2013 Nissan Rouge Clock Spring Replacement / Father And Son Rebuilds

[@mrlegoblox448]

Your video saved me about 300 bux, lol. I think it took me 40 min to do the whole job. When I unplugged the wiper arm though from the clockspring, I didnt need to unplug the cable. It was long enough to just lay the wiper arm across the display shelf behind the wheel while I worked. One note, the steering wheel position sensor attached to the back of the clockspring had to be moved to the new clockspring I bought direct from Nissan. I think someone may have replaced it before as there are 2 tabs on sensor housing that center the sensor to the clockspring. one's wide and one's narrow and they fit into keyholes on the clockspring. When I took my old one off I noticed that these tabs were not in their slots.

[@gettended]

Literally just finished fixing my horn. Haven’t had a horn in five months. ❤

[@sergioramirez4511]

This video saved me $800 by doing this myself. I bought the part online for $100 and purchased a Trox socket set on Amazon for $15, since I could not find these anywhere, but online. I have the normal Trox set for my daughter's Jetta. The Nissan dealership wanted $1000 for the full job, and it only took me about 45 minutes. The hardest part is putting the plastic cover back on and lining it up. I wish you did not jump the camera around. It was hard to see how to take off the clips, which really just requires that you push in the tabs, but still a great video and thank you for sharing. I normally look for online videos and based on what I need to bu as far as tools go, to do the work myself, before considering a shop.

[@seangillum1656]

I cannot thank you enough for making this video. It is so concise, clear, and informative. My wife has the same make and model and I just replaced the clock spring because her horn didn't work. This video saved us hundreds of dollars in labor and diagnostic fees. I'm a carpenter by trade but not much of a mechanic. Thank you again, I really appreciate it.

[@jahraflorentino3126]

Thank you so much for making this video!! My horn and all my buttons work now. You made this very simple and not boring at all. Lol!

[@roadpar]

Thank you for this video. Saved me a couple of hundred dollars. I just changed mine today. Nissan Rogue 2011. You should put in the description the tools used: Torx TR30 3/4 or 19mm Spark Plug Socket

[@TortureBot]

Did you end up having to recalibrate your steering angle sensor (the part he almost forgot that attaches to the back of the clock spring) after you replaced the clock spring? I'm about to do the clock spring on my wife's 2011 Rogue.

[@roadpar]

@@TortureBot I used the same piece from the old Clock Spring. You have to be careful, it fits only one way. It has like a guide built in the plastic. I don’t really remember very well, but I remember I almost installed it the wrong way (the back plastic piece). O the other hand, I don’t know what recalibration you are referring to.

[@TortureBot]

@rodrigopacheco833 this link shows a pro mechanic replacing the sensor and says he'll have to recalibrate it. At the end, he shows the short process done with a scan tool while he drives around the block. Thank you. kzbin.info/www/bejne/onrGaqqJfLVklbc

[@jlabproductions1004]

Great step by step breakdown for someone “just winging it”! Couldn’t even tell this was your first rodeo. Very helpful especially the part about the caution warnings, I never knew that’s what you’re supposed to do with them lol And the person recording was very good at getting all the angles so we could see everything you did. keep up the quality work and entertainment guys!

[@superautocreations6148]

Thanks glad you enjoyed the show. We are going to keep it going and see where it takes us you are welcome to come along for the ride.

[@thecrowsplace1134]

Great video..helped me out a lot!! VERY VERY IMPORTANT ADD ON HERE... the black round thing you took off the old and put on the new is called steering wheel position sensor.... it's very important to line the two tabs with clock spring slots otherwise your traction control light will come off and on and car performance drops!! Found out the hard way wasting 7 hrs looking for issue!

[@superautocreations6148]

Glad we could help Sub us we are coming back with more great videos.

[@olvinorellana]

I need help with traction light. It comes on 😞

[@spade304]

Hey can you help me with this?

[@thecrowsplace1134]

@@spade304 ?? Help with what?

[@Silenceplz595]

I have the same issue with TC light came on after charging the clockspring. Can you explain what two tabs I have to line up?. Thank you

[@sean-thomasrussavage9539]

Gonna use this and thank you.

[@arif29khan]

turn the bloody music off!

[@irsty54]

2008 Nissan Rogue, horn not working when pressing steering column. Pulled horn and tested it works. New Relay and 10 AMP fuse. No horn working. Next step is to inspect steering column. Will this fix my horn issue?

[@Raul-wt5jx]

YOU ARE A LIVE SAVER!!!! My wife's Nissan Horn stopped working. It only works when I turn the wheel to the left. Does this mean I have to replace the Clock Spring as well????

[@bruceelwell4264]

Informative video, just can't stand the music. Sooo agrivating.

[@gettended]

Thank you

[@johanahernandez1853]

I didnt' see you take off the plastic thing you said to wait until the end? did you end up leaving it on or did you take it off ?

[@cliftonsmith5451]

Great video my wife has a 2010 rogue her horn doesn't work along with the airbag light on i was told its the clock spring?

[@RD-xl6ne]

I got the same problem with my girls car

[@amandawhite8562]

do you know what size the tamper proof torque was that you used? i’ll have to buy it and i’m not sure what size to get

[@richdiscoveries]

I work for Chevrolet / Mazda. In my 20 some odd years I've never had to pull a wheel on a Nissan yet. But I got to do it for a friend tomorrow. Clock spring, I guess that's a common problem on these? At least I'm thinking clock spring, horn, driver airbag and cruise control code, and all three of those things go through the clock spring. I was going to run to my shop real quick and grab my steering wheel puller but I wanted to see what bolts threaded into the steering wheel with the puller, but your wheel just slid right off without a puller? Again never worked on nissan, I've always had to use the pullers to get them off. I'm still going to go grab it but did yours really come off like that? There wasn't any loosening in between scenes? And regardless, was it threaded or did it have the bolt with the foot that you put in to pull it off if it's needed.. Just wondering, like I said I'm going to grab some tools anyways but I think I only have the bolts not the pieces with the foot. Those were GM specific I believe? And those are in the back somewhere. Also that airbag being held in with Torx is absolutely beautiful. GM has these stupid metal spring clips and you got a fish around the back of the wheel with a pocket screwdriver to release the damn things. Either way awesome video, thank you.

[@marckvaler3726]

NISSAN ROGUE 2010 SL the same steps. Great video. Help me a lot. I save 300 in labor. The part cost me 375. Thank you

[@rodrigocasanova5830]

What’s the number part? I have the same Nissan Rogue 2010

[@Royosankar]

Great video! Did the Airbag light come back on after you changed the clock spring? I have the same issue with my 2013 frontier...

[@Notsomysteriouguitar]

Saved me some money on my 2010 rouge.

[@falcon3s872]

Great video. Just about to replace clockspring in 2010 Rogue and without your video that would be a challenge...

[@Jamila255]

Hey I’m doing it on a 2010 as well any difference you found from this video?

[@johnwinchester2428]

Alot of help to my change out! Thanks!!!

[@russodfedny]

I have a 2008 Nissan rouge I have same problem, now I know what to do Thank You, also one my problems is front seat passage weight sensor.

[@superautocreations6148]

Sounds like the senors might be bad, not sure about that. Good Luck!

[@8o4h10essohess6]

What size torque did you use?

[@nancyseeley2041]

My clock works, but when I start it up again the clock displays a different time (like hours different). I reset it and when car is started up again....same problem. Any hints/ideas?

[@danielreyes8665]

Great video! How many times did you turn on and off your vehicle so the airbag light go out?

[@superautocreations6148]

I did it 3 times to get it to reset the air bag light.

[@sergioramirez4511]

Cycle the key 3 times. Turn on and when the airbag light turns on, turn off the key and count to 8 and do this 3 times. On the fourth try, the light will stay solid and then turn off. Do not turn on the vehicle, just cycle the key. There are some youtube videos on how to do this.

[@waelyassin7348]

Thanks for the video.. i do have 2008 Nissan Rogue SL I did all steps like you did exactly but after i did drive test, the ABS Light and the VDC and slippery road light all come on the Dashboard and the car during the drive it’s ABS brakes try to stop the car ... idk what to do .. have you get same issue?? Plz let me know... thanks.

[@superautocreations6148]

No i resolved my issue not sure why you are still having the problem yours is also older then mine. Just don't give up you can fix it.

[@waelyassin7348]

i did fix it last time,, by disconnecting the battery for 60 seconds and attaching the positive and negative together after that everything was good to go.... thanks for get back to me 😉.

[@Laboricuamamys2002]

Having the same issue . Please help

[@xdynamo7523]

If my fuses are good an rely . Horn sounds when I hit the alarm so I know it’s good . Just the steering wheel doesn’t honk anymore . So I have to replace clock spring ?

[@jbs-vu5mc]

Thanks for the video!!

[@joshuagonzalez2415]

Does your horn work before the replacement?

[@erikduman9790]

good job

[@oscarhernanhurtadohurtado7852]

HI hello what was the initial problem Did the steering wheel controls and autopilot work before replacing ???

[@superautocreations6148]

My problem was the air bag light was on because the clock spring went bad. Hope that helps you.

[@tgee8216]

@@superautocreations6148 where did u purchase the clock spring

[@luismedina8502]

Great video. But don't make the mistake of buying it on line from the big seller, I ended up having to buy the original one at the dealer after my wife's car was all apart and lost my money with the imported third party seller, substandard part from the internet big seller....junk!

[@easydiyhomeimprovements4942]

Would this procedure be the same for a 2011? Where did you get the clock spring from? My wife’s car horn will go off constantly if the steering wheel is straight, air bag light is on, none of the steering wheel buttons work and the volume on the radio constantly goes down and you can only turn the volume back up when turning the steering wheel back and forth, are these accurate symptoms of a bad clock spring?

[@gymbrowski8090]

Your cruise control is also acting up I bet. Yep sounds like the clock spring. Mine too.

[@roadpar]

I had exactly the same problem. Bought it on eBay for $100 last week. There were multiple cheap ones around $30 but I decided to go with the one with best rating for $100 bucks.

[@DavidGutierrez-zi4dy]

great!!

[@Phantasmos]

Where did you Order from? DO you have the part number?

[@spade304]

If your anti-skid sensors turn on you probably didn’t line up the two white plastic tabs behind the sensor make sure they are lined up when you switch it from the old one.

[@joonyaboy]

Thanks. I will try this again

[@GFS695]

I think I made this mistake, thanks, will check this out, I was thinking this, my slip sensors are kicking in when I make a right turn, pretty dangerous as it kicks on brakes automatically.

[@leonardoreyes2741]

Thanks for the video I could already do it on my 09 Nissan Rogue but after wanting to drive the anti-skid sensors and the VDC are activated. Could you help me with that?

[@superautocreations6148]

I can try to look into your issue hit me up if you have not fixed it.

[@Laboricuamamys2002]

Same thing happened to my car

[@Laboricuamamys2002]

SuperAutoCreations did u find out what was wrong? My car turned on the same lights after changing the clockspring

[@superautocreations6148]

@@Laboricuamamys2002 Did you put a code reader on it and find out the code you are throwing. That's where I would start. Need to know the code and do some research on it. Good Luck Bud. Let us know.

[@spade304]

Hey did you get the issue fixed?

[@grupovalhalla6873]

Disculpe que numero es el dado para quitar la bolsade aire

[@RD-xl6ne]

How much did you pay for the clock spring at the dealership?

[@rockerpat1085]

So you can't get your state Inspection with the Air Bag light on? Not a requirement here in Texas!!! Air Bag, and ABS lights don't count in Texas!!! Keep Rocking it out Guy's!!!

[@superautocreations6148]

Yeah here in MA. they make sure you have no lights on at all it sucks. We just go with the flow.

[@aminatajaiteh2201]

hi, how do I know if a clock spring will fit my car? i have the same car as you and I'm having trouble finding a part

[@vpaztk]

Same here, having problems finding the part. Help! Where do I order?

[@roadpar]

eBay. Check compatibility with your car year and model

[@zhongwenrui]

Turn off the background music. Very disruptive

[@Silenceplz595]

Do you remember what size is the two tamper proof torque screw.

[@roadpar]

T30

[@alexcanaca2477]

What size is the temper probe tool..I need to buy one..

[@GTRaZoR22]

Alex Canaca do you mean the tamper proof security torx bit.? The one he used to take out the airbag?

[@superautocreations6148]

Not sure what size i used but i have a set i bought from Matco Tools

[@caseyroot6957]

I know it may be too late to be helpful for you but for future viewers with the same question its a T30 tamper proof for the side bolts

[@raffi_abualraf]

Great video thank you. Do you remember size of the steering wheel bolt bit?

[@spade304]

3/4

[@joonyaboy]

Mine was 19mm

[@quinterod1000]

Do you have the parts number

[@leevww]

Music isnt necessary .shame could have been very good..but 5 mins is enough

[@ACD2B]

Thank you for the video, however I could do without the munchkin dance music! Kind of distracting! 😅

[@brainfreeze9653]

The music is a bad nightmare and a total distraction.

[@aezah89]

This is not a clear video

[@arif29khan]

I can't hear a word you are saying!!!

[@GGGF-l7g]

יריב עם שם לי בתגובות עם מיקה