Yea... Just had to change mine out. Gotta wiggle the dam thing back and forth to heck and back... Ended up cutting a channel with a Dremel. But that shoots out the metal inside of the sensor. Wear Eye Pro. and expect to shatter the Dremel disk on the littlest mistake. (3 x). then I wiggled it to death to get it off. But some gun grease or whatever you got on that pin before replacing. Man, its smooth and sweet now.
@ggazzara11153 жыл бұрын
My 1999 was seized to the shaft too. Used a dremmel to "V" notch it and pry it off. Easy job.
@CrsPro5 жыл бұрын
I just experienced this. That sensor was so hard to get off. Thanx for the video bro💪
@fancypolak5 жыл бұрын
It was a pain! Thanks for watching!!
@twistedlimb40533 жыл бұрын
Hey thanks! This was the video I was looking for.
@fancypolak3 жыл бұрын
Glad it helped!
@misterbulger4 ай бұрын
Mine is just stuck in park..starts up fine brake lights work... This seems like an easy junkyard snag. Wonder what years it fits? Mines a v10 4r100. Good chance my trans is just grenaded and i don't really wanna blow $90 on a new sensor just to find out. Cant even drive it off a cliff or even tow it! May have to pull the driveshafts to move it...
@fancypolak4 ай бұрын
@@misterbulger best of luck with whatever you end up doing! Even if it involves rolling it down a hill...lol
@danhambrick63316 жыл бұрын
Good old Michigan rust???
@haydengodfrey8147 Жыл бұрын
Any tips for getting the electrical I clipped? Mine stuck
@fancypolak Жыл бұрын
Unfortunately this was a few years ago at this point and I no longer own the truck. The other comments on this video have some decent advice on getting it pulled out as well.
@winstonsmith36853 жыл бұрын
Going through the same thing. Holy shit. It’s like welded to the shaft.
@fancypolak3 жыл бұрын
yeah its ridiculous how stuck on it gets!
@stevenmcc21193 жыл бұрын
How do you get the tab off the white piece that connects the shifter lever....UPDATE.. it’s the cable end that was connected to the shift lever thought it come with the NSS and mine was seized on took a pry bar to get it off and the white inner ring of the neutral safety is still seized on the shift lever of the trans
@fancypolak3 жыл бұрын
I believe that one just slides off the top of it, easier said than done though depending on how much rust you got lol
@dmeads56634 жыл бұрын
Could you use a torch to heat up the stud that it sits on?
@dmeads56634 жыл бұрын
Fancy Polak thanks
@ggazzara11153 жыл бұрын
NO!!! If you do, you'll melt the shaft seal and have big problems!
@jamesnunya9541 Жыл бұрын
Yeah you will melt your shaft seal
@blackisback743 жыл бұрын
So all you used was the crow bar. Mine is frozen on there and been soaking in PB blaster for weeks and still can't get it off.
@fancypolak3 жыл бұрын
thats exactly it, used a crowbar, was bending the crap out of it but eventually it popped off, you could probably cut it off but have to be careful not to nick the stub
@blackisback743 жыл бұрын
@@fancypolak well it worked. Like you I bent the hell out of the side of my trans pan but nothing Critical just cosmetic. Boy was it a bitch to get off though as plastic from the old one was cracking as I was prying it out. Damn swrich caused me to have to also replace my shifter tube and my over drive switch cuz I broke both trying to get it in park.
@fancypolak3 жыл бұрын
@@blackisback74 ayyy congrats! lol it is not an easy job on these older trucks. Glad you got it out though!
@travelerwithpurpose91324 ай бұрын
Gotta doi mine..is it gonna drivers or passenger side
@fancypolak4 ай бұрын
Its been a few years but on mine it was on the drivers side it looks like
@raulsalazar95916 жыл бұрын
What were the symptoms u were having witht it
@fancypolak6 жыл бұрын
Main issue was that the shifter was super difficult to put into any gear and was difficult to line up (ie: you couldn't really feel what gear you had it in P-RND21) and the other issue was occasionally I'd have to jiggle the shifter in park or neutral to get it to start, otherwise it wouldn't crank. Both those issues should be fixed now with this new TRS because now it slides and clicks nicely into gears and I believe the neutral safety switch is built into this device. Thanks for the comment and subscribe! Let me know if you have any other questions.
@raulsalazar95916 жыл бұрын
@@fancypolak thanks bud mine did the same thing the other day had to start it in neutral also od light flashed pulled codes came out for this sensor will replace asap
@fancypolak6 жыл бұрын
@@raulsalazar9591 awesome man, good luck on the replacement!
@CesarHuert19153 жыл бұрын
@@raulsalazar9591 hey raul 2 years later i just bought me a 99 7.3 work truck and od light is flashing its hard to put it in gear so my question is did it ever fix ur od flashing light issue.
@CesarHuert19153 жыл бұрын
@@fancypolak thankz for the vid!!👍
@WhattheVloggity3 жыл бұрын
Was your overdrive light flashing?
@fancypolak3 жыл бұрын
mine was not no
@WhattheVloggity3 жыл бұрын
Interesting mine was
@zukiguy Жыл бұрын
@@WhattheVloggityI know it's been a couple yrs since your comment what all was your transmission doing my overdrive light is flashing and it's sticking in gears and gotta wiggle shifter for park and neutral wondering if yours was similar
@nonagreeable5 жыл бұрын
I'm going through the same thing right now. Feel like I'm going to break it. It's soaking in wd40 now
@fancypolak5 жыл бұрын
Yeah when I replaced it I was bending the living hell out of it until popped off, it was really on there, didn't even end up breaking it. Good luck with it!
@nonagreeable5 жыл бұрын
@@fancypolak If I do break it, you think anything bad would happen? I'm about to just cut it off.
@fancypolak5 жыл бұрын
@@nonagreeable as long as you don't damage the actual metal stub that it slides on to (you can see it's keyed to slip on there), I don't see why it would matter, as long as you already have the replacement.
@nonagreeable5 жыл бұрын
@@fancypolak yeah that's what I'm hoping. Letting it soak tonight and then more prying tomorrow. Thanks for your video.
@fancypolak5 жыл бұрын
@@nonagreeable no prob, good luck with it, let me know how it goes!
@shanebuckles91342 жыл бұрын
Man bro I wish you would have actually showed how to replace it
@fancypolak2 жыл бұрын
it was hard to film and do the work at the same time unfortunately, theres some good advice in the comments as well