[2013+] RAM Promaster - Scout Front Bumper Installation

[@lassepalmberg8130]

Very interesting to watching you work😀👍👍

[@jamesmcneal7228]

What about the front bumper sensors ?

[@tower992]

Anyone wondering if this will fit on a 2022 promaster 3500 with the 9 speed trans it does . I have a solis 59px. Use it for snowmobiling and pulling wave runners out of the water so now I have a peace of mind knowing I can get myself out of a jam. I did not have the cooling lines that had to be moved. So that part was easier but I did cut the bottom bumper shroud support off the oem bumper and re used it to support all the lower plastics. I got a 12000 lbs traveler winch. Moved control box up out of the way.

[@rainwu7007]

I have a Roadtrek same chassis year with you, but it has under hood generator which I’m not sure if it can fit in this bumper 😅

[@lkazanov]

Very nice, there seems to be a slit between the new bumper and the front facia on either side. Is there any whistling or wind noise going down the road?

[@BackwoodsAdventureMods]

None that we have noticed or heard from customers.

[@dannyhightower1]

This looks great and ready to buy one. What is the suggested load rating for the winch mount?

[@BackwoodsAdventureMods]

Thanks! We can't suggest an official load rating because of the rigorous amount of testing and certification we would have to do, however we have seen customers support things like e bikes or small motorcycles. Hope that helps.

[@marketingwithomg]

This is a great design! Can this also work with bull/brush guards designed to fit the promaster?

[@BackwoodsAdventureMods]

Thank you! We apologize for the delay. We have not verified that it will fit, but it does have adequate clearance. You may need to get crafty with the mounting.

[@chillywilly3397]

Be careful you don't overheat your engine. Your lights block airflow through the radiator.

[@BackwoodsAdventureMods]

Appreciate the tip! We've tested this van and driven it 12+ hours ourselves with no issues. In the Colorado mountains as well. We have built in large airflow/winch access holes in the bumper itself, and so far, the lights haven't affected any temperatures.

[@CanadianTexaninLiguria]

@@BackwoodsAdventureMods In Florida or Texas, you have serious cooling issues. Be aware the Promaster temp gauge is a happy gauge - its not even close to being accurate.

[@BackwoodsAdventureMods]

@@CanadianTexaninLiguria Good to know, appreciate the info.

[@blueracer66]

I like that van wrap. Where can I get the design? It gives me Husqvarna Norden 901 vibes.

[@rainwu7007]

Do you know if this will work with Roadtrek Zion which had under-hood generator?

[@jtcommunication]

That looks amazing!

[@BackwoodsAdventureMods]

Thanks!

[@irokdempurpz]

what about the front license plate? aren't those required in Colorado?

[@BackwoodsAdventureMods]

You can purchase a fairlead license plate bracket that most people use. It flips up and down over the winch using the fairlead bolts.

[@connieseale1224]

Do you have a video on wiring the winch ?

[@BackwoodsAdventureMods]

We do not since there are many different ways to do so depending on your particular winch and set up.

[@SoCalSurfer69]

I don’t understand why on a pro master. It’s not 4x4 or really have clearance for off-road other than fire roads.

[@melrichardson2392]

I would like to see possible potential pictures what these vans could look like and be used for ,have seen t 4 s and unlimited parts and go anywhere what about these vans are limited not very good etc.

[@BackwoodsAdventureMods]

Check out Last Line of Defense on KZbin. This was actually his van and he has done several vlogs and adventures with it.

[@brettbutler9730]

Looks good.

[@CanadianTexaninLiguria]

Bumper is sweet but those lights are obnoxious. A White light bar would have looked and performed so much better.

[@erikaamac2727]

Amber lights have a temperature of about 2500 to 4000 kelvins, a decent value for human eyesight. They are better than white fog lamps as they have a low refraction rate, and they have a more extended reach.

[@taurusview9]

Damn...that was nice!

[@joeep46]

Would the added weight cause the front end to sag a bit?

[@privatesector0422]

Of course not it's barely anything plus the suspension is built to handle this type of weight including much more before sagging...

[@dsandusky123]

why is jeep bumper that is way bigger and more cost less than half metal center bumper.. vanlife price gouging is real

[@BackwoodsAdventureMods]

Most Jeep bumpers are very cheaply made and very easy to fabricate.

[@SunDevilinFL]

Yeah because the front end of my promaster isn’t heavy enough 😂