3126 overhead valve setting by Ocean Marine

[@kluna1000]

Great video! Thanks for sharing.

[@daltonshaw3317]

so on the feeler gauge between the rocker arm and the bridge how is it supposed to feel ? sticky ? or free of resistance ???

[@Ranjit_media]

nozzle settings Which one will I do in the first round?

[@حساماليمني-ت5و]

I want this digital device, how can I buy it?

[@bobocaterpillar3697]

9:27 exhaust is supposed to come out the turbo... not the crank case breather...waaaay to much blow by! DuPont rebuild?

[@misters2837]

That is the most *RETARDED* Comment on this entire video... You OBVIOUSLY have NEVER Overhauled an engine in your life! - Takes HOURS for all the new wear surfaces to "Break In" - Many Times they will consume oil for the first 10-20 hours...Sometimes LONGER Depending on the composition of the rings and liners (or block in this case) - I have overhauled 1,000's of engines of all types... That "Blow-by" is QUITE NORMAL...

[@حاتمالصلوي-ظ5ض]

كم يكون خلوص النوزل بالجيزول

[@berenicerobles4654]

Hola tengo un problema con un 3116 se acelera y no pará casi a desbocar se Lleve los inyectores al laboratorio y no puedo con esa falla Alguna sugerencia que me den Les agradecería mucho

[@JorgeReyes-ft6pz]

9:59 en la punta del inyector lleva un sello ...si se rompe pasa el disel directo a la cámara de cobistion

[@marcoinestroza6904]

Me falla la inyección del motor 3114 cuando toco la cremayera se aselera el motor no se como evitar eso

[@mromar7877]

Merci

[@reyrojasgarcia5032]

Thanks, it' s good.

[@genivaldocosme2305]

ola amigo gostei muito doi jeito de trabalho e como divulga a mecanica

[@Mint-pg5ng]

If you reduce the injector hight to 63.88 mm it's gonna be less smokey

[@dariuszkomin9507]

7:49 - Someone could give me a dimensions of this calibrating tool? I need a hight to set a mikrometer ( Exacly like at this Video). Thanks a lot

[@operatorchanneltv]

Nice bro

[@emrahozdemir5206]

Hello, Why have engine blowby ? I think for the new repaired engine is abnormal. Thank you

[@daltonsequipment4419]

Emrah ÖZDEMİR because it was just rebuilt and the piston rings haven't seated.

[@JorgeReyes-ft6pz]

9:59 eso es motor descomprecinado

[@chryslerny413]

That 3126 looks a lot like a 3116

[@plcwboy]

Well, they are the same except for displacement.

[@jairobetanco4854]

quiero saber cómo calibrar un motor carterpilar 3126 electrónico la calibración completa

[@joselinvalera3454]

Jairo Betanco Los injectores se calibaran con el scaner Las valvualas normales

[@abu.maryam]

احسنتم ولكن هذا محرك 3116

[@محروسعبدالهاديعرابي]

رائع جدا معلم

[@mikeyx8]

Can someone tell me the name of the tools... btw great video

[@rh_apin9746]

Tools for injector syncronizing ... My be the name is tools timing group 🙏

[@alexandercontreras3247]

@@rh_apin9746 ola

[@zainpakistan1797]

Nobody is hearing me i want valve adjust 4 cylinder gep 65_3 it is 60 kva generator and plz engine firing order where i see 6 cylinder plzzxxxxzzzz

[@miguelangelzeagonzalezzeag9789]

que onda conpa que 64 parejas o que onda

[@josh29356]

3116

[@roeurnsopharin6048]

Thank

[@emmanuelakram4279]

Ok

[@edantasdantas7507]

Are you mute ? I see there that you are full of finger does not talk about how?

[@leopoldoramirez4307]

No c les entiende las calibrasiones no esplican las bueltas para lnyectores y balbulas

[@JorgeReyes-ft6pz]

9:59 yo lo sé comunícate

[@elvinsanchez7962]

ermano una pregunta