2017 Ford F250 - B2 Audio 3 Ways in the doors! Custom 6x9 Adapters, Class A Amp Wired & Fired up

visit: www.stevemeaded... - Join our fun, friendly and knowledgeable community today!
Get Second Skin’s #1 Sound Deadener here
www.secondskina...
SMD Products can be found at www.wcCarAudio.com , Amazon, Ebay and more!
I know it has been a while but i finally got the doors started...and finished. The system consists of:
Factory Headunit (Sony)
Pac AmpPro AP4-FD21 Interface (Using optical output)
Audiocontrol DM810 DSP (way more than i need now but expandable for later!)
B2 Audio Reference 4 Channel (Class A or AB (Switchable)) on the Mids/Highs
B2 Audio Rage 2500.1 on the Subwoofers
B2 Audio Reference 6.3 Three-Way Components (Custom Starboard HDPE Adapter Plates)
(6) B2 Audio 6.5" Subwoofers in a Gately Audio ported, under seat enclosure.
SMD Quick Release Neo Magnet Terminal (to take box out at night or when space is needed)
SMD Fuses, Fuse Blocks and Power Distritubion
Skyhigh Power Cable
SMD RCA (From DM810 to amps)
NavTV FD 360 Camera Control
Second Skin "Damp Pro" sound Deadener
Wiring harness used Pac APH-FD01 (to get into the doors).
I pulled my boot and door plug out to try to find a way in through the molex plug like i normally would...but there isn't room for ANYTHING. I think because my truck is fully loaded all the contact points are being used. When i go fully active SOON, i will drill the necessary holes and run new wires. For now, this works GREAT!
I know this was a long video, but if you watched it all, thank you! I will make a video soon doing some basic tuning to get this thing souding even better! I also have a BRAND NEW improved Gately Audio under-seat box i am going to swap in. The one i have now is a prototype, one of the originals and he has since improved them. I have it at the shop ready to go! And then, i am going to put 4 8" subs in another under-seat box after that! I have plans in the future to expand the system that is why i used the Audiocontrol DM810 DSP. It has way more channels than i need right now but i would rather have too many than not enough! And YES, i will probably eventually switch to fully active. Right now, i just wanted it all working and sounding good..and it doesn't just sound good, it sounds GREAT. And it's still flat! I can't wait to throw some pink noise in it and an RTA! Stay tuned! And make sure you hit the notification button, i have lots of fun stuff for 2020 planned!
#Ford #B2Audio #Speakers
Support these videos here! / meade916
Also, check out my other pages:
Instagram: / meade916
Facebook Page here:
/ smd-steve-me. .
Follow: / meade916
Visit Sonic Electronix at www.sonicelectr...

[@meade916]

these adapter plates will be available to the public soon! they fit 2017-2019 ford f250 Superduty trucks. I plan on offering them in 2-way components as well as single and double 6.5’s. 5 1/4” too! Did i mention i also plan on offering the fully loaded ready to go? Check my webstore www.wccaraudio.com in a few days i should have at least these up.

[@shaneoverton9256]

Ok thanks! I would love to do everything your doing to that truck to my 2017 Platinum. I have a nice 2 10 box under the back seat with sundown subs and a crescendo amp but want more. Do the 6 smaller subs compare to double 10s ?

[@MrMamasdaddy]

@mead916 do these b2 subs offer spl as well sound quality? Compared to say a 12w7?

[@dougwilson377]

Yezzz zirr!!!

[@MrShake1013]

Gotta make them for the 2020 Silverado 2500HD too.

[@kiabass8798]

Chyeeh

[@AR_ZACK91]

Offers still available if u want to borrow 200 and pay me back years later with a system lol. 🤷🏽‍♂️

[@fiercenet]

Sick! I'm glad for some reason manufacturers are still using 6x9s otherwise this wouldn't exist!

[@cruzalexiscollicolli5993]

Juanito

[@cruzalexiscollicolli5993]

Foto

[@britishlingo]

What are your favorite 6x9’s

[@WokWithEddie]

Love the setup and the free lesson in how car audio is suppose to be done. Thanks for sharing your knowledge and style. The wiring on the doors look A1, never seen any other audio shop go into that much detail. Good job Steve! 👍👍👍👍

[@paulsalmon4771]

I can't help it Steve's workmanship is insane, unmatched, incredible and so many more adjectives to describe his abilities WOW!!!!!!!!! brother man wow...

[@mrtastytrim1130]

I love this install series but I'm still waiting for a sound system to be installed in your Escalade!

[@MS-qp3ju]

Me too

[@jonanderson4474]

That's three of us so far.

[@mrtastytrim1130]

Maybe if we get enough people to agree, he will start on that install? 🤔😮

[@meade916]

a million people agreeing wont get my amps here faster 😂 they are being powder coated right now so relax :) thanks!

[@MS-qp3ju]

@@meade916 yes sir

[@xTinBenderX]

Sweet 3 way plate! Be interesting to see if the 810 necessary or if someone could just use an LC using the passive crossovers. Can't wait for the tuning video! Been trying to learn all I can about these DSP units before I drop the coin, but I think I can get away without one using the head unit's crossovers and time alignment.

[@nhdetailpro]

Your workmanship and attention to detail is insane. Nice job!

[@That_Car_Kidd]

Most people might not be interested in watching wiring but that was clean af 👍

[@mikethatguy27]

It's a shame the door isn't clear just to show that workmanship and quality and attention to detail. SMD is on the next level.💯🙌✌️

[@MS-qp3ju]

My grandma said she needed hearing aids took her for a ride today blasted those two 15 's she said ohh I can hear again 😂😂😂😂😂

[@jody024]

Bump that Sinatra!

[@danielwilson6665]

@@jody024 , Sinatra ??? I’ve heard of that dude. He and his associates weren’t called homies or anything else from the modern era of stereotypical identifiers so commonly used. Of course they were all into sex, drugs and the hipster music that the young at heart old folks were snapping their fingers to long before rock and roll took possession of every living soul on earth. Sinatra was the head honcho of this small group of cool cats from the entertainment industry. They were called the Rat Pack because their lifestyle would make Ozzie blush. Isn’t it frightening how the older generation swings 😳. I heard that Frankie had a totally bitchin Victrola installed in his ‘40 Ford 😎.

[@breakerbroke23]

I dig the red white and blue spk wire coding, I always put the scrap damping material behind the driver on the outer door skin. Scrap is scrap....Cheers

[@JMKady76]

Doors are so convenient to work on with the truck at that height. no kneeling or sitting on the ground.

[@meade916]

actually it wasn't too bad. Glad i have those Amp side steps though for sure :D nice and wide, with grip on them.

[@ryandarby3460]

@@meade916 😂😂😂my grumpy 67 year old step dad is gonna look at me funny when I start calling his side steps "amp side steps"...great video, as always, Steve

[@MrMaxyield]

This video clearly shows how important Proper planning is when building your system... 💪💪💪👍😎

[@RadDadisRad]

That sub enclosure is 👌🏻. I bet the port bazookas air onto the back of your arm when it’s on the arm rest.

[@richardcrim3831]

I love this dudes time lapses. Does anyone else agree that Steve meade is the best at using Not Annoying NCS music.

[@scottpeck1149]

When your dog barked mine got up to play with him because I listen through studio monitors, live action sound with 15" reference sub, also we listen to the same music in background, probably your line arrays? Effortlessly loud and clear.

[@meade916]

ya he wouldn't shut up LOL!! he was talking for a bit in this video if you listen he was just jabbering away :D :D

[@adaboy4z]

That Bracket and speakers to pretty to hide behind the door panel. Clean precise work!!

[@thewibb]

This dude is a friggin ARTIST! Respect that work! 💯

[@rodneyhickman598]

Man i can only imagine how good that sounds.While sitting in your truck..Nice really nice..

[@danielwilson6665]

When it comes to online audio “experts” , there’s an abundance of them and the horse shit they try to pass off as legitimate technical information gathered from their impressive experience and vastly superior custom installations, can be easily recognized by its putrid smell. Fortunately there are certified and trustworthy companies like SMD to provide accurate test results along with reliable installation information for many great components Thanks Steve !

[@tonyzeno2715]

those components look absolutely gorgeous... I wish had the fabrication skill to make things like this..

[@alanstant9356]

Man do those b2s get it all the way Steve. Sound awesome on geadphones. Thanks for sharing.

[@ccvideotech]

Awesome work and awesome helpful tips this video. I love to see the multiple smaller woofer setups, something a little different.

[@Wack_to_wac]

Just bought the combo pack for smd dd1 and cc1. So excited. I was about to buy a o scope. Saw the comparison and absolutely mind blowing. I hot a Orion XTR.2500.1DZ (2948rms @1ohm 12.6) and massive audio 12 3000rms. So pumped to have it set professionally!!

[@vineshen3599]

Your work is outstanding ... Better then factory machine could do Mr Meade

[@crujones6204]

Those adapter plates came out awesome. Nice job. I am always impressed by your work

[@Chris_Wolfgram]

Love watching the master at work. Wish I knew 10% of what SM does about car audio...

[@MsRob5150]

Oh my God those are too nice to be covered up !

[@vader.editz.86]

Damn beautiful job on those B2 Audio 3 way speakers bro. They slapped hard even without the subwoofers hooked up. Keep up the awesome builds.

[@shadresanford5146]

Those B2 3way speakers and adapters are super sexy!!! Hell of an install.....

[@SeanOMatic]

Sundown, DC Audio, Ampere, B2 Audio...All of them use the same OE (Erisson) for these speakers. I'd love to see how many speakers Erisson ships versus a manufacturer like Kicker or JBL.

[@bigvell02]

Wire job clean and safe & the adapters for the doors... Proper!!!. Man I swear every time I get done watching your videos I want to do something bass related. I think I will sneak a few panels to the wood shop at my job and get busy on my lunch break. Keep up the great work!

[@paulsalmon4771]

amazing ingenuity with that tweeter rig bro

[@jeffwallace8437]

Let's make sure they fit first.. as I suspected.... Fits perfectly!!

[@adampilkington8379]

You are so awesome @ everything you do Steve!! Car audio master this world will ever see bro!! Cheers!!

[@rvadventures]

Love your stuff. Just can't afford it I'm sure.

[@josepharagon8259]

I am really impressed, the fact that you show the mistakes… now I don’t have to make those mistakes lol great job guys

[@rubensilvarocha]

Actually i had this type of speaker install in my Ford 12 years ago. It's the Ford Fusion european "brother" and i can say that it works best if the plate is mounted upside down. The highs in the bottom and the woofer at the top.

[@loudaagoo]

SMD & B2 Audio FTW.. always innovating.. one of the top audio trend setters for sure, thanks for the awesome video Steve 💪🏼💪🏼

[@willowwonderbull7100]

and shows your computer modding skills with the wire loom great touch as always

[@marauder0284]

Thanks for making the speaker rings will get a pair for my 16 f-150

[@MarxismIStreason]

Nice..! I always find myself turning to short dog, or 40 when tweaking levels. I've yet to pick up any of your SMD essentials, but it's on the agenda. I'm assuming that I won't be turning knobs constantly once I do get set up. Thanks for the vids, nice truck\build.

[@BLUE200S]

Damn id give anything to work w you meade :/ always been my dream. Wish i could see your face if you saw my builds. N here i am again years later watching your vids again

[@squirtmph]

Beautiful work, totally clean work installed. I wish professional shops would do install equal as yours. I pay big Buck for nasty labor & tuning up

[@joeymerrell8585]

I need this exact adapter for my truck. Awesome job once again.

[@Finga_Trappa]

I will watch allllll 40 min, at least a couple times guaranteed!!! Nostalgia🤷‍♂️

[@meade916]

ShiftyKing’s Guid2TheGalaxy 👍🏻👍🏻👍🏻💯💯💯💯

[@raiderraymond2173]

Came out nice thanks for the videos

[@rickdodson5252]

Nice video...just got my cc-1 today. I can't wait to play around with it.

[@aileenswhiteboy]

Make your life easy and get that Milwaukee 18volt best gun install looks great always love your work

[@kennymayberry126]

Damn. I'm definitely gonna be looking at the straight 6x9 to 6.5. As always great work

[@maxspl1]

Off the hook great install LOVE IT 😜

[@amanteapasionado6836]

I love systems that sound like that

[@CKH_Transport_llc]

Awesome build. I've enjoyed watching all the videos and seeing it all come together. Nice Job Man!

[@xasthurhead]

Love b2! That must sound so clean and good especially for crankin bury me in smoke haha

[@jjon4220]

super professional/factory looking.

[@djkritical9606]

That was a great audio flex in the beginning lol

[@Soulgasm08]

It’s crazy how good those look. Wow

[@cadecadjew8195]

Correct me if I’m wrong but I think f250 and f150 are similar so this may be a two way deal

[@chuckmalone2798]

Nice job Steve

[@ryanduerr6875]

I like the RED , WHITE , AND BLUE!!! color scheme on the wiring..... 🇺🇸 Am I the only one to notice that?

[@ryanduerr6875]

Huh!?

[@soniclab-cnc]

that Laguna laser is super smooth.

[@Cameraworksltd]

Another solid fab with my favorite b2 audio. Nice work.

[@paulhewson4600]

Dr. Meade performing surgery,,,,

[@raygandavis7707]

Those adapter's are off the chain.👍👍👍👍👍👍👍👍👍

[@anthonymyers-35]

Beautiful man, don't know how I missed this one..

[@jesseviewmont8343]

top notch, like always at smd.

[@jreamsnyder]

F'n awesome as always. Thanks for putting out the great content and great work Steve!

[@amomentsnotice]

Just keeps gettin better Wow so interesting

[@ronjlwhite8058]

That truck is friggin dope all around!!! Bad ass system too man nice job!!!

[@juliourdapilleta5580]

Como siempre gran trabajo Saludos desde México steve

[@jaredclinton7348]

Would love to see those speaker adaptors go up forsale.

[@flspeid]

10:18 Boyz in the Hood Quote: Dammn, that sh*t's bumpin' !

[@ianchildress5484]

Nice always with b2 💯

[@emaccapone4799]

I also like to get those quick releases a must have

[@EmpireBreedingCo]

master craftsman all day.

[@jdizzlebizzle2044]

Steve meade is the man . I need a system install homie

[@332sjbender]

Like watching Bob Ross. Creating a masterpiece one router stroke at a time.

[@bingbongbingbingbong7251]

Professor Meade Chopin the 2017 gang

[@kikejr5551]

Awesome programming ,awesome work ,it speaks for it self 100%👍

[@ljmike1204]

Steve is going eco frendlie speaker spacers out of cardboard.... lol

[@markward6474]

Very nice work! I am curious to your get thought of placing all 3 components in the door vs. doing some in the pillar. At first glance, it seems like the factory grill in the door may be a little small to get max output from all 3 drivers. I appreciate your feedback.

[@meade916]

nope they sound great.

[@1aquariustechguy]

Dope as always!

[@dubsdeuces]

Steve always does Grade A work. Big or small.

[@XKawN916]

Alright, I'm sold. Gonna get these b2 6.5's for my 66 mustang. Now, what else to get, lol.

[@erik120719]

Man try black label godspeed and hellbound, fast tight double bass and almoat painful mids...makes my tnt 15s get loose

[@FRench-men-EN]

nice man ... it's gonna be loud with the 6 6,5 sub's

[@srp365]

Just noticed your plate. No kidding lol, hopefully it's no bad omen.

[@meade916]

Steven Pangilinan Badd with 2 D’s =good. 😎

[@josephs9268]

As always SMD makin it look clean clownin

[@mikegray9428]

nice work most shops would just glue that tweeter in.

[@benbradford8822]

Those are freakin bad ass!!!!!

[@robfalkner4303]

It sounds amazing Steve ! 👍🤙

[@meade916]

it does! thanks!

[@robfalkner4303]

Wish I could hear it in person.

[@Shanehuff1971]

I’d love a set for my 2017 Yukon. 3way.

[@snchillin]

Beast mode ,looks clean bro

[@CVLova]

8:25 we all make that face :D love the videos steve!

[@7470alexander]

Great job man, dang it man make me some of those 🙏🏼

[@aleemhosein6813]

Can't wait to see u tunr

[@lukeb8429]

Very professional as always well done bro

[@brendan747]

Notification squad sound off👌

[@khalidman23]

would these adapters work also on a 2018 F-150 XTL supercrew ? where can i purchase