1982-1992 S10/S15/Blazer/Jimmy Window Guides 🔧

[@dishinitoutdoors6811]

This was the best commentary in a how to video I’ve ever seen!

[@11Z50Ret]

Thanks for helping me and my son out with his first truck! I owe you two beers!

[@GHOST5400]

Thanks for making a super long video without actually putting the window in the door

[@endersphel7398]

I've definitely seen longer bs videos than this. He did exactly what he said in the title; Installing window guides. But if you need help putting the window back in, it's fairly simple! Slide it in somewhat tilted so the front bit (The side with the curve to fit the door) is more curved downward in order to slide it in. Once in the channel, simply rotate into position and the clips will clip in. They're designed to go one way - In, not out. If you need further help, I'd be more than happy to draw a diagram to further explain what I mean. Hopfully this helps if you haven't installed it already!

[@Anarchy-Is-Liberty]

Thanks dude, this is awesome!! You never know what you're buying, so this helps a bunch! Appreciate it!

[@Ghostacc956]

Thanks, this video helped clear up my confusion on how to use this dorman clip from autozone. Somehow mine fell off and I’ve had to keep my window rolled up or else it would come off the track. Quick tip for anyone, I did have to sand down the edges to make it fit for my car.

[@jamesmaddox40]

The pain of that installation was enough for me to subscribe and give you a thumbs up. I had done it in the Blazer door not knowing that there are 2 guide clips opposite each other. I did take the glass out the driver's side, but if there was a hole, I was oblivious. I really need to replace the channel. I will check and see if you did that video and gave the source, also I will check the comments below mine to see if it is there. I didn't see the info in the show more section.

[@dchachacha5663]

Hell yeah Shawn thank u man. I’m about to do this on my 87 and I didn’t realize wtf was going wrong. Got 2 clips and gonna pull the glass and try to get it all straightened out.

[@000MACK000]

Thanks for the info I ordered me five of them from the recommended seller the price has went up since this video costed me $40 for 5 give or take.

[@guitarb]

I just did this job on my 91 s10. I ordered the suggested clips and it worked fine. I was able to do it by hand with the window already in the door. Tip. The side with the peg goes on the inside of the window. Push that side through the window hole first. I was able to then snap the other side in with my fingers. Hope this helps.

[@martyn2012]

Thanks for the info,gonna pass it on to a friend.. make more videos man you had me pissing in my pants 2 minutes and 40 and I'm dying

[@CentricWorld]

Mouthpiece method Microwave hot water for 6 minutes place them in there for 2-3 then pull on under knob w plyers and you can just snap them on with fingers

[@endersphel7398]

Thank you for this guide with the window guides, haha. Both my windows guides broke/rotted away and need replaced but I had no idea how the new ones went on (No instructions with the parts, unfortunately) and the clamp idea is great! Unfortunately, there will be no "pleasure" for me since I'm too weak to clip them by hand

[@speedineed5327]

Thanks for the seller info. Kinda wish you had included reassemble. That's ok though . Kinda hope I can do it by hand. At my age a good BJ has been few ,and far between. LOL . Take care!

[@davidpardo8647]

Very nice tips... I have a question after you put those little things on the glass how did you install the window back on the door?. I mean because the reels ? From the frame window.. gracias

[@larryhojer469]

Just did this on my 90 S15. The clamp is the only way to go to get it done right and not screw up the clip. However, the real secret is to heat them up with a heat gun or hot water until they become pliable and then put them in place and clamp them.

[@Core297]

I feel letting them sit in hot water for a while would be safest, because it can be easy to overdo it with a heat gun, or at least some models of heat gun, and melt the plastic

[@barrydent-uy1um]

Do you have a video on how to take out a power window off a 92 S10 ex???

[@paulk5311]

i have bought quite a few of these over the years and find some are easy to install and some just do not want to work. the peg and hole that snaps together is usually the problem in my experience. some i have had would not fasten no matter how much i tried. it was like they were just too narrow for the glass. i also found a set of channel lock type pliers works well in place of the c clamp you used. if it snaps together right away then good but if it does not seem to want to snap together then you may have gotten a bad one. i have had a couple that just would not snap together and one i wound up gluing to the glass with goop. it lasted several months but then gave way. the new one i replaced it with went right together no problem. go figure.

[@Lou8430]

This is what I needed but trying to find the seller is not easy do you have a link to him there are 157 seller's I tried to put the comply name in and it did not work

[@ceridwenluna]

Your choice words accurately convey the pain the ass that this is. lol

[@mcgyveraddismetrotechnolog9358]

Hi dear brother...I've the same problem with my s10 1994 blazer...and I'm wondering if this plastic part can be printed out with 3d printer...any idea 💡 🤔???

[@dentman62]

I replaced my guides and the wondow still dont go up and down in the track right

[@HardCoreGarage]

I use channel locks

[@geramane5184]

Link?

[@DavidJohnson-ix7ij]

I just replaced one on a 92 S10 bought from Amazon a doorman brand I put a little gun grease on the tab it popped right in but I'm for sure going to pass on your offer

[@bryanroberson4804]

yea AutoZone's does not work at al. did the eBay thing now to wait for them. Rebuilding 92 Sonoma SWB grown up. Thanks.

[@chadjay828]

Damn that’s nice to know I just purchased some from Auto Zone a couple of months ago so I guess I’m not even going to waste my Time trying to use those ones just gonna order them from eBay

[@chadjay828]

@@shaun4bigblocksllc do you by chance have the sellers information from eBay so I can get those window guys/clips I bought them from AutoZone and obviously they’re not going to work

[@paulk5311]

i've had a few. some worked some didn't. maybe the ones that did not came from the zone as i have purchased from there as well as o'reillys and advance.

[@Yousitech]

I snapped mine in with my fingers today. The trick is to put a drop of wd40 on it

[@yungtooli]

well he better pucker up his lips!

[@janekoismaa]

Got new ones and cliped them with two fingers...

[@davejohnson4472]

Put them in hot water for 30 mins

[@HHS6272]

Do these work good, even tho they say made in "taiwan" ? 🤔

[@jonathon6976]

Challenge excepted

[@tommybuschur9859]

Fucking hilarious dude.. Good video too of course

[@levonne766]

👍

[@pyronuggets]

Told me buddy don't slam the door...

[@pyronuggets]

@@shaun4bigblocksllc doors can. Plastic window clamps can't.

[@pyronuggets]

@@shaun4bigblocksllc that's a lot of explaining pal and I respect your answer. I don't know m(any) people who pull the panels off to lubricate anything, but I'll take the advice. Also I've replace the weather stripping and clips (correctly) although I may need to swap the mechanical process out next since I'm still having issues with the window popping out. Haven't really had the pleasure of using these new clips for years yet but I'll work on it lol the old white clips definitely put my friends and I through the ringer with our 86 and 84 s10 trucks

[@chadjay828]

Would those clamps be the reason why my window always falls forward when I tried to roll up or down?

[@pyronuggets]

@@chadjay828 I've recently replaced my clips and I'm now having the same issue you are. I believe it's the other hardware inside the door that holds the window in place.

[@pyronuggets]

@@chadjay828 I've replaced the weather stripping and clips already leaving only the roller and mount. I believe the roller and mounting bracket might not be aligned properly after the new parts were installed so I may as well replace them too since they are old and worn down

[@ronday4210]

😂

[@MrGsxr10001]

I bet you talk like that in front of you gramma? I could'nt watch the whole vid