3 in 1 BMS 3s, 4s, 5s || 12.6v - 16.8v- 21v || 25A BMS Battery charger with protection board

[@leonelalvarado4879]

amigo es bms no tienes que quitarle unas resistencias para utilizarlas en las diferentes combinaciones???

[@maatiraouki9124]

C’est excellent merci beaucoup pour l’exercice

[@irfansensoy5901]

Hello. I am using the same bms module. There are 2 of them, 1 is used and 1 is never used. I made the connections as in your video, but the voltage on the output pins seems exactly half of what it should be. For example, the voltage of the batteries connected in series is measured as 20.8 volts, but at the output pins of the bms circuit it is measured as 10.4 volts. I apply a voltage of around 24 for charging, but the bms circuit does not perform the charging process. The same problem applies to the old and the new.

[@powergen522]

hello, first of check individual battery voltage second clean the BMS Board using acetone or any liquid then check BMs terminal pin and connection circuit diagram

[@arupamdutta1]

Hi... if I use BMS 3S 10A then let me advise which adaptor would be the best for charging? Your circuit is really helpful.

[@sammy2888]

Hi Power Gen , great video , but now they have more advance BMS board in the market with 10 MOS , is your 4cell suitable to use with the 40A board , your advice please .. tks

[@solsticex9010]

Please ,can you make 36v Batterie from 4× 9v Batterie?? I want this for my escooter Thanks

[@wiled2320]

Hello friend, I have the same bms board, but I bought it for 5S, and the 5s does not have the three resistors next to the positive with a value of 0. Therefore, it could not be configured for 3s or 4s. I have simply made a bridge for it and now I can configure it. This is done by the manufacturer to be able to put three different prices according to the cells. If you make a video explaining it it would be perfect, if you want to do the test to remove the three resistors you will see how it does not work. All of this has taken me a while to figure out. Thanks and sorry for the translation.

[@fabcentnom2990]

5S it's 5S bridge = short circuit = error

[@divikumar5475]

Hi there nice video, I wanna build a battery pack, should I go with 1S10P configuration with boost converter or 3S4P configuration for 12V application?.

[@SMARTEK-INFO]

Go for 3s 4p To avoid losses and high cost of materials

[@solsticex9010]

Can i charge 5 × 9v Batterie with this bms Board??

[@Vagubando]

Do I need to connect (weld, solder) batteries to the BMS board in sequence (from plus to minus or vice versa) how is it in the laptop battery so that the board does not go into protection?

[@VARocketry]

So using 5S, if you wanted , say, 19.5v to drive LED strobes, I guess you could wire in a separate output leads to a LM2596 Buck converter to limit the 5s final voltage to 19.5v, correct?

[@powergen522]

LM2596 module is maximum 3A Output capable but your light lamp is minimum 10A required, so choose the DC 6-40V To 1.2-36V 300W 20A Constant Current Adjustable Buck Converter Step Down Module Board With Short Circuit Protection Function board, i have given the product detail link- www.banggood.in/custlink/mKvm28kzqG

[@VARocketry]

@@powergen522 SPECS Voltage: 12V DC Amperage: 1.39A Power: 16.7W The manufacturer says their strobes require 1.39A so I thought the 3A limit on the LM2596 was sufficient.

[@powergen522]

you can use 0.8-28V CC-CV buck converter www.banggood.in/custlink/3GvGJ0LpML

[@samueloneill3246]

So where can I connect the 12.6V output to a device? Do I use the same output as the load and charger?

[@darshitmathur145]

Sir mere pas 12v ka smps adapter hai jo around 15v ka output deta hai..mai usme kya katu ki mujhe 12.6v ka output mil jae...thank you

[@victoroliveroing]

How many 3S parallel bear this module? It is clear that works to 3S but I havent clear how many parallel can receive. 3S2P? 3S3P? 3S4P? 3S5P? Thanks

[@y-linkengineeringgoodlucke6229]

Please what is the liquid you are applying on top of the battery before before soldering ? Because the problem we have is sometime soldering on top of the battery is somehow difficult

[@nickspace6230]

Flux

[@nwfalls]

Great tutorial on how to do everything wrong!

[@MARK.NAN69]

Hi bang...Nak tanya boleh...Kalau kita pakai bateri 18650 1 biji kena guna bms 1s..klau 2biji bateri 18650 2s, dan 3biji bateri 18650 kena guna 3s...ke macam mana

[@VARocketry]

Do I understand that this provides 3.7 x5= 18.5v max, or is it 4.2x 5= 21v? I read 18650 max voltage is 4.2v.

[@powergen522]

yes, the battery is full charged condition is 4.2 *5=21v

[@anasaliyarkunju6746]

How to charges this battery type of 12vot 21volt and 14vot and which adaptor is used for this

[@shmuelnaarai677]

Can this protection board be used for cordless tools?

[@ScienceFunInnovations]

Looking forward to trying this on future projects.

[@electronic7979]

Very good 👍

[@ki4npx]

Where can i find a switch that will go from parallel to series....on 3 batteries, 18650...12.6 to 4.2...which will balance the batteries in parallel.... Or can we make one .....I have tried and the wiring is crazy....

[@nageshgaikwad8895]

Please provide your soldring iron buy link

[@y-linkengineeringgoodlucke6229]

Love you your channel

[@toppervikingo]

Halo Power GEN :-) I like your video. I have the same BMS board. My problem is that I can not charge my battery (3S). I can discharge but not charge. Do you have any suggestions?

[@powergen522]

maybe the board is damaged, but finally, try this method. first fully disconnecting wire again reconnecting the wires.

[@toppervikingo]

Thank you for advice @@powergen522. I tried at my 2 BMS, but still the same result. Ah, it is sad. Any other god recommendations:-)

[@kuntal.chanda]

@@toppervikingo use 2a adapter

[@Ankit_M]

Plz add Voiceover For Better Understand

[@powergen522]

i will try

[@laurenceguevarra219]

How many amphere 3s 12.6v battery pack

[@herbertvonsauerkrautunterh2513]

I need this but smaller to fit in power tool battery pack

[@mosesduha]

👍

[@somtirtha.m]

soldering LITHIUM ION battery is not recommended bro.

[@ssworld5107]

Nice

[@isratshamimlaily5849]

Okgood

[@PranavKumar-fy7bg]

Its a dangerous way to charge a battery with a power supply which didn't have the support for controlling the amount of current going into the battery.

[@isratshamimlaily5849]

Nice 👍👍👍👍👍👍👍🇦🇷

[@wiled2320]

I guess you sell these bms and you are not interested in the trick, sorry friend.

[@powergen522]

I bought it on my own, then one of a best all in one BMS board

[@normandejesusgarsiaarteaga5902]

Porq enla salida meda de 1.10v Y deveria de ser de 12v

[@yavuzkayalar1767]

Teşekkürler...

[@maatiraouki9124]

❤️⭐️👏✌️👍

[@constructionwithskills488]

Zuban Ni h Kia?

[@biplobkhan479]

Very bad your meter display problem

[@akmaltojeng3890]

Abang orang mana

[@cholito1949]

It is imposible to see the connections. Bad video

[@sirsmokealotofkush5857]

He included a diagram for each circuit