2001 F350 7.3 Powerstroke - 33psi Billet Wastegate Upgrade - Install, Review, Stock WG Compare SP

After trying the stock WG being disconnected, i decided to buy this billet WG on ebay and see what it will do. One thing i think i noticed it spools up the turbo faster because it doesnt start releasing pressure at low psi numbers like the stock one is, but i also like the fact that it doesnt boost the turbo up above 25 psi, i was worried that it would let it boost to 30-35 psi because that would be bad on the stock turbo lol . It did need a little modification to the rod connector to the wastegate, i dont know why they made it so thick to where you cant even put the retainer pin on to hold the rod in place, but only a slight modification fixed that problem. Get yourself a couple retainer clips at local auto store if they sell them, you will need 1 or 2 haha.
33psi Wastegate amzn.to/3J99i75
📺Subscribe and hit the notification bell! ► bit.ly/2W4e5BN
🛠FixitNicks Tools and Parts
1. Amazon Garage ►amzn.to/2QlHZdO
2. F350 List of Parts used: amzn.to/2JQ2MXo
3. Silverado List of Parts used: amzn.to/30qD7KJ
4. My Tool Box: amzn.to/2VzhaVQ
5. Battery Jumper: amzn.to/30wryBq
6. BlueDriver OBDII Scanner: amzn.to/2WaNlQ4
7. Milwaukee Brushless 3/8" Ratchet: amzn.to/2QanthL
🎥Things I use to make Videos
2. DJI Osmo Pocket: amzn.to/2LUtOzr
3. Insta360 One X: amzn.to/2Yy64T2
4. Samsung 128GB Micro SD: amzn.to/2YwT9AE
5. iPhone 8 Plus 256GB: amzn.to/2LSvj16
6. iMovie or LumaFusion for editing (App Store
🔥FixitNick Shirts and Merch ► bit.ly/2Vu8v7e
FixitNick on Social:
Facebook ► / fixitnick81
Instagram ► / fixitnick
Email ► [e-mail]
PROJECT COST:
2001 F350 7.3 4x4 6 Speed Dually
135,000 Miles
F350 Auction bid - $5,700
Auction fees - $540
Delivery cost - $650
•REPAIRS•
New wheel - $310
New rear tire - $130
New front tire - $130
F350 Pair of leaf springs - $240
F350 RH leaf spring sold - (-$60)
eBay Driver dually fender - $450
eBay Driver dually fender refund - (-$400)
eBay Driver duality Fender sold - (-$120)
Another Drive Dually fender - $400
Taillight - $20
Motorcraft water pump - $180 amzn.to/2TAmYPK
2 new Napa batteries - $300
Dorman Mirror Switch - $15 amzn.to/2OZDQAT
Motorcraft Steering Stabilizer - $70 amzn.to/2yYpMN9
•UPGRADES•
Floor mats - $30
Tailgate Assist kit - $50 amzn.to/2Z4vImd
2" level kit - $60 amzn.to/2N8ecay
New side market lights - $35 amzn.to/2Z3nEyh
New Clearance lights - $30 amzn.to/33BWSjR
Red & Amber LED Bulbs X20 - $50 amzn.to/2YRZBam
White LED Bulbs X10 - $15 amzn.to/2YRhg1D
3 LED Rear Bar - $10 amzn.to/2ZaSadv
LED flasher relay - $15 amzn.to/31JCfjQ
LED headlights - $150 (i didnt like the fit)
LED foglight - $120 (i didnt like the fit)
Motorcraft oil filter - $10 amzn.to/2N8yhNK
Motorcraft fuel filter - $20 amzn.to/2OWVcOE
Amazon 5W-40 Full synthetic oil - $75 amzn.to/2Z8DuHE
AIH delete plug - $20 bit.ly/2H9DocO
Thermostat and Housing - $70 amzn.to/2NaKFwL
New radiator hose - $15 bit.ly/2Z9kX2e
Bed Back rack - $250 amzn.to/31IDVKI
Fomoto Oil pan drain valve - $25 amzn.to/2H8D8ec
CCV Mod - $40
Intercooler pipe foil delete - $0
Intercooler pipe wrap - $20 amzn.to/3050CrW
Tyger side steps - $350 amzn.to/2YUArrq
Bosch 135A alternator - $160 amzn.to/33Efn7q
Boost Gauge install - $70 amzn.to/2Z3opY9
Stealth Tuner Module - $600 bit.ly/2MljLTp
EBP pipe & sensor clean - $0
5” AFE straight pipe exhaust - $650 1023diesel.com
RiffRaff 6637 Intake kit - $100 bit.ly/33ARBcn
RiffRaff FRX Fuel upgrade - $200 bit.ly/33yZHlM
RiffRaff Crossover oil line - $50 bit.ly/2Z8F4JA
RiffRaff up-pipes upgrade - $400 bit.ly/2KCv9Iv
RiffRaff Plenums upgrade - $300 bit.ly/3066Ck9
2015 Interior Seats up - $1,100
New carpet from StockInteriors - $160
33psi Billet Wastegate upgrade - $60
TOTAL COST: $13,120

[@FixItNick]

FixitNicks Tools and Parts 1. Amazon Garage ►amzn.to/2QlHZdO 2. F350 List of Parts used: amzn.to/2JQ2MXo 3. Silverado List of Parts used: amzn.to/30qD7KJ 4. My Tool Box: amzn.to/2VzhaVQ 5. Battery Jumper: amzn.to/30wryBq 6. BlueDriver OBDII Scanner: amzn.to/2WaNlQ4 7. Milwaukee Brushless 3/8" Ratchet: amzn.to/2QanthL 📺Subscribe and hit the notification bell! ► bit.ly/2W4e5BN 🎥Things I use to make Video 2. DJI Osmo Pocket: amzn.to/2LUtOzr 3. Insta360 One X: amzn.to/2Yy64T2 4. Samsung 128GB Micro SD: amzn.to/2YwT9AE 5. iPhone 8 Plus 256GB: amzn.to/2LSvj16 6. iMovie or LumaFusion for editing (App Store) 🔥FixitNick Shirts and Merch ► bit.ly/2Vu8v7e FixitNick on Social: Facebook ► facebook.com/fixitnick81 Instagram ► instagram.com/fixitnick Email ► [e-mail]

[@bigpeterbilt379]

Your clip was laying on the turbo

[@bigpeterbilt379]

Check the video at 5:14

[@miguelmacedo1926]

7.3

[@hectiicvirus8576]

@fixitnick, put the truck under a load like with a heavy trailer, and he if it makes a difference, also try to make the truck pull more air in with a tune.

[@alexnavarro6326]

I bought one the same as yours but the adjustment bar of the old one is shorter than the new one and ahu giving all the adjustment to make it as short as possible, it is still a bit long, what can I do about it?

[@keanuarmstrong6157]

hey nick great video i know you made this a while ago but it was great instruction. As a marine mechanic i saw this and did actually found why you are not creating more than 25 psi, your map sensor has a dump load setting on it that is stock on the vehicle and can be disabled with a boost fooler. this is if you want to create more than 25 psi, to find this info i did it myself and ordered a waste gate and a fooler and created almost 35 psi. you probably know this by now but thought id throw it out there. great vid

[@thane924]

Same 36 psi

[@Southrn_Maniacyago]

22 psi here

[@Bwanar1]

Correct about the fooler, but also it may not have been adjusted properly for his truck. I may have been opening as far as that setting is effected, by the gate. You can shorten the rod by turning the adjusting connection. Shortening it makes your pressure build sooner, thus allowing more boost fully open.

[@RCAddictdez]

I would assume the reason why you are only getting to 22-23 psi is due to not having a tune/boost fooler, when the computer reads a certain psi (in this case 22-23psi) it will cut fuel to a lower duty cycle to prevent overboost

[@tedenderpalmer6550]

Never thought of changing the boost waist gate. Being an old aircraft mechanic think I would replace the clip with a wrap of safety wire. Interesting to know how this effects turbo lag. Paper towels, what a great idea. Nick I cover my engine with old pillows when I lay on it, much more comfortable. Your testing is always interesting to me, it's real time data.

[@FixItNick]

Stock clip is impossible to wrap no gap there

[@sonicbob7127]

Hello Nick. I'm thinking the reason that your only seeing 22 - 23 pounds of boost is when the map sensor sees 22 pounds it defuels the engine. That's why your repeatedly seeing the 22-23 lbs. The map sensor is working. I ordered a new 1/4" mini pressure regulator (like 10 or 12 bucks) and put two 1/4" barb connectors on it and preset it to 20 lbs. Then I cut the map sensor line about half way between the map sensor and the slip on connector on the intake spider and mounted it there. So now when I mash on it. The map sensor only sees the preset 20lbs but the boost gauge will continue to climb. BUT! You really need a EGT gauge to keep an eye on those exhaust temps now. Keep it below 1300° . Also need a fuel pressure gauge. I know you put 70 & 70+ pound springs in the fuel return but if the pump is weak and supply may be low as well. Thus the fuel pressure gauge will tell you. It takes fuel to make power. Peace.

[@FixItNick]

I think I’ll just have to turn in rod every turn is like 1 psi

[@sonicbob7127]

@@FixItNick That's great but it will not stop it from defueling. When the map sensor sees 23 pounds of boost it sends this information to the trucks ECM . Then the ECM defuels the motor so that it will only boost to 22 pounds. You can buy a boost fooler like this shop.fullforcediesel.com/boost-fooler but I built mine just like it for 15 bucks. Then just preset the regulator to twenty pounds and your good to go.

[@josephoverstreet5584]

@@FixItNick he’s right

[@FixItNick]

Sorry guys for uploading so late, but I got it done whew!! Editing takes X10 longer than actual mod itself haha

[@twayland6186]

Tell your son to age faster so he can start doing it for you

[@GODLYSTXRMS]

Hey does this wastegate work on the obs 7.3's ?

[@stevenwichin1259]

My 7.3 would love a new wastegate 😍 thanks for the opportunity!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@stevenwichin1259]

FixItNick sweet! Thanks man! Love the videos😌😌😌

[@jusmike1983]

2000 F250 7.Tree with 205k miles and a 2001 F450 8.Tree with 315k miles. I would be very appreciative for the waste gate. Nice Videos Nick and sweet truck you got. I enjoy your videos I get a lot of good info from them and I'll continue to watch and learn. Thank man!

[@jusmike1983]

That was supposed to be F450 "7"Tree, not 8

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@samuelyi9189]

2001 7.3 here. My first truck I bought and fixed up myself. Did injector cups. Injector seals. Oil cooler. UVCH. Coolant Filter. intake. etc. Would Love to win the 7.3 waste gate Nick! You know how it is at 16 years old!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@samuelyi9189]

FixItNick Thank you!

[@peepingtom9148]

I would love a new 33 psi, Wastegate, for my 7.3L Powerstroke.

[@FixItNick]

Copy that

[@andrewcavazos70]

FixItNick me too!!!

[@enriquegarcia2459]

Love your videos Nick! I just ordered 33psi billet wastegate. I have the edge chip on my truck . 2001 Ford F-350 7.3 diesel. I also removed my air box and put in a K&N filter. I know it’s not as good as the SB filter. I like it though. Thank you for your videos.

[@desertdieselgang7985]

If the truck is stock tune 7.3l won’t produce enough fuel to get to 33 psi my truck has a 33 psi watergate with 80hp tune and builds 35psi

[@tiktatttoe]

What do I need to buy to produce more power from stock engine

[@desertdieselgang7985]

@@tiktatttoe go to power stroke help on KZbin watch the 7.3l fuel mods. It’s a good first step and is all free. After that if you want more fuel it would be a lift pump and injectors

[@desertdieselgang7985]

@@tiktatttoe also a tuner is a must if you want big power but you need a exhaust and intake before that

[@DIYWellcraft196]

We can see your retainer clip It's laying on the back of the Turbo right behind where is came from just look closely @20:13 time frame, you'll see it too

[@johnharding1538]

Exhaust pressure is assisting boost pressure on the diaphragm as exhaust pressure flowing against wastegate is why the 30psi dropped to the 23psi. Im running 42psi out of my 7.3 at 650hp.

[@DeepSouthBayouDiesel]

🤯...I hope your engine is built for that kinda power.

[@Markypoo1331]

I run Riff Raff’s OCR. It Will trick the map sensor into thinking it’s not reading max boost. Therefore not defueling and allowing you to reach a little more boost then 22 or 23 psi. Even when I had a stock turbo I still got around 26 PSI. ... I hope that helps buddy 😎

[@FixItNick]

Thanks man, a hydra would also help I’m trying to get that

[@Markypoo1331]

Yea the Hydras are nice man. I prefer those myself. But I was given a TS 6 Position for free. Couldn’t beat it. But one day I’ll get it. But first a fuel system overhaul. Lol

[@bryanstidham3187]

7.3 wastage grate. Would love to have a 33psi wasn’t gate. The old retainer clip was sitting on the turbo next to he wastage arm. You can also just a wastegate arm for more resistance to get more boost

[@bryanstidham3187]

The TS performance six position tuner is awesome would highly recommend it

[@FixItNick]

Haha I saw it in the vid... but actually that was my first one I made after stock one flew away... I’m sure it fell off already on way to work lol

[@FixItNick]

Yea I might turn the rod 1-2 tines, 1 turn = about 1 psi

[@mitch7.3powerstroke81]

Change your tuning. I have superchips. Went from what you have to about 30. I also have the gtp38r. My boost stayed low 20’s until the tuning changed.

[@FixItNick]

I got no tune wanna get hydra

[@stevenbrantner2435]

The reason why it never built more than 23psi is because a wastegate needs to be preloaded to work properly try shorting the rod 1 turn at a time until you get the desired boost.

[@francishartman7749]

Great instructional video! It seems you need a tuner (Hydra or T6) and a boost fooler to get past 22psi. Cool wastegate! 🖒😉🔧🔩

[@FixItNick]

Thx, yup want hydra, hydra will fix all issues

[@stevenmcc2119]

No to t6 these 7.3 love the hydra and it’s well worth the money spent

[@RCAddictdez]

It's probably de-fueling, once the computer reaches a certain psi without the boost fooler it defuels the engine to prevent overboost

[@dryslick09]

The part of your video 5:09 minites in, while you are showing the step on the pin, you can see your lost clip laying right there, on the turbo.

[@mikesomers7193]

I noticed it too! Lol

[@timallen5483]

Who would thumbs down this video?! Great video man, well done.

[@dopesquatch]

Late 99 stock turbo 4inch down pipe 5inch after larger air cleaner international up pipes dp tuner on 140 tune automatic trans 32 pounds with the red line pulled off...

[@johnoehrlein8379]

Use a magnet on them little clips, I did and it didn't get away from me. Nice job.

[@FixItNick]

Thx bro,

[@dockilljoy9017]

Little late but the clip, it’s in the frame of you showing us the post for waste gate

[@84EMendez]

Know old video but I seen the retainer clip when u showed how u molded it (@5:14)😂😂

[@Tommy2xV]

Did you see your clip? It’s in the shot when you show the bolts for the waste gate!!??!! I would love to have that waste gate, it would be my first mod. Love the videos, keep it up brotha

[@mattleonard5268]

Your truck needs more fueling to push the turbo harder and achieve the 33psi boost

[@Bigtree06]

I would like a Newish 33psi wastegate for my 7.3, yeah buddy!!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@patparker2000]

7.3 wastegate, would be awesome to get since I already have my 7.3 in a million Pieces, had the Hpop and turbo pedestal blow and a fuel bowl leak all decided to happen at the same time

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@francishartman7749]

It still be interesting to first put the boost fooler and see how much boost you will get. Then put the tuner and see how much more boost you will get.

[@FixItNick]

Boost fooler would just fix engine light code I think

[@obs_community9517]

My friend lost his retainer pin went in his truck and found a Bobby pin and was like this’ll work till we get home let’s just say it’s worked since last January

[@FixItNick]

Lol good one

[@richardromano4086]

FixItNick, if you look at your video at 5:12 you will see your old retainer clip behind the turbo wastegate operation lever, and you might want to get back in there and check the jam nut on the rod

[@LemonySnicket-EUC]

He posted in here that he saw that in the video as well. Good eye.

[@alanarmstrong2323]

I preloaded wastegate 3 turns after nutral but what a change the biigest improvement on top of everything.

[@FixItNick]

Yea I was thinking to turn in maybe 1-2 tines, each turn would be about 1 psi

[@austinpaul2170]

Adjust the waiste gate ! And you will get more boost ! 6 to 8 full turns !

[@erichn4291]

Check out the map fooler. The map will control the blow off but the stock does the same.

[@FixItNick]

I want to get a hydra

[@fatfairlane]

Shorten the actuator rod. For every one turn inward is 1 pound of boost so for 1 full pound do 1 full turn on the actuator arm where it attaches to the Turbo.

[@FixItNick]

Yes correct, after get Tuner

[@fatfairlane]

@@FixItNick get the hydra. It truly is a amazing tuner for our trucks

[@FixItNick]

313dieselguy yes I agree

[@jackhumble4867]

I love the video im new to you tube im just a old fart but i gotta say i like your attitude very well manners very thorough no arrogance and very humble guy thank you for sharing it very helpful... Us old guys love humble learnings... Keep the video's comming...

[@Hewardrv8]

Ps: stick a magnet back there next time you take e clip off right next to it and magnet will suck it up when it pops off! Also, try adjusting the rod length if you want a bit more psi/open later should see a bit higher psi. If you really want higher psi you would need a different housing/compressor wheel and atleast a 360* oil ring in oil housing.

[@FixItNick]

Maybe later on after Tuner

[@Hewardrv8]

@@FixItNick you don't need a tuner if you do the turbo work! A lot cheaper and much better than forcing fuel into the cylinders! I just completely rebuilt my turbo, fuel system, hpop added xover line among other things myself! If you need any advice or help feel free to shoot me a message. I absolutely love these 7.3l engines amazing feats of engineering, they last forever!!!

[@TheGr8Ox]

7.3 wastegate!!!!! Would be a great addition to my excursion 7.3

[@FixItNick]

Copy that

[@Cross-EyedCyclopsBear]

You need more preload on the actuator, about a 1/4 inch..boost it up 😁,love the video brother 👍

[@benjaminday1470]

22 psi is controlled by the factory ecu. You will not get more then that without a tuner. Above 23 psi you will get a check engine light for overboost. Once you do a tuner you will need an electronic boost cooler to not allow the map sensor to see over 23 psi then with ur mechanical boost gauge u will be able to view actual boost

[@benjaminday1470]

Throw a tuner on there and watch how fast that boost will climb with that wastegate😎 great stuff man keep it up!

[@FixItNick]

It would boost more, I saw 25 with stock one unplugged , every turn in on rod 1 psi, hydra will fix all probs lol

[@benjaminday1470]

FixItNick can’t wait to see it man! Also sorry I somehow missed the video where u already did a 5” exhaust! She’s perfect!

[@jamesgilstrap6969]

U need a boost fooler i get around 25 to 28 psi with my old waste gate

[@FixItNick]

Have Tuner?

[@stephenlane7951]

Any issues with running that high psi with otherwise stock motor?

[@erichn4291]

To do this better a run with the stock then a run with the new with the gage attached so we could see the return on investment.

[@zacschmitt1441]

You can buy assorted size c clips at harbor freight for a few dollars and there’s one that fits perfect I had the same issue but happened to have the box of c clips laying around the shop

[@FixItNick]

I been trying to make it out there to get a pack lol

[@jaketherattlesnake135]

One of my old trucks had a wicked wheel and a cold air intake and a ts6 tuner it spooled up to 32psi real quick

[@FixItNick]

We see what Tuner gets

[@leomartell8818]

7.3 ford excursion like your videos very well made and easy to follow instructions

[@FixItNick]

Got it, thx man

[@shanemartinson5006]

I have the same type that I ordered on line and haven't put on cause I'm upgrading my turbo soon, but...… 1st you need a boost fooler to get higher psi, your truck wont let it get higher, and 2nd you didn't preload the waste gate spring.... most waste gate need up to 6 turns on the rod to preload, from all the research I've done

[@FixItNick]

I’m currently happy where it’s at 23 psi, boost fooler only prevents engine light code I think but if i preload WD more it will get more boost no problem. I wanna get a hydra so that would help with light and boost

[@shanemartinson5006]

I just installed mine and only preloaded mine 2.5 turns and I'm getting 25lbs, and no light.

[@FixItNick]

Shane Martinson I get light after few pulls then goes away

[@bxtbill]

Sorry I know it's been a while but my question is how do to get the e clip out I've been fighting with it but can't get it off

[@LemonySnicket-EUC]

You need to hook the loop side of the clip with your pick and carefully slide it out. I'm sure you probably already figured it out but this might help others.

[@kirkharrell7726]

Is that the retainer clip laying on your turbo? Watch the new control arm fit demonstration.

[@FixItNick]

Yes haha

[@wilsonbaird]

You need to adjust the rod to have a higher PSI

[@phillipcook7843]

Or adjust the original waste gate rod... here's another try. Put brake to the floor and Rev her to 3200 rpm and watch the harbor freight boost guage...lol

[@philliplawson2001]

I'm pretty sure you can use E-CLIPS for that actuator.

[@jonbarnes5690]

You most likely don't have enough fuel on that tune to push past the 23 psi. But thank you for the review I need a new gate and was looking at this exact one.

[@FixItNick]

Yes probably, need tune

[@henryg22250]

I would really love a new waste gate for my 2003 late 7.3. Nice video btw. Greetings from Texas

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@branderiffic8623]

Fixitnick we have the same truck same year and all ive already done injector cups on mine and a new waterpump and ive has the wastegate disconnect for a while i would like to have it 7.3 turbo diesel for life

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@juanf4739]

Put a magnet near the clip area

[@omardinunzio5552]

I went to install the Big Head waste gate actuator and it wouldn’t adjust small enough for my stock Turbo,

[@MrLynch75]

The retainer clip was a 1/4" away sitting on the turbo,....so close. Please put me in for the wastegate.

[@FixItNick]

Haha I saw it in the vid... but actually that was my first one I made after stock one flew away... I’m sure it fell off already on way to work lol

[@MrLynch75]

@@FixItNick Don't forget to enter me in the contest. About to install up pipes, what a perfect time to make this addition. Thanks man.

[@adamkeith7893]

Your computer automatically de-fuels at 23 psi. The only circumvent is an overboost code regulator. You can find the best one on the market made by Riffraff Diesel. Have one on my truck with a Banks Big Head wastegate and I see 30 psi no problem.

[@FixItNick]

Yea I need a tuner will fix all that

[@azahelresendiz]

I purchased the same part and what I did on mine Was make it thinner with the grinder

[@FixItNick]

Yea that’s another good options as well, I figure this was faster and I’ll probably thinner out the other piece cuz it came with 2

[@ltbaldwin]

hey Nick, I really like your videos as I also have a 02 7.3. I would love to have that extra waste gate!! Thanks for what you do!!!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@KingRanchW]

I want the 7.3 waste gate I would love to have it my dad would love to have it the truck needs more boost

[@FixItNick]

Got it

[@SDycus]

I'd love an aftermarket 7.3 wastegate.

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@hellcat3268]

I dont have a car but im working on my e bike very hard to do because i dont have that much tools. Btw every vid u post makes my day

[@FixItNick]

Thank you bro, me and kids will be working on few E bikes soon on the channel :)

[@mmaxsonify]

Watch your video you'll see the retainer clip is laying right there on top of your turbo

[@mattlane5323]

Wastegate 7.3 would be a big help to my build

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@stevenmcc2119]

How long has it been on truck and does it still do a good job ?

[@crazyjayb7817]

Would love a newish 7.3 waste gate

[@nathanneff6229]

Your retainer pin was laying right there beside the waste gate lever

[@nathanneff6229]

Pause the video at 5:10 you will see it

[@FixItNick]

Yea I know kinda dumb haha, couldn’t see it in person but in vid could see

[@WrenchDaily]

Hey FixItNick ! I would like to have the 7.3 WasteGate for my other project. Thank you 😊

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@DennisBohannan]

Probably defueling if you do not have a boost fooler.

[@FixItNick]

Yes likely, I need a tuner!

[@isarob03]

I’d love that 7.3 wastegate for my f250 I just bought. Give her some pep in her step

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@isarob03]

FixItNick how would you be contacting the winner again? Just so I can keep an eye out...

[@FixItNick]

Isaiah Robinson I’ll announce it a next F350 vid

[@jimv3352]

If you haven't given the "extra" wastegate away yet, please add me to the drawing. By the way, your retainer clip didn't fly away. It's right next to the wastegate arm.

[@FixItNick]

Sorry already gone

[@jeffw2811]

7.3 Wastegate. I would love to put one on my 2002. I don't get anywhere near 22 PSI.

[@skali4nia135]

My 2002 f250 7.3 powerstroke would love that wastegate. Thanks for the videos and keep them coming

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@outdoorliving8254]

That waste gate would look good next to my new turbo on my 7.3

[@FixItNick]

Yes it would lol

[@justin-ng8zs]

7.3 wastgate, Sure count me in on the drawing. Good luck everyone.

[@FixItNick]

Copy

[@robodude169]

Please tell me you found that pin when you watched the video back

[@mooselustig7959]

7.3 waist gate I could use that. I;m a diemaker and can fix the broken bolt

[@AntonioClaudioMichael]

The new waste gate is nice

[@sbfnation2535]

Did you preload the wastegate if not it won’t build the right amount of boost

[@charlesmartell7518]

Very good video I have a 02 7.3 and would like to have a new waste gate

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@TheMotorman8190]

Its turning off the fuel, install boost fooler to get past 22 psi

[@FixItNick]

Yup

[@WalterTamayo]

7.3 Wastegate. My factory stock purple 1999 would appreciate the upgrade

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@ryandelfin656]

Tighten up the tension on the waste gate

[@FixItNick]

After get Tuner

[@jeff.3.2.12]

Was you able to retrieve your clip after seeing it in your videos?

[@FixItNick]

What you mean seeing it in the vid? Oh wIt just watched.... that one is actually my first one I made and also lost haha

[@jeff.3.2.12]

@@FixItNick , look at 4:55, that clip laying by the wastegate arm. Does that look familiar to the clip you made?

[@youjleachjrtube]

Great videos Nick. Would love to have a chance at the 7.3 wastegate. Thanks

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@loganhanneman]

Intrested in the 7.3 wastegate would like to get a little more boost

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@chrisayers8335]

7.3 wastegate. Great videos!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@shanebowlby2378]

7.3 Waste Gate for my 2002 Ford Excursion

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@andrei.b6827]

7.3 wastegate I’m local in Sacramento I’ll pick it up if I win

[@FixItNick]

Copy that

[@jonathanc5117]

I would love to have that 7.3 powerstroke waste gate my stock waste gate don't evan work I'd love to hear the waste gate and build more boost

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@Tommy2xV]

Haha, I thought the date was 2020 sep 21 not 2019. Love the videos bra

[@19TheDan]

The turbo is the problem. It can only make 22/23 psi. Without other upgrades you won't see an increase. Unplugging that red hose will give max pressure. A different Wastegate won't change that.

[@FixItNick]

The stock turbo can do over 30psi actually, it defuels, I need a Tuner

[@tylerdavis288]

How did you get it out?? I cant get the bottom bolt

[@mrpzy45]

7.3 wastegate needed here! Dude even if you were giving away stickers it would be dope.

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@mrpzy45]

Crazy he didn’t reply.

[@phattdaddy2974]

Did you try to unscrew the end of the stock W.G. and see if it would fit on the new W.G. arm?

[@CRIBBSSTUD]

7.3 wasteghate baby lets goooooo

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@Shanemartinez5]

7.3 Wastegate! Would go great with my 38r!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@hudsoncollins3487]

7.3 waste gate! Need it for my 97’ F350 7.3

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video

[@johntaylor2306]

7.3 wastegate! That would be awesome with my KC turbo wheel!

[@FixItNick]

Winner didn’t contact me to get WG I’ll be picking another winner in following up F350 video