2014 Mitsubishi Outlander Rear Hub Bearing /Speed Sensor Replacement

[@richardhume2811]

I am in the UK and my clip had rusted off. Getting the bolts out for the hub and getting the hub out was a horrible job as everything was rusted up. I wish I lived in a warmer country with less rain and no salt on the roads. I found reaching in for the clip from above was the best bet. Thanks for the video.

[@kgautorepair3335]

Thanks for reaching out,Richard I’m glad you find what you were looking for,please support our KZbin channel,by subscribing and like the video also,it helps our channel 👍🙏

[@stevemorgan5256]

Good look! Christ I must have googled this 1,000 x's to show exactly this! Finally Thank you!!!

[@xsbaggage2666]

Hey KG, I’m in the UK and this vid really helped me discover a fault on my rear sensor. Much obliged and thanks for putting it online. 👍👏

[@kgautorepair3335]

Thanks for reaching out,please support me,by subscribing 🙏

[@TheRebelOne.]

Excellent video. I didn't realise the sensor went inside the car. Now I know as I have to replace this assembly tomorrow.

[@kgautorepair3335]

Sure please support me by subscribing, I will appreciate that 🤙

[@ripmom7551]

Great video , my 2013 Mitsubishi outlander sport had all light on like a Xmas tree- abs,asc,esp,control, cruise,4x4, stability etc and those sensors cause all of it just fixed that

[@kgautorepair3335]

Thanks for reaching,please support me by subscribing to my KZbin channel,I will really appreciate that,i like the video also,it helps our channel 👍🙏

[@allwellbud]

Helpful video. Thank you KG!

[@kgautorepair3335]

Thanks for reaching out, please support our KZbin channel by subscribing, I will really appreciate that 👍🙏

[@hartwellscunthorpe3206]

Great video very helpful what size is the hub bolt please

[@kgautorepair3335]

Thanks for reaching out, I think it 34 socket, please support your boy, by subscribing, I will really appreciate that 👍🙏

[@caseysheehan8643]

Thank you In my 2006 outlander there is a little porthole in the interior but looks like I have to pull the whole cover off. Gosh I hate ABS

[@kgautorepair3335]

Thanks for reaching out, please support your boy by subscribing, I will really appreciate that 👌

[@marst060]

Great video. Just Discovered that my speed sensor had come loose. Unable to get i back. Just sits very very loose, so will come off again 100% sure. Looks like the mount/spring has been rusted off. Is there a fix to this other then changing the whole hub?

[@kgautorepair3335]

You could use JB weld plastic,but you can’t drive the car 🚗 for at least 12 hours,to allow it to dry properly, have you subscribed to my KZbin?

[@marst060]

Subscriber of course :) Where would i put the plastic weld? Just a tiny amount on each side?

[@kgautorepair3335]

Sure 👍

[@garethwatson5952]

Hi, cracking video, very helpful. Juat wondering did you use a genuine mitsubishi sensor or an aftermarket sensor?

[@kgautorepair3335]

Thanks for reaching out, yes I use genuine Mitsubishi parts, please support us by subscribing, I will really appreciate that 🙏👍

[@sem3945]

Thank u KG...keep it up bro!

[@kgautorepair3335]

Thanks 🙏 please support me by subscribing

[@user-hx1pd9nj9o]

Nice one bro

[@AndréTraversy-p4r]

Tanks

[@kgautorepair3335]

Thanks for reaching out, please support your boy, by subscribing, I will really appreciate that 👍🙏

[@markscheidlmeier6523]

Great job!

[@kgautorepair3335]

Thanks men I appreciate that, please support me by subscribing 🙏

[@AndreiPais]

Danke

[@ganeshnarayan5505]

Hello Gee very well explained you got a new sub.