late 80's.

[@jeffreythomas4511]

I had a 1977 Chevrolet pick-up. I have kicked myself for years for getting rid of it. Loved it. Never left me stranded.

[@VIccs826]

Jeffrey THomas buy an ‘87 K10 then, I’m sure you could find a cheap one and fix it up

[@wizardmix]

I'm here for the canned 70's music, the wow/flutter and the gritty cigarette saturated voice.

[@timbuk1126]

Wow/flutter?

[@wizardmix]

@@timbuk1126 recording terms referring to the way old tape and/or a poorly calibrated tape machine sounds. WOW -- is the fast and slow pitch shifting you hear making it sound "drunk" FLUTTER -- is the jumpy buffeting you hear where it sounds like a person is speaking underwater. While these were once problems that needed to be avoided in the recording industry, in the last 25 to 30 years, wow/flutter has increasing been used as a desirable affect in recordings. There are countless tape simulation plug-ins on recording software and effects pedals that incorporate Wow/Flutter.

[@youthmanrecords965]

@@wizardmix Yeah there’s plenty of VST plug-ins that emulate grainy saturated tape real to reel sound with wow & flutter variations !

[@wizardmix]

@@youthmanrecords965 I use a few of them🤙

[@jamesrecknor6752]

Johnny Carson had the best cigarette voice

[@lancelotlink3907]

My dad had a 76 GMC Van with the 400 4 barrel. I took it to high school once and removed the engine cover and took my friends for a drive so we all could watch the 4 barrels opening up. Good times.

[@DeanMk1]

The ol' Rochester "WHOOOO", when the secondary's kick open. Here's a reminder of good times gone by... kzbin.info/www/bejne/enSwhqVpmJuLbZI

[@lancelotlink3907]

@@DeanMk1 Yes the Quadrajet. I got really good at rebuilding those things. Thanks for the cool video.

[@Boxpok]

A good friend of mine had a 74 W200 4x4 Dodge Power Wagon, that's when trucks weren't play toys like today.

[@JASONHJEFFERSON]

thats when trucks were trucks and men were men

[@Nate......]

I got a 97 Silverado Z71. I don't think that truck can die. I drive the hell out of it. do everything under the sun. still a beast!

[@wilsterone6689]

I've got a 93 k1500. 375k all original except brakes and battery. Runs and drives like the day I bought it in 1994.

[@Mr_Chris77]

I came here to read the pissing match in the comments section.

[@DeanMk1]

Ha! right on. My dad had a '74 Chevy half ton. Long and wide, it had a 250 with 3 on the tree. It was a "Custom" and such a plain jane, the local dealership had to call around other dealers to see if anyone had one. 3 days later he found one. We had that truck for 20 years. I remember many hunting trips in that truck. Never failed us. =)

[@ffarmchicken]

DeanMk1 I just picked up a 70 GMC bare bones with the 250, three on the tree. An old school district truck at a junk yard. This thing is super simple, after sitting for three years with old gas, put in a charged battery, poured a dash of clean fresh gas down the carb, fired right up! Amazing. Try that with any new truck under the same circumstances.

[@KevinRichards-rk3gp]

Back in the day when power steering & power brakes were optional. Nowadays everything has them.

[@DeanMk1]

@@ffarmchicken That's one of the great things about older vehicles. No dam Government instituted CAFE ratings to push the auto makers into making shit more and more complicated. It only takes air, fuel and spark to make an engine run. Everything else is bullshit.

[@DeanMk1]

@@KevinRichards-rk3gp Yes sir. My dad's truck did have power front disc brakes, but you rowed your own gears and steering was by armstrong. Even though I'm older now, I still miss that.

[@KevinRichards-rk3gp]

@@DeanMk1 what was cool about those generation Chevys, GMCs, & Fords back in those days when they were new was they didn't have recalls like the vehicles nowadays.

[@mistered9435]

I really liked yesterday’s CHEVROLET, but modern-day, real people are getting the heartbreak of America, and it runs deep, because GM’s quality has dropped like a rock

[@herpnderpn2484]

To be fair, it's really hard to screw up quality control of a painted metal dash. It was true then, and now. They are building what the consumer wants..... A new vehicle every 5 years and as many bells and whistles as possible. And no metal dashes

[@mikemoscato2995]

Yeah the new chevys electronics when they go wrong the motto like a rock,IT JUST SITS THERE😎

[@galesams4205]

will still go with the ford.

[@mistered9435]

@Hunter is a rat I love the 73-80 square bodies. In the 90’s, my brother restored (2) 1976 Silverado 4x4’s. Both black with red interior, both with 400 sbc. They were restored to pure stock and I drove one of them for several months. Loved that truck.

[@brandonbell3089]

@@galesams4205 I will never want to walk 😂😂

[@paulne1514]

Coming from a ford family, I had to buy a Chevy truck. It is the best (back then and probably even today) for carrying a slide in camper. The deluxe camper pkg, came from the factory with frame mounted tie downs, shocks in the front of the bed, connected to the cab and front stabilizers. Plus the lowest center of gravity, even with 4x4. At 8,400 lbs, it rides almost as smooth as my 91 Lincoln Mark 7.

[@user-vz2ei3sb7r]

Love these old Commercials remind me of my childhood. My opinion vehicles where made a lot tougher. Back then 💪

[@timbuk1126]

They were actually really unsafe compared to now. Go look up the classic 50s Bel Air/Malibu crash test.

[@tonywilson2530]

My first pickup was a 1976 Chevrolet Scottsdale in the very same color scheme red/white two tone. Loved that pickup. Wish I never sold it

[@KevinRichards-rk3gp]

You'll find another one out there. I still see some of those generation Chevrolet & GMC fullsize pickups on the roads today, just not as many as I use to back in those days. Those generation Fords on the other hand are super rare nowadays, & the easiest way to find one of them is online.

[@jeffreylines1535]

I remember Dad's half a 1975 blazer, I say half because that thing had so much rust the door skins flapped on the highway. The engine was rock solid but the body was worse than swiss cheese. Seems like the 73-76 GM pickups in our area were horribly rusty. Dad's blazer was so gone by 1986 that we pulled the engine and let the rest dissolve on the farm. The truck that offered value was the 72, so glad we kept that one!

[@231mac]

No idea where you people that keep claiming this live, but there are 70's models all over the place in the south.

[@ericl2969]

@@231mac We live in the north! There was a span of a few years in the mid-1970s when Chevy trucks would start rusting the very same year that you bought them, and a few years later, there would be rust everywhere and the lower 1/3 of the doors would be gone. The other brands rusted really badly too in those days, but for that particular span of time, Chevy/GMC was quite a bit worse.

[@RoadRunnergarage8570]

Thanks for keeping the videos coming through tough times..

[@danc506]

These kind of comparisons need to come back

[@weskirkland5850]

There would be lawsuits all back and forth so bad they'd lose money nowadays.

[@richardcraniumdicksinn3959]

Since 1974' 80% of Chevy trucks are still on the road. The other 20% made it home. Lol. Both trucks are very nice, I've owned a few of each & liked both brands.

[@WMAT77LL]

😄😂

[@FIREPHILSPENCER]

What's crazy is I still see those old square body Chevys still on the roads while those old Fords are long gone.

[@dennislangston487]

The square bodies you see are mostly late 80's. Late 80's Fords are 2 series away from mid 70's. I see plenty of early to mid 70's Fords . Not so much Chevies . Maybe it is what you look for.

[@FIREPHILSPENCER]

dennis langston Doesn't matter the decade I just don't see older Fords compared to older GMs, in fact it's not uncommon to see an old GM scrap truck with a Ford tailgate on it.

[@mebe2k]

Come to the PNW...lots of old 70s fords still running around...70s Chevy/GMC are few and far between.

[@bk14nyc]

I had a BEAUTIFUL 1977 Ford F-250 Trailer Special with the 460 V8 with Factory Ice Cold A/C. I use to Trailer my 1970 Ford Galaxie XL 429 N Code Thunder Jet. Lost it in Hurricane Sandy in 2012. I couldn’t sleep for Months after that! 😞

[@angelo_giachetti]

My dad bought a new 74 C10 6 cyl. It had 1 option, an automatic trans. Was a good solid truck.

[@TexasHarleyBoy65]

After Ford mastered the all important 'Ping Pong Ball Test', they never looked back. I know in 40 years of driving pickups, how important it is to show up, with your balls still in your goblet......

[@dennislangston487]

I wonder how much air they let out of the Chevy tires before that test.

[@jasonpark5906]

I read “ping pong ball test” in the narrators voice in my head.

[@boomermarr]

I've owned both brands and loved both for different reasons. Watching this made me think that if GM only knew how bad their trucks would rot away,they wouldn't be tauting about how great the truck is built to prevent rust.

[@dennislangston487]

That is an old, old advertising trick. Pick your weakest point and promote it as a strength so potential buyers will just look right past it.

[@ffarmchicken]

I agree. I have both trucks and both have rust equally bad, I’m in the salty Midwest.

[@datrevmeister]

How do they rot? I purchased an 87 GMC Sierra about 8 years ago that had never had any work on it done, and there was no rust on it.

[@boomermarr]

@@datrevmeister first, let me say that I was speaking in general terms. There are always outliers to a circumstance. Secondly, it also depends on where you live and how the vehicle is maintained and whether it stayed outside or was kept and stored indoor. I live in the south eastern part of the country and we have very humid weather and a lot of road salt used in the winter. Chevrolet,especially trucks used for farm work rusts terribly. 70's and 80's Chevrolet trucks rust especially bad. All that said, if you have a good, solid, rust free Chevrolet truck then kudos to you. You have a truck that has been pampered for most of its life. Enjoy your vintage Chevy and be very glad it wasn't used and abused all its life.

[@merc-ni7hy]

ppl who bought the chevy soon learned that the frame would crack around the steering box...and the hood would bend after while cuzz the hinges would get stiff ..and they didnt tell you that ford used alot of galvanized steel where chevy didnt..and anyone who lives in a snow state would soon realize the chevy was a real rot box ,,and the fords rocker panels would last alot longer then the chevy's

[@presleysiler6454]

Sounds like your a ford guy

[@merc-ni7hy]

@@presleysiler6454 a proud ford man

[@presleysiler6454]

😂

[@johncholmes643]

@@presleysiler6454 Anyone named Presley isn't old enough to remember these things in the 90s.

[@johncholmes643]

@@merc-ni7hy You couldn't be more correct

[@countdown2xstacy]

“Those days are gone forever, over a long time ago…oh yeah”

[@super20dan]

the 73-79 ford is the best truck of all time

[@vaquero87wrangler]

6th generation😍 I have 78 like 20 years

[@jasonconklin8172]

Rust bucket both Chevy n Ford upper bed behind cab upper ft fender never a fan of this era truck 67 72 now those were trucks

[@rojeliofraga9150]

I have a 1979 F100 Custom short bed, all original

[@guddergo7116]

@@jasonconklin8172 the chevys from the coast were so much more rusted from the bottom. Here in Texas we always ask " your chevy truck been to the coast? " if ever considering buying a older chevy truck. I used to have a 1970 f100 .

[@Blazefork]

Had a 77 F250 4x4..... wish I had it back

[@jessefarley4609]

I love these trucks as much as rust does lol

[@kennethsunderland6676]

I have a 74 and hope to get it back on the road in September! Mine is the same color combo and is a Cheyenne Super too! Been in my family since 89! Thanks for sharing this video!

[@roncoburn7771]

I love these old Chevy commercials

[@JoeL-re1dc]

Being someone that owned a half dozen square bodies, starting with a "73....... your special, tough, super duper, triple part fenders, weren't so great..............lol

[@ffarmchicken]

Joe L First thing I thought. They sure are hard to find without rust in the Midwest. Lots of nooks and crannies for moisture to sit and eat away around spotwelds.

[@jeremybennett5547]

Learn as you go I guess. Sure it seemed like a good idea at the time

[@geirmyklebust]

My daily drive last 3.5 years is my 74 El Camino, old Arizona car. Just love this car, way more than my previous MB-220-CDI. Its .... kind of costly, BTW.

[@02autogt]

After the rest of that Chevrolet rusted away the tailpipe was still laying there...

[@bechtoea]

That's BS. The tailpipe rusted away too. :)

[@iwanaGoFast2010]

I never trust companies that have to explain how good they are.

[@nathanmcdonald610]

That's been GM's schtick for decades now. I find it hilarious how they'll dog on Ford for something new and then in model year or two they'll implement the same thing on their own trucks. The most recent example of which was when Ford went to aluminum body panels over steel.

[@gearyheidinewaccount3237]

Better not buy Ford or Dodge then

[@idontcare3013]

I'm definitely sold. I'll always pay the extra dollar for a Ford. I don't like spending time in the waiting room at the shop.

[@lawnmowermanlawnmowerman9930]

LOL,you are so right Sir

[@ericl2969]

They're all good at times, and they all break at times. An earthmoving contractor I know just switched their whole fleet from Ford to Chevy because the Fords were in the shop too much to suit them. But this can go either way, depending on the year, model, specific engines, transmissions, etc. Anyone claiming substantially better or worse quality based strictly on brand is speaking from emotional loyalties alone. On the other hand, certain brand-specific features could be better or worse than average. Ford's twin I-beam suspension was a bad idea from the beginning, with the tires swinging in semi-circles as the suspension moved up and down, leading to lateral movement (scuffing) of the tread and poor tire life. Chevy's independent front suspension in those days allowed a much more efficient compression and rebound (much less tire scuff) and it was remarkably rugged too. But I bet you could find other specific comparisons favoring Ford or other brands. I was always a fan of International, but they had their flaws too (especially rust).

[@93sundance]

I'll take a K-10 and a K-5 PLEASE.

[@TysonNeil]

I've had both at different times. Still have the K5 although it needs a bit of work. A barn resident for a long time.

[@rossgreenzweig]

The chevy vehicles are beautiful!! The Sportvan would be my pick, jist love the looks and interior 👌

[@ltunedkc]

Well I am a Ford guy and this video shows how you can rig anything to make your product look good. But if I came across a clean C10 I would love to have it.

[@Trance88]

Gotta love that funky mid-70's background music on the second part (1976 model year vehicles). I love the fabric pattern on the van seats. Everything today has to be grey or black fabric, pleather, or leather.

[@alexeatonexploresamerica5511]

I wish there were more old chevys around

[@paulwatson4189]

most rusted to a quick death.

[@ProjectFairmont]

The GM had better engines and steering, however it did not measure up to the Ford in terms of ride, suspension travel, body integrity and rust resistance. I think the 70s Fords have an enduring quality, not surprising as they were designed in 1967.

[@Lvatopesado]

@Warren - Same here.

[@chrismontreuil2206]

@Randy Wiesendanger except the rust department.

[@theguy9234]

Id have to disagree with the Chevy having the better engines. They had one good sbc v8. The 400 sbc wasn't a good work engine, unless the overheating issues were fixed. The 454 was ok but only option. Ford had over 4 fe big blocks to pick from for the truck.

[@christianmotley262]

Ford didn't have better ride

[@lancelotlink3907]

@@theguy9234 Dad had a 1976 400 4 barrel GMC Van and we never had overheating problems but it came with an over-sized radiator because it had dual AC front and back. Mom had the 1972 Ford 400 2 barrel in her LTD and that was just as reliable. We lived in desert to with 110 temps. That said Dad and I kept up the maintenance most of it done in the driveway.

[@dolnick7]

Vehicles had classic designs back then. Like a Stratocaster, they couldn't be improved. Most of today's vehicles -- if you can even tell them apart -- look like crap.

[@heavymetalmadness666]

If I post three pics of a 1930 Ford, Chevy, or Dodge my guess is you would label them wrong All cars look the same by decade for the most part. Now the part of that that one could argue is well over time more models were being made rather than one main car with different trim levels.

[@kevinrichards3288]

The brand new body style on the Chevy Silverados looks cool tho.

[@mr.nobody68]

Stratocasters suck though. Horrible comparison. You need a McCarty 594 to compare

[@garybell523]

Most cars today look like a dog taking a shit.

[@gearbanger57]

Chevy was just getting back in the truck game after building those lame coil spring trucks, my dad always bought GMC's. I've owned em all, even Dodges, through the years and they all have their downfalls. Bought a new truck last year and after driving them all i got a GMC, I'm happy with it.

[@ericl2969]

You mean the coil springs in the rear? Yeah, that was a bad design. The link arms would wear out and you could stand at the back end and slide the body back and forth over the axle! They had a really "boingy" ride in the back end too!

[@alexeatonexploresamerica5511]

This video mean a lot to me. I love Chevy

[@mikedrown2721]

GMC for me

[@freerepublicusa2064]

The best Chevy/gmc trucks and be everywhere owned was the 2003-2007 2500hd. Mine is 06 Duramax LBZ. This truck is by far better than the new ones. I’ve beat the heck out of it and it runs and runs. Great brakes, ice cold a/c. Tough torsion suspension.

[@bengomes8845]

These days the Chevy because parts are plentiful, but rather have the ford with a 300 inline 6

[@ffarmchicken]

I’ve got two of those fords. But also have two of the Chevy 250 inline sixes with three on the tree. All four run the same to me.

[@mr.nobody68]

Somebody wasn't paying attention

[@gearyheidinewaccount3237]

I'll take the 292

[@gregorybeers5831]

I just traded my 2019 Mitsubishi Outlander in and in its place purchased a 1999 Chevy suburban with a 350 4 Speed automatic and I’m very happy I’m finally driving a vehicle that I wanted to have looking back I was always looking for a vehicle like the older Chevy trucks and I feel in love with them ever since my dad bought his 1973 Chevy Cheyenne super 10 and it was the first vehicle I would tune up an engine on and years later perform body work on.Chevy Rules the other drools!!!

[@Bigdog302V8]

Both were very Good Trucks, the 1973-87 Chevy and GMC trucks were prone to rusting out bust if you want to restore them, you can get the parts to do so, Same with the Fords and both makes have a Plethora of Engines to work with. when it comes to the six cylinders I lean towards the Ford 240 and 300 CID and the Chevy 292 and pretty much all 8 cylinder engines are great choices.

[@timhede9560]

I have a 73 c20 Chevy. Runs great. Tough truck. Chevy is tough...

[@alanmeyers3957]

Those square bodies are chit boxes, the ford is a better truck.

[@marine4lyfe85]

That K5 Blazer 4-wheel drive is so sweet. I always loved the removable cap on the rear.

[@seanonwalkercreek.7356]

The Narrator Sounds like the Legendary "Winnebago Man"!😁👍

[@toddbob55]

Ford Trucks do have better Frames... My k10 Chevy is notorious for Cracks in the frame in many areas " watch Stacey Davids stunt Double " on youtube. Also the 9 inch rear Axle is also much stronger on the Fords . Fords were Tougher trucks but if you take care of any truck it should stick around awhile.

[@TysonNeil]

My K10 had cracks at both rear shock mounts.

[@spartan005u8]

As I'm mainly a ford guy but these old competitive commercials are great I do respect dodge and chevy love them all tbh

[@dennisgriffey8448]

All the perfume in the world and its still just a chevy!

[@samduran5180]

Right you gotta love the small block taking over the world, if only they could see where the small block has gone. And Fords v6s and aluminum 😂🤷🤦

[@marksimpson2451]

Bought a 75 Silverado in 77. The box was rusted out by 80 and the doors and can corners by 82.loved it so much I bought a 74 GMC Sierra to replace it.lol

[@gearyheidinewaccount3237]

Must be where they salt the roads

[@BuzzLOLOL]

I want the '57 GMC pickup with stock Pontiac 347" V8 and 4 speed Hydramatic transmission and positraction... Ford pickup shown is the 'dentside'... full length dent down the side... sometimes filled with optional trim...

[@dennislangston487]

I think my cousin owned that 57 for a while. The Pontiac engine was sitting on 2x4 blocks with short log chains holding it down...lol

[@timokuusela5794]

I have a -79 Blazer, owned it for 35 years now. And, it has an Optima battery that is now about 30 years old. They do not make trucks and batteries like that any more. If Chevy started to make the K-5 Blazer again, I think I am not the only one to buy it. Just add a modern V 8 and not much more is needed. I also have a Hummer H3, and the feeling I have when driving it is that it may break at any moment; everything is too electronic and fancy...

[@davidgarris2513]

To be fair , for years if you combine the Chevy AND GMC sales , it's about the same as Ford. The actual difference is less than we are led to believe.

[@squangan]

My family owned both when they came out. My father had a ‘77 F250 4x4 crewcab Custom with a 351W 4 speed in it, and my older brother had a ‘77 GMC Sierra 3/4 ton 2wd with a 454 and four speed in it. They were both good trucks but I remember my father calling that 351W a gutless wonder, it had little power and sometimes pulling steep hills he’d have to drop it right down into 2nd gear.

[@ilovecops5499]

3+5+1 = 9. 999 - 666! Chevrolet 350. 3+5+0 = 8. 454 = 4+5+4 = 13, Friday the 13th. They are occult.

[@mrglock2313]

My 1975 Ford f100 still on the road zero rust. Pull up to a 7 year old Chevy rust bucket at a red light. Turn head and grin, light turns green, I grin again with my 460 big block. 😆

[@ryanfrederick4889]

And they smoke you off the line with a 6cyl that 3x your gas mileage! Then they grin. I'm just kidding around! I have a 72 with a big block i get it.

[@anthonycassata5152]

Now that comment about the camber, I don’t care what you have, camber is going to change, now because of the difference in the suspension, the Ford will have more positive camber. But, as a Ford front end mechanic many years ago, the Ford has a much simpler, easier front end to work on. 🤷🏻‍♂️🥸

[@davidaustin9927]

That's when chevy engineers built the best truck an the company wasn't so cheap they really cared about what they built

[@melrose9252]

These Chevy’s would rust on the lot.

[@nathanmcdonald610]

They cut a lot corners back then just like today.

[@madgav935]

I love how they tell us right away who they think is better

[@robertroberts9782]

I had a 77 4wheel drive 3/4 Ton 350 c.i. with a plow...best truck I ever owned made it to 330k b4 it was Stolen !!! In 2004

[@Lvatopesado]

Good comparison, 3/4 ton chevy vs 1/2 ton ford.

[@ericl2969]

Um, no. Both were half-ton trucks, no question about it. I was around in those days and can spot the difference between 1/2-ton and 3/4-ton trucks of any brand from those days in an instant.

[@j.t.illingworth7925]

I’m a Chevy guy but isn’t longer battery life and coolant overflow tanks stretching it a little bit?

[@rossgreenzweig]

Not back then, that was actually a deciding factor for some..

[@MyBenjamin66]

Chevy K5 or K10. I still love the 73-87 chevy trucks

[@mikegroat7732]

At 4:50, that is why those square body Chevys rusted so bad. Salt and crud got stuck between the inner and outter fenders.

[@bloqk16]

Not only that, but the paint on the '74 Chevy truck my brother had went bad in 20 years; and that was in the mild California climate. The roof of the cab turned to rust.

[@robertcarter4448]

How about the rust issue chevy trucks had from 1973 to 1980

[@johnz8210]

Yes, they were really bad with that. I'm glad there's people around that remember the real story with these trucks. Mechanically they were pretty good. Body - terrible.

[@robertcarter4448]

@@johnz8210 my dad had a 1977 Chevy blazer it rust pretty bad was that old at the time he also had a 1973 Ford f100 the body didn't rust nearly as bad as the blazer i remember see Chevy trucks from this area with really bad rust issue growing up lots of them i remember have wooden beds were i grew up at in Wva

[@johnz8210]

@@robertcarter4448 I almost forgot about the wooden beds people used to put on them. I think the Fords did have at least some galvanized sheet metal and didn't rust as bad, but I do remember Ford cab mounts rotting away - but it took many years. One story I have - going down an interstate highway in a '74 Chevy pick-up, and a big flashlight that was laying on the cab floor - the kind that held 3 or 4 "D" cell batteries - fell out a hole in the floor of the truck onto the road. It ran good, though.

[@randykirchhevel7311]

Use those Chevy trucks for working and driving down lots of bumpy roads I bet eventually after so much ware and tare you will see ping pong balls starting to bounce.

[@HioSSilver1999]

Ford had rust issues to in those years. As to where the outer body rusted on the chevy stuff the cab supports and floor pans rusted out of the ford.

[@Hot80s]

my first truck was a 77 sierra 2x4 i loved it

[@lawnmowermanlawnmowerman9930]

This is hilarious,Chevy's of that era rusted away while you were driving them. Ford's zinc coatings made them last 5 times longer. I've owned both of these trucks,the Ford was a way better value.

[@ejohnson3837]

i think he was drunk

[@brandonbell3089]

Uhh no the fords Rust just as often buddy 😂😂. Especially the ford wheel wells there always gone 😂😂

[@stevedeleon8775]

My first Brand New vehicle I bought was a 1981 GMC High Sierra 1/2 ton fleetside short bed two tone paint Metallic Root Beer Brown & Artic White Quarter Panels & Cab

[@djsonfire0001]

Chevy was dope back in the day!

[@lawnmowermanlawnmowerman9930]

More like junk,from all the ones I worked on for all my family and friends.

[@djsonfire0001]

@@lawnmowermanlawnmowerman9930 well I definitely believe if somebody does the upkeep on a vehicle no matter what brand it is it lasts there are so many people that don't and they just go to crap then they have problems everywhere. My 70 2wd short box was phenomenal bone stock!

[@djsonfire0001]

@@lawnmowermanlawnmowerman9930 what's your fav truck and year?

[@lawnmowermanlawnmowerman9930]

@@djsonfire0001 I've owned several different F series trucks of different models,but I've always had a thing for the 1959 or 1960 model F100, my daddy traded for one at one time and let me play with it and drive it around our community. I always liked those trucks.

[@deadlion9197]

This is funny to say the least "Here we have steel and cast iron, we think the steel is stronger but you be the judge". In 1974 they were all great.

[@dsma2023]

46 years later, nothing has changed.

[@nightbot706]

Alot has changed. Trucks are garbage now and selling points are how many crotch goblins you can fit in the back seat and how many USB ports it's got

[@tacomas9602]

@@nightbot706 Can't get a manual trans

[@SealofPerfection]

@@nightbot706 True, but the trucks today will go far more miles, are faster, more comfortable, and tow/haul far more than old trucks ever could. A half ton now can haul more than a 3/4 ton did in the 70's.

[@noahgaray7923]

Nightbot even this test was complete garbage. Look my balls move less than yours, my roof makes this noise when I poke it, etc. what kind of bullshit is that? They should’ve pointed out how Chevy offsets their rear shocks to counter axle wrap. GM commercials have always been trash, and always will be. Only GM I have Is a 72 cutlass supreme. Oldsmobile, miles above Chevy.

[@Hot80s]

bullplop!

[@Erik-rp1hi]

I had a 74' Ford E-100 Econoline van. I was a great van. Had it with over 200K miles and bought a 97 Econoline. Put 200K on that then in 2017 was going to buy the Trasit but got a Mercedes Sprinter for $3K less than Ford wanted. Didn't want to jump ship but did.

[@alfresco4976]

That is one long-ass E-100!

[@amilcarnanez8476]

Ford the Best truck, My father had F100 1974 V8 when I was chlid

[@presleysiler6454]

The video sounds like chevy rocks. But that must just be me.

[@shawnhuff3920]

My dad bought a 1974 gmc the day I was born in April 2nd 1974 right after I was born so he could take his first son home in a new pickup truck

[@jamesrecknor6752]

That is really neat

[@bbodinefan11]

Those Fords are still on the road. The chevys rusted out.

[@SealofPerfection]

Way more GM trucks from that era still registered and on the road today

[@mt1885]

Furrds are absolute GARBAGE with the 'Turbo v6 JUNK cam-chain stretch along with limp mode and failed transmissions'.

[@mudduck754]

Sitting here in my '75 C-20 that's been in the family since Dad ordered her in September of '74 and been a daily driver ever since. I drove her to high school. looking at the odometer that just hit 70,000.0 for the seventh time that's 490,000.0 miles. thinking your misinformed.

[@SealofPerfection]

@Warren He's misinformed because he's wrong. More GM trucks from that era were sold, and more remain on the road. Facts.

[@bbodinefan11]

@@SealofPerfection Ford took the sales lead in 76 i believe. You literally need a tetanus shot to stand next to any truck chevy built in the 70s. Maybe there are more where your from. But where i live seeing a 70s model ford is a daily thing. Rarely see a chevy from that time period. Lots of 80s model chevys though.

[@301Pont]

Both. I like GM and Ford.

[@johncholmes643]

It's good to know that when I want to haul a real load of ping pong balls.........

[@JohnnyRebKy]

I think both Ford and Chevrolet made fantastic trucks back then. Couldn’t go wrong with either one. I had a 69 Chevy and a 71 Ford. The Chevy was better looking and the Ford was more robust.

[@douglassopa2544]

both trucks did there job very well. still the better trucks today. you cant sell this me this noise. cause dat 75 ford pu in da garage still runs perfect. problem free. key here is maintanance,,,,,

[@jfchonors8873]

Interesting how the only competition GM worried about in 1976 was Ford. Little did they realize Toyota would soon assume a major role in the market

[@ypop417]

Love those 70's clothes so much polyester LOL

[@broughswenson651]

Ah the old "ping pong ball challenge!"

[@brendas.1374]

I miss my 1976 Chevy C-10 Custom Deluxe truck. It was a short bed with a 350 V8. I paid $1,900 for it in 1983. It had no rust and it was a California truck.

[@ajw9172]

Now just think today that truck is worth more than $ 19,000.

[@chrispaulson2934]

Had an 84 Silverado 4x4 when I lived in NC. Beautiful truck. But the worst I ever owned..always failing me. I traded it for a 74 C-10 Custom Deluxe. Same as yours being a short bed and 350 V8. It was 3 shades of black and rusted through. It never let me down. I was hoping to make it a tribute truck of the one in "The Driver" . Sold it for $1,200 4 years ago. Almost overnight these trucks became the next big thing and still are.

[@darthvader4hire]

i own a 74 C-10 Cheyenne Super its the pale blue (like hawiaan blue) and white color combo. factory 454, A/C dual tanks PS PB black interior and get this, a wood bed floor. i bought it for myself as mt 18th birthday present many a year ago and really loved driving it. it has the typical issues such as the famous body rot and the bed floor is getting really weak looking. and the old BBC...well lets say when it starts knocking LOUDER than normal (been that way for decades) you have to stop and add oil and whilst stopped check the fuel level LOL!!!

[@stonetempledave8584]

13:28 Loose bumper trim🙄. I do love the Chevys though 13:20 missing bumper trim!

[@honeybadger0559]

The bumper trim was optional, just like the bumper guards, both on the Chevy and the Ford.