Here is how I got my ignition unstuck in my 2005 chevy trailblazer extended
Пікірлер: 48
@seanterry6240 Жыл бұрын
The ignition release on the steering column is actually meant to be able to replace the ignition tumbler and yes this is a temporary fix. But most likely the main problem is in that gear Shift Interlock Solenoid. when the car is in gear the solenoid sends a signal to your ignition telling the ignition that the car is in gear and not to release the key. so if that solenoid is gummed up from spilling to many drinks down into your gear shift that solenoid is probably not disengaging. Simple fix disassemble the gear shift cover enough to spray some cleaner on that solenoid and any luck you won't have to replace the Shift Interlock Solenoid.
@chicagocrazy5740 Жыл бұрын
Does that engages the security light to flash?
@jeffanderson68732 жыл бұрын
Thanks man, like you said, saved me $300! Awesome 'Oh Shit Sunday' vid. This is the exact same prob I had w/ my 2006 T-Blazer
@jeremiahn44556 жыл бұрын
Thx buddy. Worked great for me.
@lucashenry44366 жыл бұрын
Thank you for this video. I have a 2003 Trailblazer that wont release the key from the ignition. It turns over and starts, but the car wont let it release the key causing my battery to stay on. Do you think that as a temporary fix I could press the "release switch" that you mentioned to remove the key? Thank you for your time.
@lucashenry44366 жыл бұрын
it worked! so easy.. thank you.
@bam44446 жыл бұрын
Glad it helped
@tonybowman34545 жыл бұрын
Lucas Henry I need help please
@tonybowman34545 жыл бұрын
bam 444 I need help please
@juans66396 жыл бұрын
I had a similar problem with a 1995 Chevy Silverado in where I could not take the key out. On the third trip to the dealer and having my P.U. for a week, they found that it was a so called "bitsy" cable that was loose and when putting it in park was not taut enough to release the lock on the steering column.
@luisroldan44375 жыл бұрын
I hope this help there is a fuse 10 amp under the left rear seat on the fuse box that read IGN O check it and replace it if necessary that is the common problem for this issue
@luedog83852 жыл бұрын
FU MAN! I JUST RIPPED APART MY WHOLE CAR AND NOW YOU TELL ME
@noahbryant8309 Жыл бұрын
Video helped a lot
@Koldatt Жыл бұрын
Thanks for this!
@johndeaton50852 жыл бұрын
What size torqued to get plastic off bottom of steering wheel
@cody8180 Жыл бұрын
Torch or hammer or big pliers worked for me
@amberhill90634 жыл бұрын
SO SAY FOR INSTANCE I BROME THAT LIL WHITE CYLENDER THAT YOU REMOVED AND THE STRING I SIDE IT WHEN U REMOVE THE TOP SPRUNG ACROSS THE VEHICLE AND OUT THE DOOR LOST FOREVER.MY VEHICLE CRANKS THEN DIES.ITS BEEN 11 MONTHS AND A BUNCH OF SHADE TREE MECHANICS.HELP HELP HELP I NEED MY RIDE TO DRIVE
@erinapple1566 жыл бұрын
Pull the plastic down a little bit under the column, stick your finger on the release pin and push up ☝, use other hand to turn the key back. I've been fingering it for a year but you can add a spring push switch into the plastic and make it look like it belongs there. BANG ALL DONE
@SnapsFNN2 жыл бұрын
Thank you so much man!
@ryancole1304 Жыл бұрын
I put a new ignition in my blazer and the key turned for about a day or two and now it won't turn idk what the problem is but I need help figuring it out this isn't my problem
@ROCKO6335 жыл бұрын
God amighty and the steering column is already off? How does it come off before i bust it off
@amandagrier63604 жыл бұрын
Any way to start it without taking the entire interior apart?
@stevekrahn97073 жыл бұрын
Yes. Hole in bottom of column shroud is specifically there for poking the release button without disassembling the whole column, etc.
@jomoral175 жыл бұрын
Look out buddy ol' pal....could this actuator be the cause for all my accessories to malfunction or not turn on at all?....please help I done installed a new ignition switch behind the switch no key tumbler...please help
@user-up7ep7ds5p3 жыл бұрын
Check your wiring from the PCM to the Engine fuse box, the plastic circles holding the wiring harness in place and the actually plastic sheathing rubbing against each other can wear the insulator off one of the wires for communications. Now there's allot of diag to get to that point but there's a channel called "South main auto" Eric O is the one of the best Technicans I have seen on here. He doesn't preach the expensive perfect world remedy to your said issue. Just the proper way to fix it with simplicity in mind. Anyhow I randomly started having ignition problems, ended up burning out my starter. But I watched his video on explaining the wiring for the ignition signal and the Envoy he was working on had the same trouble codes and running condition mine did. Watched the video and took a educated guess on the wiring, pulled back the sheathing and sure enough the Ground for the signal wire for the ignition was about 75% worn through, actually heated the wire and had to cut a good bit out. Just took a butt connector, Fluid film and electrical tape and the thing has been running fantastic.
@renerosados.89855 жыл бұрын
Lifesaver thanks buddy
@RingZero6 жыл бұрын
What was the fix?
@Rickxx881 Жыл бұрын
It's not a fix. It's better just to replace the switch
@EZ4U2Say113 жыл бұрын
Dead battery makes the key get stuck too
@kevinleslie29922 жыл бұрын
What's a inline 6 4 cylinder
@darcithurston65385 жыл бұрын
I cut a hole in my colume under for that little button. Been this way for almost 2 yrs. Because i also had to figure out myself what this issue was.
@stevekrahn97073 жыл бұрын
Theres already a hole there from the factory for this specific reason.
@darcithurston65383 жыл бұрын
@@stevekrahn9707 not all are already cut out. The precut design is there but not cut out. I cut mine out.
@coreypipas32217 ай бұрын
@@darcithurston6538 what ended up being the problem? I have to use that little button to get my key out as well?
@lifechanges4097 Жыл бұрын
Thanks 👍
@maxstreim46124 жыл бұрын
Jesus fuck i feel so stupid of course i find out about this god button months later
@ud5066 Жыл бұрын
Mine turns just won’t go all down so I get the key out
@loudboysdotcom27153 жыл бұрын
Iv been fitting this thing for forever Iv undone my battery so manny times that my negative won’t get tight no more lol
@irish2u3894 жыл бұрын
Common people if your gonna share with people fixits, post a How too video or link to solve problems, Show you work , Tnks
@MarvinRWard5 жыл бұрын
Thanks man!
@Mick3y4147 жыл бұрын
Curious also
@shawnwithee63363 жыл бұрын
You looked on line and there wasn't any videos on how to fix the problem? BS! There's 20 videos
@juans66396 жыл бұрын
In the future, can you PLEASE film your videos in LANDSCAPE MODE, like our human vision is designed? Thanks.
@bam44446 жыл бұрын
I apologize I couldn't find anything helpful online and just diagnosed it and posted it. I did everything on my phone since my laptop was down. Will do better next time thank you