24hp Stage 2 440cc Build | Billet Rod & Flywheel, 34mm Mikuni, .308cam, double valve springs

[@deannagrayston4778]

This channel is extremely underrated

[@shtrzrus]

Ya fuck cars and cameras

[@Christian-ve9vb]

@@shtrzrus 😂😂😂😂😂😂

[@sethenewman4309]

It has 310k subs hardly under rated

[@Jalen_Knight8526]

@@shtrzrus you probably Watch CarsandCameras

[@joshbannon8989]

You have mad skills at building motors. And fabrication. Impressive.

[@genemurphy4229]

Red beard with morning coffee...impact wrench sounds, and almost like watching Bob Ross and the sound of the brush stroke. Calming.

[@PotatoeJoe69]

Great thing about these Duromax big blocks is that the inside of the block is already clearanced from the factory for upgraded parts.

[@Parents_of_Twins]

Preferably get yourself a decent set of micrometers to measure your crankshaft to see if it is oval shaped. If all you are doing is small engines you could get by with just a couple mics. You don't necessarily need high end mics like Mitutoyo or Starrett. They are nice but cheaper mics work as well.

[@Parents_of_Twins]

I put a ton of assembly lube on everything in an engine. Last engine I rebuilt was a 4 cylinder Continental from a forklift and it takes a while for oil pump to pull up oil after a rebuild so I used around 6-8 oz of assembly lube on it. It sits and idles with 30lbs of oil pressure so must have done something right. It was my first full rebuild without any assistance. Helped my dad rebuild several engines but the first one I did by myself. Next I have a 6 cylinder IH diesel that I'm rebuilding. I have a 212 Hemi Predator that's going to be getting some work done to it as well pretty soon.

[@IngenTechNational]

Nice build Red Beard!!

[@kartnerds]

Reliable 24hp is solid

[@gilsonvideos2950]

I'm from Brazil I'm loving your work congratulations

[@thunderj176]

Big block powah!

[@jubileefan6079]

Thanks for the tutorial on big blocks, Red Beard! Looking forward to seeing how much it improves the gravy bones kart.

[@RedBeardsGarage]

You and me both!

[@anthonyrogerson6863]

7:34 looks like that crank got really hot

[@plusplus3]

This video was very good. Keep the engine rebuilds coming. Awesome job!!

[@transformationproject3583]

Very nice. I have a few gx390's sitting around was going to sell them but places are starting to run out. I gotta small, very similar to lil red, kart that im thinking of replacing the 212. I may end up getting another frame, this one is my go to and pretty nice for a 212. I weight 265lbs and hits over 40mph and doesn't jack around getting there. Out of all the karts I have it always starts 1st or 2nd pull and is ready to go. Its the only kart that's remained intact over the years I could go ride it right now.

[@joeyornelas4316]

Great build always great to watch and learn something new

[@hammerdown5568]

Need a one year review of this engine

[@mikesbarn1858]

Thank you for all the great build information. I’ve learned a lot from you.

[@RedBeardsGarage]

Thanks for watching!

[@randytravis3998]

don't forget too check carb linkage when you remove starter cover and reinstall it when carb is on .. you could pinch linkage and you could be full speed when you start the kart .. don't know if you could run fast enough to catch the cart to stop the engine ..

[@89Interceptor]

thats why you put the thing up against the wall when you go to start it for the 1st time after doing something like this

[@randytravis3998]

@@89Interceptor i use the chain hoist or a jack myself but works the same .. hate to see people get hurt thats why i said to check the linkage .one kart i used a logging chain other owner had the carb turned up too high for low speed .. that one had elec start i was in it lucky me it would have went threw a ditch if i was not ,,

[@dr.auggie1109]

Thanks for the upload big red

[@nickdifilippo4055]

Do your engine build videos do well? I like watching them. Thanks for all your hard work.

[@Mk4switchez]

lol i love the donut mo powa baby

[@trumpfancardanostakepool4737]

Excellent. Love the engine builds.

[@RedBeardsGarage]

Glad you like them!

[@davidowen888]

Gravy Bones 😅I love it

[@jddj6110]

Do you have a favorite air filter for a stage 1 non hemi predator 212? I race go carts on dirt and in my class we run modified predators witch are basically stage 1 predators with the standard upgrades and nothing internal, the only think I know of that’s different is relocating the gas tank and adding a fuel pump witch shouldn’t change anything performance wise, and also my engine builder said they modified something in the valves, I can’t remember if it’s stiffer springs or just lash but aside from that I was wondering if you had a favorite performance air filter that gives you the most horse power with stage 1 jetting but also filters well since we run on dirt and it can get pretty dusty, every little gain helps on the track, thanks, keep building 👍

[@kwcslvr1]

Great content Greg. Follow up on how well reusing that head gasket works for ya.

[@briananderson3620]

Why doesn't anybody use the hole from the governor for a crank case vent

[@mikesbarn1858]

If you intended reusing the original gas tank it won’t fit. Unless you can find a low profile 90 degrees.

[@Rebel-Neck]

I used it like that but I had made an oil cooler for mine and that's where the oil fed back into the engine. It worked pretty well untill the bottom end came apart. I used all stock internals but Frankensteined a 196cc and a 212 together for ccs in the head and I had like 50 lb clutch springs for a KTM dirtbike that I used for valve springs. My 212 was running 60mph on stock internals, with a drilled and ground stock flywheel (big no no for safety) and I had the 34 mm makuni. At one point me and my buddies lost the exhaust pipe so we ran it shooting flames out the head and it ran like a raped ape.

[@cyode123434]

Remember when you gave Launie (sp?) hell for going to deep with the hone? Pepperidge farms remembers.

[@codyarmes652]

I bought a engine off of y'all a week ago and trying to figure it out trying to put it on a chopper bike

[@AliMardanNaqvi]

This helped alot i have a GX390 can i use a 420cc engine piston on a 390?

[@FJ80Coop]

Just a heads up..you cannot get an accurate torque holding the block still with your free hand while jerking on the torque wrench..1 or 2 bolts hand tightened is sufficient on the side away from the direction of torque to give a much more accurate torque ... Also,never ever snap the torque wrench bouncing it off of the click... Simply pull on it slowly and steadily until it clicks and then ease off the pressure... Also you may reuse any gasket that hasn't failed or been compromised by applying a thin coat of enamel spray paint allowing to fully dry before applying a 2nd heavy coat allowing it to fully dry before reassembly.. Any V8s,v6s,i4s,i6s,v4s,v2,single cylinder gaskets as long as they're not an o ring type... Also always apply break in lube to every single friction area or rotational assembly and bearing when reassembling or assembling any engine.. Well worth the minimal investment costs during initial start up and break in...

[@heavymetalmadman3533]

awesome vid. what grit was your de glazer hone ?

[@daltonmccourt1141]

What pushrods did you use. I just bought the chromoly pushrods that you said to use in your other video. Just trying to figure out the length before I go through and measure everything and cut them.

[@Jalen_Knight8526]

Where did you get the circular recoil start all of can find for the Duromax engines is the backwards D shaped recoil start?

[@SoLoCruizer]

thats a true beast imagine on a mega moto frame

[@blakejewell8209]

What separates this one from the 30hp one? I’m trying to get a list together to build the 30hp one but a lot of the links aren’t there on the old video of the 30hp

[@witosarlaw]

Mantap bang...🙏👍😊

[@jakeholcombe4002]

Old vid to comment on but what were you using to mount the slide carb on?

[@impurfektprojectsgarage1688]

I am looking for a crankshaft for my predator 212 non Hemi so I can get to work building it

[@jesuspamorada6718]

Hello how to purchase and how much thanks?

[@househouse5889]

Where did you get the table top swivel?

[@seanlott430]

On a stock 440cc with the governor removed how many rpm can you spin them

[@calpol-bn2gp]

🐐

[@JoseLopez-eu3nh]

Hey red beard, I have a offroad gokart with a 420cc engine with the 40 series torque converter and my driven keeps popping when I press the gas even when I'm going straight on a flat road it still pops , I don't even give it full throttle??? Any recommendations?

[@Strict30]

Did you use dual 65s brotha

[@markstreet7431]

Is the duromax 440 engine considered a hemi motor

[@RedBeardsGarage]

No it is a non hemi

[@BogdanLW]

how much billet flywheel weight?

[@codyarmes652]

How do you run your lines different on a fuel pump on a 98 CC side shaft engine

[@Nitewatch-xc9yz]

Is there a way to do all this and keep the electric start?

[@joecannon5043]

what were the different rocker arms you threw in after removing the stock ones?

[@williamedwards7315]

I have a mini chopper on building I just put a 208cc on it I think I haven't geared way too high I have six snowmobiles so I'm going to be putting a big mikuni carburetor on it 34 mm I have 38 mm but I'm going to use the 34 I have a 14 tooth clutch with a 36 tooth rear sprocket and the bike will barely take off from a dead stop and at 35 mph seems like it's idling and would go way faster but I'm hoping putting a larger carburetor on it will help it get to its top speed but I'm probably going to have to get more teeth on my rear sprocket or less on my clutch

[@jhekstv1382]

Whats is the messure of your camshaft lobe..

[@piebag]

Your the fuckin’ man boss thank you so much for all the amazing content please keep up the great work!!! 👏👏👏

[@nickclashez]

Got any built engines for sale ?

[@keithw372]

what kind of power do you get when done with the stage ?

[@TheGdcb]

18 stock stage 2 is 24hp

[@kalonrick1]

Red beard what size are the bolts on the intake manifold???

[@MachinesWithDavid]

Please I need help finding the retainers for this engine! I’ve been stuck for a couple months due to searching, I lost 1 of the tiny little retainer pieces😢

[@csm9291974]

Can you tell me how much this motor weights after these mods ?

[@minhtritruong5522]

Siêu phẩm

[@SeanStratton-ql1sf]

I can't. Wait. For. My. Kits. And. Motor. To. Come in. I been. Dieing. To get. My hand. In. One. What's. The. Time key. Red if u. Don't mind me asking. Is it. Advanced. 4. Degrees. Right. I now. They. Use to. Do that. On. The. Big block.

[@Johnnyreengo]

How do you know it makes 24hp

[@nobdurbin1951]

Do they make Gaples rings for this engines

[@randytravis3998]

you need the gap rings get longer when there hot if they were to touch tip too tip when cold there would be no room for them to expand .. so no gapless rings ..

[@connorssmallengines6663]

@@randytravis3998 gapless rings are a set of rings that use 2 piston rings that ride inside each other, meaning there is no real gap

[@randytravis3998]

@@connorssmallengines6663 OK MY BAD

[@ericmuhlbeier8023]

I wanna see someone recreate the uncle tony-vs- engine masters "piston flip" mod with one of these engines... see if it makes a difference on a small scale! Also the 3 stone hone is far superior to the dingle ball hone

[@6pack102]

Can I run a stage 2 but not use the bullet flywheel?

[@baocong1364]

Hay quá có ban máy không bạn

[@micahpoling6467]

I posted this on an older 440 build you did but maybe I can get more help here. I was going to build this tame setup. So I called GoPowerSports and they said they don't do have a kit that works with DuroMax 440. They were very unhelpful as far as compatibility. Any suggestion? should I buy there kit anyway and see if it fit? It looks like yours fits and runs ok. So are the 420's and 440 mostly identical? Thanks

[@RedBeardsGarage]

All parts used on this engine build are linked in the video description.

[@micahpoling6467]

@@RedBeardsGarage Yes, I saw that. I'll take the gamble and hope they fit, even though the guy at GoPowerSports says it will not work. Obviously it worked out for you. Great video, thanks!

[@daltonmccourt1141]

@@RedBeardsGarage where is the push rods I can’t find them

[@sonvo138]

Helo những linh kiện này bạn mua ở đâu

[@erikdaniels5628]

What was the significance of drilling the carb insulator

[@CRAZEDX100]

Pulse pump signal

[@Jrdnsmn14]

What’s the rotating platform called that your using?

[@randytravis3998]

it was there under the engine

[@dumbasscountryboy]

A lazy Susan. Lol you can buy them on Amazon for cheap.

[@transformationproject3583]

@@dumbasscountryboy Im married to one

[@jay-are9037]

@@transformationproject3583🤣🤣🤣🤣

[@ViyonceCanillo]

how much 18hp

[@newbornlog2789]

I gotta get ahold of fonzi from Plasti dip to get my rods checked dip yo car I mean journal wait what... hahaha jk

[@mikesimon9529]

I see quite surprised that you actually know the top and the bottom I am impressed😃👍👍👍✌😁

[@mindovermatter3988]

Love the videos but you said Plasti Dip instead of Plasti gauge. Hopefully some people don't get it mixed up

[@williamedwards7315]

I'm putting a 34 mm carburetor on my 208cc mini chopper do you think that will give it a lot more power than the stock carburetor???¿??

[@gracierbeltran6203]

I would like to order that's kind of parts and my engine is HONDA Mega marine gx390 from Philippines😊

[@kichca83_pin]

Tôi muốn có nó

[@Saucethe1]

24hp seems low for a 440cc i have a 34mm setup on my 250 came stock with 19hp now its around 28hp

[@613Builds]

ring squeezer cam follower plasti dip

[@laule3404]

cho tui 1 con máy dk hk

[@blakefain4489]

Plasti gauge does not replace a bore gauge and micrometers. Plasti gauge is not a true measurement. It’s a guesstimate

[@transformationproject3583]

If its good enough for taryldactal it's good enough for me

[@blakefain4489]

@@transformationproject3583 yeah no

[@bradenrnp3687]

That hone job looked terrible it’s supposed to be 45 degree cross hatching not horizontal scoring

[@randytravis3998]

that's when you use the ball device it will give it the cross pattern .. the stones do not ,, he said he did not have the other tool yet ..

[@kartnerds]

I let another guy use his balls last time. Cylinder looks good but now I'm in therapy.

[@bradenrnp3687]

@@randytravis3998 he should put a scrambler 400 engine in a go kart that would be the fastest thing he’s ever built just 1500 in performance stuff they can make 75hp and more money will get close to 90hp on race gas

[@mikesimon9529]

Sometimes you impressed me as sometimes

[@annabelbustillo1937]

Hi I was post to play with your kids

[@davidjessee7701]

No way would I delete the electric starter.....just me though....

[@airsoftgodfather]

Always makes me cringe when people are building a motor and they go full rip on the hone instead of a slow spin and quick up and down strokes to get a 45 degree cross hatch. Too much rpm on the hone like that creates a very tight cross hatch that retains a lot of oil (smoker) AND causes more wear on the rings at the same time 😬

[@DetroitMicroSound]

Wanna hear something funny? I can show you several late 1970's single cylinder rotary inducted 50cc two-stroke GP bike engines, that make nearly the same horsepower.

[@DetroitMicroSound]

@@billwilliamson9842 They are 100mph+ bikes with 5-8 gears in the box. With an average sized adult man on the back they have all they needed to be part of the world grand prix championships. How is the rest relevant? WHAT, is what you thought, smart guy?

[@DetroitMicroSound]

@@billwilliamson9842Whatever dude. 😆

[@baocong1364]

Hay quá có ban máy không bạn