Like and Subscribe! Owen and I tackle the replacement of the front brake pads and hardware on his 2007 Jeep Grand Cherokee Laredo. This process is the same for 2005-2010 Grand Cherokees. music: bensound.com
Пікірлер: 27
@TheCristianSwag3 жыл бұрын
this vid was on my recommended after i asked you about changing my own brakes, google always listening
@dieselpackgarage87963 жыл бұрын
I like that Google is helping me out ;p
@joshuamoore24_75 ай бұрын
I put brake caliper grease on the channels the pads slide in, caloper bolts, and the fronts of the brake pistons. Then once assembled before the wheel goes back i hit the rotor up with some Bake cleaner.
@dieselpackgarage87965 ай бұрын
That makes sense to me haha
@Qchiko6 ай бұрын
Great video! Thank you not sure about using impact driver to tighten these type of screws due to possible over torquing and possibly breaking bolt 😮
@dieselpackgarage87966 ай бұрын
That is a very good point!!
@highlightzilla9581 Жыл бұрын
I pop them off use c clamp and makes it alot easier and faster the flat head screw driver is a waste of time but everyone does it different great video bro appreciate it buddy
@dieselpackgarage8796 Жыл бұрын
That's for the idea. I'll definitely try that!
@LydiaJonz2 жыл бұрын
Great video a bit of advice you can use a c clamp to help push the pistons back by placing a old pad on them both just so you don't have to do them one by one then use the clamp to push that brake fluid back up in the lines
@dieselpackgarage87962 жыл бұрын
This is a good idea. I just believe I didn't have a good c clamp available during this time. I'll try to show this next time!
@LydiaJonz2 жыл бұрын
Also taking the brake fluid cap off before ping the pistons helps with bleeding the brake lines
@eyespy30012 жыл бұрын
God video. One piece of advice: an impact is good for breaking and loosening bolts, but you can over-torque when tightening. Always best to hand-tighten, just to the point they’re nice and snug.
@dieselpackgarage87962 жыл бұрын
That is true. It can certainly lead to issues in the future, but just my quick and easy way since I'm accustomed to my impact. I'll make sure to point that out in future videos. Thank you!
@g.h.87882 жыл бұрын
Ay fellas good work! Thanks for the help! Keep doing your thing!!!!
@dieselpackgarage87962 жыл бұрын
I'm glad it was helpful! Thank you for the encouragement!!
@mitchcornacchia968 Жыл бұрын
Good job boyz!
@dieselpackgarage8796 Жыл бұрын
Thank you!!
@countryside81223 жыл бұрын
You should also grease where the pads slide against the pad. so the pads slide and do not hang up. You can also add a little silicone on the piston rubber to help keep it pliable. great and helpful video.
@dieselpackgarage87963 жыл бұрын
Ah, I will keep those in mind, they sound like good ideas! I'm glad you found it helpful!
@APD6046 ай бұрын
It's easier when you have a Disc Brake Piston Compressor vs trying to compress the piston with your hand on the brake pad.
@dieselpackgarage87966 ай бұрын
Heavily agree, I'll have to get that tool!
@petemilano96972 жыл бұрын
You need sil Glyde on that hardware so the pads slide easier and rubber boots my guy ... no impact gun tightening bolts ... open brake fluid cap ... c clamp to push in piston.. brake cleaner ...
@dieselpackgarage87962 жыл бұрын
I wasn't thinking about putting the grease on the slide hardware when I did it elsewhere, but that would have been a good call. Where are you recommending rubber boots? Impact was me cutting corners, with low settings, but I also recognize that this can cause issues in some cases. I unfortunately had my C clamps at another location, but opening the brake fluid cap would have been a good move to make it easier and put less stress on the system (although I doubt I nearly met the operating pressure these are routinely under). I do appreciate the input and it definitely gave me some stuff to keep in mind going forward. Thank you for taking the time to give me some input on how I can improve on future endeavors!
@farisalmemar2738 Жыл бұрын
How to replace center console lights
@dieselpackgarage8796 Жыл бұрын
Honestly have not had to do that on this car yet haha.
@missywood97683 жыл бұрын
Should bleed them and tip... c clamp on old pad works mo betta to retract calipers j/s..
@dieselpackgarage87963 жыл бұрын
C clamps would have certainly made compressing the calipers easier. But I didn't have my clamps pulled out at the time, and the calipers didn't put up too much of a fight 😂 And I could have bled them to make it a little easier, but the fluid in the system was relatively new, so I didn't want to needlessly replace and make it messier.