How to Replace Rear Axle Bearings & Seals 2011-2018 Ram 1500

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/384/gv/Wheel-Bearing...
This video shows you how to install new rear axle bearings & seals on your 2011-2018 Ram 1500. If you hear a grinding or groaning noise while your vehicle is rolling, it might have a worn out wheel bearing. A worn bearing can allow the wheel to wobble, creating a host of other issues. To save yourself from more headaches down the road, replace your bearing right away.
This repair was done on a 2016 Ram 1500 SLT 3.6L Crew Cab Pickup 4-Door 4WD Automatic and the process should be similar on the following vehicles:
2011 Ram 1500
2012 Ram 1500
2013 Ram 1500
2014 Ram 1500
2015 Ram 1500
2016 Ram 1500
2017 Ram 1500
2018 Ram 1500
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/obCK/1AXAA00013
• Pry Bar 1aau.to/o58/1AXAA00020
• 13mm Socket 1aau.to/obX2/1AXAA00015
• 21mm Socket
• 22mm Socket 1aau.to/orn/1AXAA00266
• 8mm Socket 1aau.to/obAB/1AXAA00017
• Bearing Puller
• Brake Caliper Hanger 1aau.to/omD/1AXAA00439
• Seal Puller 1aau.to/on/1AXAA00040
• Slide Hammer
• Ratchet 1aau.to/ob2B/1AXAA00016
• Torque Wrench 1aau.to/oa5n/1AXAA00044
• Anti-Seize Grease
• Block of Wood
• Brake Parts Cleaner
• Cloth Rags 1aau.to/oLI/1AXSS00035
• Copper Anti-Seize
• Gear Oil
• Gloves 1aau.to/oaRT/1AXSS00048
• Pipe Thread Sealer
• RTV
• Safety Glasses
• 14mm Hex Socket
• Drain Pan
• Floor Jack 1aau.to/oar5/1AXAA00068
• Hammer
• Jack Stands 1aau.to/oaed/1AXAA00065
• Magnet - Extendable
• Razor Blade / Gasket Scraper
• Wheel Chocks
Subscribe: / @1aauto
Check out our playlist:
Ram 1500 3rd Generation 2011-2018: • Ram 1500 3rd Generatio...
For More Info visit us at 1aau.to/h/fKw/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Visit-1AAuto √ Do it Yourself √ Save Money

[@chrisholmes2888]

Do the bearings make a whining noise when they are going bad I have a 09 ram

[@countrifiedjose7537]

One thing to note. Put in neutral with the truck off. There is a panel that pops off to the bottom of driver side dash. Use a flathead to release latch and pull handle. You will then be able to rotate gears.

[@tonyrossello660]

Super helpful! Saved me about $850.00 Shop quoted me $1000.00

[@keeganbrosseau1092]

A good thing to do is cleaning up your axle shafts with emery cloth fine grit, old seals will make a groove that if not debarred with completely destroy that new seal right away. And you back into the same job

[@keeganbrosseau1092]

De burred*

[@michael184272]

Very interesting and informative.. thanks

[@antman5959]

Good job I appreciate it

[@thomaspetito6923]

Is this the same procedure with with the limited slip diff?

[@goonkieeyeracing1138]

So does the differental pin and that bolt what prevents the c clips from falling off when assembled

[@dalton534]

What RTV are you using?

[@BrockBelcher]

On your website it says it doesn’t fit 2016 and up ?

[@budreimer233]

It started with disk brakes in the back then went to drum brakes

[@donaldrippetoe5246]

Another really informative video! This is a really great channel! Super helpful! I had the same question as @chrisholmes2888? I have a harmonic/whining noise in my truck that I am having trouble figuring out?