2013 Ford F150 5.0 Long Crank No Start

#Ford #F150 #LongCrank #NoStart #CrankPositionSensor #FuelPumpModule #FuelPump #Mechanic #Truck

[@treyfetterhoff7847]

This was a life saver. Thanks brotha!

[@jefedelacordeon]

Thank you so much! I had tried the 27 fuse and nothing saw your video at 9pm went outside and hit the module few times and bam turned on!

[@bullsmechanictv5060]

Glad my video Helped !!!

[@metalbender485]

Same thing happened this morn. It happened one other time and the fuse was blown. This time the module. Thanks for the info.

[@bullsmechanictv5060]

Glad it Helped!!

[@moosenmobile31]

Tapped on mine. Fired right up! Ty!!!😊

[@moosenmobile31]

Eh, was too happy too soon. Died again, replaced fuel relay and still happening. Going to ford today or tomorrow

[@ITzMonMotorSports]

lol 2am just disconnect it and connect back it work

[@bullsmechanictv5060]

Glad to hear brother !!!

[@mountainmike1685]

So was the fuel pump running before you put that part on, I have a long crank no start but I can hear the fuel pump running but not sure what is going on

[@ivancostilla3074]

I have a ford f 150 -2009 and has the same problem. i went to auto zone to buy a new module i already installed but still have the same problem.

[@bullsmechanictv5060]

Any codes ?

[@wyattrodriguez49]

do you think it would be the same as mine, mine is a long crank and then it will start but, when i start it then turn it off and try to start it again it will just crank no start

[@ramirocisneros9963]

Check the fuse 27

[@bullsmechanictv5060]

What was it ? Sorry for late response

[@richardgrimes6208]

Do you have a way to test the fuel pump driver module? Also do you have a link or part number for it?

[@bullsmechanictv5060]

FD1026 is the part number an tbh not sure but if you have same symptoms without codes more likely you got same problem goin on ! I used a scanner an noticed on data that the module was engaging only for seconds an turn off pump when I cranked it ! Hope it helps !!

[@richardgrimes6208]

@@bullsmechanictv5060 thank you! I bought a driver module from AutoZone, it worked for about 15 minute's then started blowing fuses. Three different ones without turning over. I bought a relocation kit and driver module from Ford (cheaper than just the module from AutoZone) put them both in and so far so good. I've only driven the truck a handful of times since doing it this afternoon but it hasn't even shuddered.

[@coopergt500twin5]

Check pressure from fuel rail !

[@jamesarwood2207]

Ty so much it worked I changed everything pump fuses etc was at a lose till I seen u video it worked 77.00 fix after all that again ty

[@bullsmechanictv5060]

Glad I could helped thanks for the comment 🤘🏽

[@trigam41]

After all that "Blair Witch" camera work, you didn't even show how to remove the module! It was out of frame! This doesn't help at all.

[@bullsmechanictv5060]

Glad I couldn’t help ya

[@moosenmobile31]

2 10mm bolts attaching it to the rail. Once you get those out, flat blade screwdriver in where tab is and should be able to shimmy the connector apart.

[@andrewpowers5823]

Imagine not being able to figure it out 🙈👌

[@benjurmind1318]

Jumped the gun and replaced the fuel pump driver module. My Fuse 27 was burnt on one of the contacts. Replaced that and it started up after a try. Thank you!

[@bullsmechanictv5060]

Glad I could help !!!

[@tangoblast4751]

Same here 2010 XLT 4.6 check fuse 27 is good my has power but cranks for a long time so would i Be able to test to make sure it's that how did you figure it out do you disconnect the battery when you unplug that part you took off

[@bullsmechanictv5060]

I didn’t disconnect the battery an I noticed the fuel pump wasn’t making any noise when turning switch on an had long crack as if I didn’t had fuel ! An I had just replaced the cranks position sensor since the truck had a code on it so I knew I had sparks . So I replaced module I doubt a pump would go bad for a 2013.

[@tangoblast4751]

@@bullsmechanictv5060 so it's the module how much was it and can you do it are your own or need a mechanic

[@zuti28]

How do u unplug the sensor plug u just pulled on it or u have to squeeze it

[@bullsmechanictv5060]

Sorry late response but pretty sure got to squeeze to release the plug

[@cristhoferpalacios8111]

Lo máximo!!! Tengo el mismo problema con mi F-150 5.0 2011, probare en estos días mientras llega el repuesto y te aviso!

[@bullsmechanictv5060]

Que paso?

[@cristhoferpalacios8111]

@@bullsmechanictv5060 es que cambié la mariposa de aceleración, selenoides, arbola de levas, todo Nuevo pero no suelta los cambios como si se quedara en cambio 3