Finally getting around to installing the boost control solenoid. This is very easy to do. Hopefully this will get us in the ball park on the launch. Thanks For Watching!
Пікірлер: 34
@joshwynn4573 жыл бұрын
By far the best explanation I've seen, and I've been confused a bunch!lol. This is my 1st turbo build, I went and bought a vacuum block and was going to plumb it that way...but then reading further into instructions, rather than listening to what people say, I found I need positive pressure to go to Mac valve off the turbo, not a vacuum block... still confused, just not as bad!lol Doing a 99 Camaro SS
@head240t64 жыл бұрын
Simple but great informative video!
@fox-body4 жыл бұрын
Thanks!
@alphagtr884 жыл бұрын
Thanks a lot for the video, informative and helpful 👍🏽
@abesaiya2 жыл бұрын
Nice build 👌 yeah ended up using some stainless quick disconnects for the gate...the plastic ones didn't last for me.
@BigRichEHhthang1003 жыл бұрын
Love to see your set up
@StageMvideos5 күн бұрын
I would love a link to the kit you found on eBay!
@nak_attack3 ай бұрын
Does my pressure source have to come from the turbo housing? My turbo currently does not have a port, nor one pre tapped that needs to be drilled out. So I’m wondering if I need to make a hole and tap it to be able to use my boost controller
@fox-body3 ай бұрын
Probably any where along the charge pipe would be fine.
@CaptainCurt074 жыл бұрын
Really sweet job u done! Curious size of garage I built one few yrs back n I like how tall urs is (18’ tall?) I’m trying find a property like urs! What state Florida? Great information n masterpiece 👍🏼
@fox-body4 жыл бұрын
The building is 24x40. Yes I’m in central Florida.
@FaisalAlhebshiSEPTEMBER15 Жыл бұрын
Hi man , thanks for the vedio it's help alot. I have a question about turbocharger. Have you used ebay turbo especially those made in China 🇨🇳, like to know your opinion about. I'm looking to do single turbo and maximum pressure I'm looking for is 21 psi.
@fox-body Жыл бұрын
I have not used them
@oleksakd2 жыл бұрын
How would you plumb it with a dual wastegate set up
@88thorhammer883 жыл бұрын
When you start the engine does the Mac valve start pulsing? Mine only pulsates when I give full throttle while idling ... I connected it just like you did
@fox-body3 жыл бұрын
What do you have it wired to? The ecu or external boost controller tells it when to pulse based of map pressure.
@lmenzol Жыл бұрын
Does it matter whether Port one or 2 go to the top port on the wastegate?
@fox-body Жыл бұрын
2 goes to the top of the gate. Maybe you could switch them I haven’t tried.
@jeepwk6.5L Жыл бұрын
So you gain minimal boost by doing this?
@dennysoank7484 Жыл бұрын
Where you connet the wiring thx
@fox-body Жыл бұрын
To the ecu.
@2rawsaul7193 жыл бұрын
How about if you don’t have a compresor fitting on the turbo does engine vacuum work the same ?
@fox-body3 жыл бұрын
It will work but it’s best closer to the turbo. I would Get a fitting and tap and install a port on the turbo housing.
@lorenzoarielbraydensoto51022 жыл бұрын
Hey man are you around I'm having slight issue with my set up and could totally use your help lol
@4739-g9c3 жыл бұрын
Show s video of it operating. I'm looking at the diagram that you're showing and to me it looks like if you apply 10 pounds on top as well as 10 on bottom that cancels itself out. Theoretically you'll have 10 pounds with a 10 lb sping. Or less.
@fox-body3 жыл бұрын
Don’t forget the spring pressure. 10 pounds to the top of the gate + 10 pound spring. 20 pounds of boost.
@littleherms32853 жыл бұрын
@@fox-body no, you have 10psi on the dome and 10psi under the dome... essentially zero. That's the same thing as pulling all the reference lines off the wastegate and just letting the spring do it all, usually a bit more than double what the fully referenced pressure would be. (IE: 10psi is the least it will make and 22psi is the most it will make) Now, if you plumb the exhaust on the MAC valve to to dome with a bleed hole drilled into the fitting (.040") you will then be removing boost reference from the bottom and then adding it to the top. Put in your 1.5psi spring and make 4psi down low and 30 psi up top if you want. Want less up top? Drill the bleed hole bigger. Same as a 4 port MAC set up but with a bit better resolution.
@littleherms32853 жыл бұрын
The spring pressure rating on the spring is a fully referenced #. As in, you have a line hooked up to the bottom of the gate diaphram. No line reference is the max the spring can give you. With the green 14lb spring I had I would get 9psi referenced and 20psi non referenced. So... kinda out to lunch. Every turbo system is dynamic and will give you different boost set points on the same spring.