#2 Logic Gates using Tinkercad

[@ElectronicswithProfMughal]

Dear All, at around 12:07, due to some technical issues the video went blank. Just make sure that the resistor is 1k or above, and is placed in the region where it is not overlapping with IC pins. Use a wire if needed. Stop and run simulation again. And that is all :) I hope that you enjoyed the video.

[@fatimahalt8433]

Thank you very much! this was so useful , I'm from KSA and I have lap quiz in digital course today, your video helped me a lot.

[@ElectronicswithProfMughal]

Fatimah alt Glad that you find it useful :)

[@Ritika-Das]

Thank you so much Sir. I had no idea about how to connect ICs using power supply and could only make them with pen and paper. I am hoping to ace my competition because of your help.😊

[@ElectronicswithProfMughal]

Ritika Das Glad that I am able to help Ritika :) Good luck 👍

[@Ritika-Das]

😊❤

[@rin3005]

great video prof Thanks a lot!

[@deepakaddala2083]

Implement using multiplexer F (A, B, C, D) = Σm (1,3, 4, 11, 12, 13, 14, 15)

[@souravidas348]

it's very very helpful for me, thanks.....................................

[@ElectronicswithProfMughal]

Thank you Souravi, glad you liked it.

[@arijitnath3279]

Thank u very much sir... It's a very helpful for me🙏🙏

[@ElectronicswithProfMughal]

Thank you Ariit. Glad you liked it.

[@ElectronicswithProfMughal]

Become a Patron and enjoy the perks including private chat, free, easy, and early access to project files and code. Visit Patreon here ➤ www.patreon.com/Electronicswithprofmughal - Prof. Mughal

[@canyucelkoc509]

Hello sir i need your help, can you show me how to make a’b+ab’ logic on breadboard or tinkercad please

[@ElectronicswithProfMughal]

Dear Can, this expression you mentioned is just simply an exclusive or (XOR) gate expression. You can insert an XOR gate IC and and use pins to give input. Let me know if you have questions.

[@canyucelkoc509]

@@ElectronicswithProfMughal sir i have to do it with 7404,7408,7432 ttl’s and 3 leds,3 220ohm resistance can you help me about that please

[@canyucelkoc509]

@@ElectronicswithProfMughal i would be so happy if you show me how to do it on tinkercad

[@ElectronicswithProfMughal]

@@canyucelkoc509 Dear Can, here you go - kzbin.info/www/bejne/fXO3epaBjN5qqLc

[@TheKidWhoCodes]

Dude thanks, really!

[@ElectronicswithProfMughal]

You're welcome Ahmad.

[@hazelnutmeg3897]

Thanks a lot this was very helpful. I do have a question. Could you explain to me again how you fixed the issue about the broken device due to Current exceeding maximum capacity please? Thank you!

[@ElectronicswithProfMughal]

Adama. W Dear, add a 2.2k resistor in series with the light emitting diode and re-run simulation. And it should work.

[@chadGPTSDE]

Where Can I get this pdf?

[@ElectronicswithProfMughal]

Tanishq, you can visit the website (link in description) and use contact tab, fill the form and make a request.

[@chadGPTSDE]

@@ElectronicswithProfMughal can I please get the exact link to that file here? It's kinda urgent

[@ElectronicswithProfMughal]

@@chadGPTSDE You’ve to follow the process! Visit our website, electronicswithprofmughal.com, go to contact, fill the form and make a request. - Prof. Mughal

[@mohitkumaryadav6563]

Thanks u sir please made orther vedio

[@zbilyo]

ou thank you, i need this, im correting the assesiments

[@laurenshepherd4499]

Youre amazing

[@ElectronicswithProfMughal]

Thank you Lauren.

[@sathyanarayanans5522]

Thank you

[@marianaveed2760]

thank you for this

[@ElectronicswithProfMughal]

Thank you Maria, my pleasure.

[@fredawotwe9848]

The ending part of the video went blank😢. That was the important part for me

[@ElectronicswithProfMughal]

Dear Fred, just make sure that the resistor is 1k or above, and is placed in the region where it is not overlapping with IC pins. Use a wire if needed. Stop and run simulation again. Hope that helps.

[@manishwalia1102]

Thanks sir