Level your jeep with this How to Video!!!! Drop a comment below if you have any questions and dont forget to like, SUBSCRIBE and share with your frineds!!!!
Пікірлер: 56
@shawn162510 ай бұрын
Just did this job... My suggestion is to not reuse the locking nuts that are used in the upper control arm and tie rod. My other suggestion is to make sure you have a ball joint separator because you can only beat on your car so much before you accidently break things. If I would have had these things available it would have been much easier.
@mkedan67413 жыл бұрын
I have a 19 JGC and have this kit which I plan to do this spring. The locktite is a good idea but I would also remove the rotor(it's held on by a o-ring). The insructions show removing the knuckle. Every video I have seen of this is different but yours is helpfull. Thanks.
@BSBASSIN3 жыл бұрын
I do these on a weekly basis what I say will work trust me.
@mkedan67413 жыл бұрын
@@BSBASSIN I just pulled the wheel off and what I thought was plating is aluminium. The 2019's have a alloy lower control arm and knuckle. No hammering! I have to figure out how to get the tierod and upper balljoint out without damage. Mine is a Hemi powered Limited with the tow package/Nivomat shocks, the ass end is exactly 2 inches higher than the front (measured @ wheelwells) and I want it leveled. Thanks again for the video and any advice is always greatly appreciated.
@scotianbank9 ай бұрын
Awesome guide!! I hate to be a nuisance, but could you write up a list of all tools you'll need (maybe a "must-haves" list, and a "nice-to-haves" list?) to install this kit? Thanks!!!
@Izzydominguez223 жыл бұрын
Keep up the good work my friend. This video put all the other install videos to shame. You are appreciated.
@BSBASSIN3 жыл бұрын
Thank you sir! I try to do my best to help others
@johngaringalao91432 жыл бұрын
Thank you for this very detailed video!
@adamkingersoll51854 ай бұрын
Excellent video. I did this on my 2017 dodge durango gt. This kicked my butt. I had to take the sway bar off because it was interfering with the tie rods. Any ideas what I can do for a sway bar?
@sheerwillsurvival20642 жыл бұрын
Everything rust in the rust belt not much rust on my Jeep’s in Texas 😁
@cmorgan09093 жыл бұрын
Great work man. If you don’t mind me asking, what did you charge to do this? I’m considering DIY versus paying a shop. Or, any shot you’re in Chicago area? I’d gladly go to you
@BSBASSIN3 жыл бұрын
I am in Chicago. Find me on fb Brian Risley and send me a PM. It's a picture of me holding up a fish.
@BSBASSIN3 жыл бұрын
Or tell me how I can get in touch with you.
@loboa27472 жыл бұрын
Brother I’m in Chicago as well struts on their way from florida, can we some how talk to see how much you you’ll charge me to do both
@durteeduce3849 Жыл бұрын
Im currently looking for a shop or someone to take my Jeep too in chicago as well if yall have any recommendations!
@CombatLazza3 жыл бұрын
Great video, thank you mate
@s2knott3 жыл бұрын
excellent video!
@adamt4742 Жыл бұрын
would this be similar or pretty much the same as a '12 Durango?
@BSBASSIN Жыл бұрын
Probably the jeep and dodge are the same platform. I have not done a Durango recent enough to remember though.
@jackstracks47943 жыл бұрын
Thanks for the detailed video. I'm thinking of doing this on my 2020 JGC. I was told that I would have to do a front wheel alignment after the install, do you agree?
@BSBASSIN3 жыл бұрын
Yes
@hellkitty10143 жыл бұрын
HIGHLY recommend an alignment with so many components removed.
@camaroboi133 жыл бұрын
Nothing like pulling everything apart only to find that on 2017 the strut bolt is well over 1” and I don’t have that size
@michaelhorn45402 жыл бұрын
Im ordering a RC 2.5 inch lift kit for my 2011 grand next week
@BSBASSIN2 жыл бұрын
Awesome you will love it
@alejandroandrade20162 жыл бұрын
Muchas gracias por tus detalles 👌
@matthewskowronek41163 жыл бұрын
Would have been nice to see the final outcome
@BSBASSIN3 жыл бұрын
Search bs bassin on Facebook and message me I'll get you phoots
@camaroboi133 жыл бұрын
@@BSBASSIN I don’t have social media
@alanalvarez4002 жыл бұрын
I have a 2013 grand cherokee I put the leveling kit rc 2.5 in front but my shock absorbers have already decomposed, DO you think that i need to buy longer ones or with the originals it should me ok.?
@BSBASSIN2 жыл бұрын
Just buy quality ones. Shocks are rated for 50k miles
@maazmohammed90213 жыл бұрын
Hlo,can I put this lift on 2011 jeep grand cherokee laredo???
@loboa27472 жыл бұрын
I have someone else installed the leveling kit for me so now I want to replace the struts, do I have to do the trimming of the bolts like you did? Thank you in advance
@BSBASSIN2 жыл бұрын
Not sure if it's installed everything should go in and out easily
@nissanquest20022 жыл бұрын
Are the motor mounts accessible when replacing both struts ? Thank you .
@BSBASSIN2 жыл бұрын
I don't remember
@ballsbuster123 жыл бұрын
does the jeep your working have air suspension or regular coils suspensions?
@MonkeyDLuffy-cm9bc3 жыл бұрын
You can't lift the jeeps with air suspension only coils
@ThatRacingBanana11 ай бұрын
Im converting mine from air suspension to a strutmaster coilover system with the rough country lift kit
@carnage62883 жыл бұрын
I put on the RC 2.5" kit on my 2018 GC w/stock 18" wheels. Do you happen to remember what his tire size was he put on? Looks like he has 20" wheels. Thx
@BSBASSIN3 жыл бұрын
I actually do not I know they barely fit when it was stock
@hellkitty10143 жыл бұрын
You could get away with 285/60s. Anything wider or taller and you will have to trim/push the pinch weld back.
@outdoorreelz31812 жыл бұрын
Did you cut the bolts so you didn’t have to compress the springs?
@BSBASSIN2 жыл бұрын
Not the bolts have to be cut because they are too long for the spacer that mounts on top of them.
@outdoorreelz31812 жыл бұрын
@@BSBASSIN ok. Everyone else I’ve watched as had to compress the springs to get the spacer in. Did you do that? Thanks
@bobelkiniii14613 ай бұрын
Why pull the CV
@allstarfailure68483 жыл бұрын
so do you have to have it realigned after this?
@BSBASSIN3 жыл бұрын
Yes
@lucystephenson137110 ай бұрын
Whomp whomp
@ballsbuster123 жыл бұрын
where are you located can i bring my truck to you ???
@BSBASSIN3 жыл бұрын
Chicago area. Find me on Facebook Brian Risley
@wilder211 Жыл бұрын
I thought compression of the springs was required?
@BSBASSIN Жыл бұрын
Not with this kiy
@wilder211 Жыл бұрын
So you do not have to remove the lower ball joint nut? The instructions says to remove.
@BSBASSIN Жыл бұрын
@98th Meridian please watch video everything is in the video. I install leveling kits o. So many different suv, trucks, and even subaru cars I cannot remember everything from every one