20 Drilling Tips for Beginners

[@robertvick6430]

I like to start the drill in reverse first. This will give you an indentation in the wood the size of the drill bit and really helps with tear out.

[@SpecificLove7]

That's an Awesome tip thank you.

[@arashy]

I don’t use a drill very often, so I didn’t know all of these tips. Thanks!

[@TonyyStarrkk1994]

These are all great tips, and good reminders, even for some of us more experienced DIY-ers.

[@SpecificLove7]

Thanks Iron Man

[@kashel83]

The tip about using an envelope was mind blowing, so simple but effective, one of those things I would have never thought of, wish I had known that a few weeks ago when I drilled a bunch of holes in my walls

[@SpecificLove7]

But at least you know now

[@kashel83]

@@SpecificLove7 yes! Honestly your channel is probably the best thing I've found this year

[@charbella]

I agree, wish I'd known about or thought about that years ago.

[@AFizz-cw3on]

Nice! I wish I had these tips 20 years ago. Would have saved me a lot of mistakes.

[@SpecificLove7]

You and me both!

[@markppennington6639]

One way to avoid blowout that I use is to drill most of the way through from one side, then when the point is just beginning to peek through, stop and finish from the back side. You can also drill a small pilot hole all the way through your material and drill halfway from each side.

[@cornpop7805]

A little more about the high/low switch on most drills: high not only goes faster (good for smaller bits), but it also has less maximum torque. The low setting is better for larger bits, as they require less speed and require more torque.

[@SpecificLove7]

Thank you very much for the additional tips and clearing up any confusion.

[@melissak8350]

Im so overwhelmed by all the videos on youtube, as a newbie in woodworking your videos are less intimidating 😂Thank you so much for the tips !

[@sharonkirkaldy8776]

All of your tips are wonderful

[@KatherineAsuncion]

Thank you! I am trying to install a closet system and wanted to make a big hole for my anchors. Now I know to start small and gradually build up

[@cornpop7805]

A different way to use the next size up hole-saw, is to fasten a thin board to the original piece, then use the same smaller hole saw, just enough allow the pilot bit to penetrate, thereby reestablishing the center. Then use the larger whole saw. Easy-peasy.

[@markrobinson9956]

Love.these getting back to the fundamental videos. Keep up the great teaching!

[@SpecificLove7]

Thanks Mark

[@MoranGuyVideos]

great refresh video !

[@mikeATgrowintheglass]

I was searching for French cleats a couple of weeks ago and stumbled across your channel. What an incredible find! After the first of I think 8 (?) in that series, I immediately subscribed. Your presentation is fantastic. Keep up the great work! I knew a lot of the content in this video already, but definitely learned a few things. More importantly, however, I'll be sharing this with my kids.

[@SpecificLove7]

Thanks Mike. You taking the time to share this with your kids definitely means a lot.

[@krisregensberg8063]

Thank you for the tips, some I knew and a lot I didn't.

[@SpecificLove7]

I am so happy it helped you

[@doozerakapuckfutin]

Thank you for doing this sir . Much appreciated .

[@katekat1138]

I love your new series. Fabulous tips! 👍

[@ruthie8785]

GREAT TIPS!

[@TheLightHouseLady]

Great teaching videos! All the tips are very helpful.

[@SpecificLove7]

Thank you

[@paulsmith9341]

When using a spade bit just drill enough where the tip pokes through, then finish from the second side.

[@SpecificLove7]

Great idea, thank you Paul

[@connieadams5010]

Thank you sooooo much for the tips!

[@SpecificLove7]

You are very welcome

[@NewYorker8312]

In addition to my many cordless drills, I sometimes like to use the old fashioned egg beater style hand drills. Hand drills have kind of gone out of style, but they have many advantages such as being quieter, safer, not needing batteries, and also fun to use for small projects.

[@paulsmith9341]

Clinton, Nice job!

[@63clairep]

What's the different between an impact drill and my regular drill? LOVE your videos! Specifically, I love that you just get on with it, no "back in the day" stories or flaming intros. You have really helped me. 🙂

[@charlesdavis3595]

You mentioned about eliminating tear out or blow out when drilling holes with Forster bits and spade bits by using a backer board. When using these bits (also works for brad point bits), you can also drill just deep enough into the wood so that the brad point tip just breaks through the opposite side of the wood. Then flip the piece over and drill the hole from the opposite side. You should get a clean hole on both sides of the wood you are drilling into. Also, on hole saws, I saw a tip on another channel that stated that in order to keep the hole saw from burning the wood, you should drill the hole just slightly into the wood with the hole saw and then drill holes that overlap the hole saw cut on the waste side of the hole saw cut mark and then continue drilling the hole with the hole saw. This will give the trapped saw dust a place to go and will reduce friction on the hole saw which causes the hole saw to get hot and burn the wood. Hope this will also help.

[@SpecificLove7]

Great suggestion, I never would have thought of that one. Thank you Charles.

[@katherineskrzynecki3347]

Awesome! TY so much!!

[@SpecificLove7]

So glad it could help you

[@danbelzile4203]

You do good tips as allways.👍👍 u know what you doing.🍻🍻🇨🇦

[@SpecificLove7]

Thank you very much Dan

[@charbella]

There were some really great tips I'd never heard if before - thank you for these beginners series! I'm wondering how often I should buy new bits? And how do I know when I need to buy new ones? Thanks

[@SpecificLove7]

The best indication of knowing when a bit is turning dull is when you feel that you have to push harder to get the bit to cut. Most bits should only require light pressure to drill into wood. As for how often, it really depends on the quality of the bits and what you are drilling into most often.

[@giorgosroumeli4782]

Super Video

[@harel3am1997]

About the last tip, You can knock with a hammer on the tip of the nail and flatten it a bit then the nail will not split the wood

[@SpecificLove7]

That is definitely a good tip,

[@pleappleappleap]

Instead of just putting a single layer of masking tape on your drill bit, if you put a whole bunch of tape on there, it will act as a physical stop. They make depth stops that attach to your bit with a set screw, but I find that using a 1/8" thickness wrap of tape works more than well enough. Works really well for a drill press too.

[@chrisd2548]

I have many bits mixed together and dont know which are for wood, metal or concrete. If there any easy way to tell looking at the bits?

[@pleappleappleap]

You don't need a sacrificial board for breakout. You can just put a few pieces of painters' tape on there. Or you can drill from both sides.

[@lepoloo]

Lol! When you explain it's better to use a center punch before drilling a hole, make sure you don't miss the cross you've drawn with your awl :D

[@SpecificLove7]

Very true.

[@anonymousperson4363]

For #17, if your hole saws can be combined, place the original hole saw inside the larger one and use it as a guide.

[@terristroh3965]

For #4, I use a Phillips head screwdriver and give it a tap with my hand or light hammer.

[@SpecificLove7]

That can definitely work too

[@DaleLefflerCLC]

I Like your 20 tips! I would think you would start out with the basics. Accurate Measurings and Markings, on to securing your work (for safety and accuracy) then Cutting, (hand tool & electric) straight, angles, curves including holes, and finally, fastening. Lastly finishing and finishes. How 'bout them apples? Keep up the good solid & safe tips.

[@SpecificLove7]

Thank you Dale

[@lstephaniechung]

What is torque?

[@elye3701]

01 Aren't there special bits for wood? 02 What about cutting oil for drilling metal. Any substitutes? 03 How do you drill holes in thin metal sheet? 04 How do you drill lead{battery terminals} without jamming and breaking the bit? 05 Which bits are good for plastic/acrylic/glass/tiles ? 06 How do you use multi-step drill bits?

[@SpecificLove7]

Thank you for the questions to think about

[@itsnetts]

1. Yes there's special spade types for wood, as well as your standard multi-use drill bits. 2. Any oil/lubricant you have is better than nothing. I just use old chainsaw oil for my hobbyist needs. 3. Same way you drill other materials. Might be a good idea to have a backing material like wood behind to prevent warping the plate. 4. For small bits go fast rpm but advance slowly, let it cool off if it gets hot. Also make sure to keep it straight. 5. Plastic and acrylic can just be cut with the universal drill bits, no problem, idk about glass or tiles though. 6. Pretty much the same way any other drill, only this one you drill until you have reached the desired diameter.

[@elye3701]

@@itsnetts Thanks.

[@pleappleappleap]

Hole saws are *extremely* dangerous. Make sure you use a side handle on your drill. Kickback can send the drill at your head or chest, or break your hand. Ask me how I know.

[@pleappleappleap]

Don't use a hammer drill on concrete. Use a rotary hammer. It makes it much easier. It's worth it to rent one if you have to. Much easier your hands and wrists.

[@wolfman75]

👍😎😃🙏👏

[@GNU_Linux_for_good]

11:15 I'll take my tongue to cool off that glowing nail.

[@3rdworldgamer495]

Use Cutting fluid/oil/paste. Don't ever use water!

[@SpecificLove7]

I'm intrigued, why not?

[@3rdworldgamer495]

@@SpecificLove7 It promotes corrosion(first reason that comes to mind). Now I do realise you are specifically refering to wood working or working with wood but it is still bad for the drill bit not to mention the many possible contaminates found in water.

[@SpecificLove7]

That makes sense, and thank you for the clarity

[@3rdworldgamer495]

@@SpecificLove7 cool and great Video

[@defuller1]

On the other hand if you want a nice finish on your work piece you don't want oil soaking into it.