2014 to 2020 Teryx and Teryx 4 800 catalytic converter removal

[@cookymudstar]

Thanks for vid I removed rear on my 16 first month I've heard of second one but never found real information to confirm what part of pipe thanks for posting

[@trialnterror]

Question, I have a 2014 teryx 4 , it started not wanting to idle and when you press the gas anything past 1/4 throttle it Boggs no power! I’ve put a new fuel pump assy NO CHANGE! Have you or anyone you know had and FIXED this issue?

[@brooke14100]

My 2015 was doing the same thing. Ended up being plugs! Two new plugs Ana she was good!

[@trialnterror]

@@brooke14100 that’s exactly what it was! Spark plug was fouled in the forward cylinder. As soon as I pulled it out it was still wet with fuel! I put 2 new plugs and it now idle’s and has power when I step on the gas! The only thing I still have is if I’m at idle and go to step in the pedal just barely there engine has just a little hesitation then takes off. I’ll have to figure out that issue. It’s not all the time just sometimes!

[@ryank4]

instead of cutting the pipe, could you come in from the the end and knock it out with a screwdriver/hammer? just curious. Thank you!

[@rightcoastoffroad]

No, unfortunately you can't

[@mrchicken8170]

Access to everything on the T4 is a pain. Even the belt. The whole 9 yards (2:59), is a full exhaust system. Big gun evo dual pipe with a big gun fuel programmer. Big gun makes a great set up for the Teryx 4. Good vid.

[@rightcoastoffroad]

Thanks!

[@christopherlafko2389]

Good video. I’m wanting to remove my converters from my 2020 Teryx4. Question. Would it be better / easier to remove the skid plates or center console / floor boards to remove the exhaust pipe from the engine. Thanks in advance.

[@rightcoastoffroad]

On a t4 I would remove the rear floorboard, center console and the Skid plate to get to everything

[@wildroundhere5456]

@@rightcoastoffroad I have everything unbolted but can’t fit the header pipe out the back or the bottom. Should I remove rear floor board to get it out?

[@rightcoastoffroad]

@@wildroundhere5456 yes

[@waynejenkins1038]

I used a hole saw on the rear cat two minutes it was gone. Front did like you did. I went one step further and cut the small tube in the muffler out left the baffle plates in.even more throttle response and power feels great. I have a 17. T2 thanks

[@terrancesmith1674]

I wish you would have recorded the sound after they are out.

[@ianmc6063]

THANK YOU!!! I did not know it had two converters, good thing I watched your vid. Ended up wrapping my exhaust while I was at it.

[@williampoole5143]

I don’t need a tuner if I delete both cats on my 18 Teryx4?

[@brianmeyer6549]

Did my today the worst part is taking everything apart not a big issue removing the cats

[@brianhessling6987]

Most informative video on this subject. Thanks for this

[@rightcoastoffroad]

Thanks!

[@MisterMcCabe]

Once you cut the second cat off could you send a wire up to the first one and dig it out? To avoid having to cut then resend it up?

[@rightcoastoffroad]

I'm sure someone could find out a way, but that stuff is really hard......would be tough to find something strong enough that is also flexible enough.

[@dirrtymurph1591]

Great video. Im going to wait until 1-26-2021. Kawasaki is releasing 3 new models. Teryx4 1000 is what I'm hoping for!

[@rightcoastoffroad]

I think you will see a KRX 1000 4 seater, a Teryx 4 1000 (64 wide) and a Teryx 2 1000 (64 wide). Lets just say a little birdy told me so 😉

[@dirrtymurph1591]

@@rightcoastoffroad ha ha awesome! Did that little birdie tweet of a V-twin 1000??

[@marka1712]

@@rightcoastoffroad I think your birdie lied to you lol

[@rightcoastoffroad]

They did. But don't give up hope just yet.

[@whynotjusttry5401]

@@rightcoastoffroad Birdy lied to you. I’m still waiting.

[@terrancesmith1674]

I love the sound of a vowing uncorked