#372

[@kjmwtube]

You, sir, are a GODSEND! Very clear and concise instructions. I'm NOT a mechanic; and, I'm petrified at the thought of disassembling multiple parts on my car's engine, to accomplish a task. You saved me from that nightmare. And, I believe I will never forget you, because of your singular kindness, of producing this particular video. It's given me the courage to tackle a vexing problem, that, I did not have the understanding to explain; the way my car seem to be running less efficiently over time. I was getting dismissive responses from mechanics, suggesting that because my car was old ('95 Toyota Camry), I should be resolved to ACCEPT, that, my car should NOT be expected to run well again. Thank you for giving me hope, to remain in a car that I am happy to own.

[@zerolabs]

Git-er-done!

[@sajidmohammad3190]

Man you don't know how much I've searched on this topic...but I haven't found any good video...finally yours one helped me...thanks a lot!

[@victorsparks3408]

This was a brilliant and very timely video for me. On my way home one night this week I discovered that my rpm was fluctuating between 1500 & 2500 every second. I had an important commercial inspection job the next morning and my '02 Toyota Highlander was filled with equipment I did not want to have to load into a rental. I found your video and got up the next morning at 5am, followed your instructions and got to work on time! But, wait -there's more! I have put 170,000 out of the 225,000 miles on this SUV and I have NEVER had this kind of MPG before. Two months earlier I noticed my MPG had dropped to 18.6 -I am now averaging 21.5 after only my first tank of gas since the IAC valve cleaning. I believe the valve has been sticking for years. When I started the ignition on the morning of the repair the idle was stuck at 3,000 rpm. This is the single most important and satisfying repair I have EVER made on ANY vehicle and I have you to thank for it. Thank you for taking the time to share your knowledge and for doing it so clearly -YOU ARE THE MAN!!

[@zerolabs]

Victor Sparks My head won't fit through the door today! :D

[@wellnesspathforme6236]

I second this. The details are i.portant here, and without them it is easy to be misled. Which I was, until I saw this video. I hope this information can play a role in helping to get of my family's vehicles performing substantially better. Thanks for sharing. Note -- I will plug the bottom hose nipple with a piece of bent or clamped tubing. 15 minutes with my finger under that thing is asking a lot.

[@josephsteffen2378]

You were TRIUMPHANT! Yeah, most people wouldn't know where to start. Hey, we all have talents and skills, but Automotive repair is grueling, dirty, painful, and not the most lucrative trade... All mechanics go through the trials and tribulations...torn skin, smashed fingers, purple fingernails, black specks on the pillow case, the aroma of petroleum products(greases, oils, cleaners, gasoline, smoke-electrical/plastic/paint.....combustion, sweat, etc. Oh yeah, I've been the cause of some fires...even burned a shirt a few times. Getting back to you... in our lifetime we have seen huge paradigm shifts in Automotive technology. Going from carbureted engines to fuel injection. That's just one example. ...just when you began to get a grip on venturis, accelerator pumps, emulsion tubes, transition circuits, chokes, ...they are made obsolete by fuel injection. Time to go back to school. Yeah, you succeeded. MAJORLY! (... you said that it idled smoother and mpg improved). I don't know yir skill level, REGARDLESS it's satisfying.

[@milo6373]

@@zerolabs vacuum line went back to the vacuum reservoir on top of throttle body , good info , ☝️✌️👍💪🤔

[@MrOTcomputer]

This man is what we would call a “TC Technician”. It is the highest level there is. Having at least 20 years of experience. It’s always a pleasure to watch a TC Technician work. Absolutely brilliant and 100% competent in anything he does. Thank you.

[@zerolabs]

That's a very nice compliment. Thank you.

[@someonethirsty1957]

TC?

[@siegfredreginaldo]

what is TC?

[@AndrewMattis]

After a year of trying to figure out what was wrong with my 97 camry (taking it to shops, replacing filters, full tune up, etc) this was finally my answer, Thank you so much for this video. It was very detailed on how this part works and how to clean it properly. 1000 thank you's for finally showing me how to fix my car.

[@nelsonramirez27]

what exactly were the symptoms on your car?

[@bayoupirate3808]

This is without a doubt the best video on cleaning the IAC valve. Thank You.

[@zerolabs]

Wow, thanks!

[@reuventhehotboy]

This is one of the best explanations for part of the air intake that almost nobody has gone so deep ever before , thank u so much sir !

[@tysoncruz3428]

Figured there was a problem when the engine was stalling in the mornings when the engine was cold and I came to a stop. One morning the engine stalled and I couldn't get it restarted. Did a simple KZbin search on "'99 Camry Engine Stall Problem" and watched a video that talked about the same thing as this video but didn't remove the drain hose. This one came up next on autoplay and was more detailed. I removed the hose and worked in the carburetor cleaner as suggested (actually used throttle body cleaner). I didn't completely remove the throttle body as he did in detail but I did remove the drain hose underneath. Worked in the throttle body cleaner for about 5 minutes and drained the cleaner. Whole process took about 2 hours from start to finish and it worked like a charm on a $4 investment on the cleaner. Thanks for the tutorial!

[@zerolabs]

That is SO GRATIFYING! Thanks for sharing your experience!

[@chris103193]

I did this on my 93 Camry le 2.2 due to a strong vibration while in drive or reverse, not neutral. Engine turns over much quicker now, drives smoother, and the idle vibration is no longer ridiculous. Thanks so much

[@ngk330]

I’ll have to try this and see if it helps my same issue, vibration in drive and reverse

[@kurticusmaximus]

I must say, this actually is the better method. I wish every repair video explained so clearly the mechanics behind why the repair works as well as you do. Thanks for this! I am doing this today on my V6!

[@zerolabs]

+Kurt Hutchison And did it work?

[@chinawok6956]

the best explanation on how to clean the idle air control valve... thanks you just saved me a lot of money.... thanks again

[@zerolabs]

Awesome! Feel free to donate a portion of what I saved you. ;-)

[@kimikimms8588]

very well explain easy way to clean IAC save a lot of time and cost for repair. dont take your vehicle to the dealer to repair this problem it cost me over $1k . thank you!

[@keithcitizen4855]

Ditto thanks -

[@plsmoothy]

I was getting ready to remove and clean my IAC on my 2001 Camry V6 and I stumbled on to your video. So glad I did! I will absolutely try this method first. Excellent discovery and a great job explaining how the IAC operates. Well done sir and thanks.

[@SONOFAZOMBIE2025]

+Internet RN same car, did it work?

[@danashton8571]

Thank you spent hours to day doing spark plugs ,leads ,fuel filter to fix my low idle and stalling. Your method took 5 minutes and job done

[@zerolabs]

+dan ashton OUTSTANDING! I never tire of success stories.

[@davidpeel8431]

Thanks for the tips and clear instructions, I followed them and cleaned everything up and my 2000 V6 Camry now runs sweet, thank you.

[@runthomas]

great stuff ..properly explained and relatively straight forward , as long as you dont get your hoses and screws mixed up.....or round any screws and nuts... this is a job for a nice sunny day ...all relaxed ..thank you. also well mentioned the fact that some people are just spraying throttle and carb cleaner into their pistons and engine.....which is not a good move..

[@charlesmiller5078]

Rarely do you see a video that comes all together, video ,audio, content. You nailed it.

[@robertparker496]

A must see video for anyone wanting to learn in depth operation of how the throttle and IAC works. I enjoyed the video. Thank you!

[@AikidoTubeSock]

Excellent video. When I change my fuel filter, I also plan to clean my throttle body and with this video, I can now clean the IAC valve. A few years ago I brought my car to the shop for idle problems and it cost about $75. Now I can do it myself for the price of 1/4 can of throttle body cleaner or about $1.50. Thanks

[@SerotoninGaming_YT]

This method absolutely works on a 1995 Camry as well. Thank you so much Zero!

[@SwervingLemon]

Thank you. Just fixed my son's 2001 Camry using this video. My idle air control does not have that down tube but exercising the actuator with the intake full of carb cleaner worked a charm.

[@zerolabs]

That just means you have a non-california emission version and the crankcase is ventilated elsewhere. Makes it much easier to perform this procedure. Glad it worked for you. You just saved $300 or more!

[@jnorhede]

Worked great, never had carbi cleaner so I used WD40, worked like a charm, you need a medal :)

[@robertr.garcia7043]

Finally, a video that makes sense & clearly explains things. I'm glad I kept searching. He's right, money"s tight, & good night.

[@slowvag8v]

Thanks, I fixed my car this weekend! It was idling as high as 1700 rpm and now it goes as low as 800 rpm

[@cruizer59]

Excellent contribution to the KZbin community! Thank you for taking the time to put this video together and share with us!

[@dcbyers1]

Thanks for sharing the post-iac valve removal wisdom...made the process quick and simple. Sienna now starts like a champ!

[@zerolabs]

Outstanding! Love reading success stories.

[@jeffsmith2145]

2000 Avalon. Banging my head against everything trying to figure out the problem. The car would not start unless I held the accelerator pedal down and then it would die when the pedal was released. Wondering about fuel issues. This did the trick (so far, as I haven't driven it yet). It has started right up three times and idles as it should. Thank you very much for posting this video. There should be a knighthood in it for you!

[@zerolabs]

+Jeff Smith It make me very happy to get reports like this of success. Feel free to leave something in the tip jar. ;-)

[@alamazhar2441]

Beautifully described the procedure of cleaning throttle body without removing from the car...excellent video with great information and tips.....

[@spottieott1]

My 2001 camry was running ar 1800 rpm when warm. Cut the a/c on and it will drop to 1400 rpm. Cleaned the throttle body. Same results. Watched your video. Cleaned the icv and magic appeared. Runs like new now. Thank you. Saved me alot of money. Thanks

[@zerolabs]

Very gratifying.

[@mikefindeisen6872]

Very nice. I really appreciate not having to remove the throttle body (although I've already got it off in my garage). Flooding that little chamber by plugging that pipe is genius! I got to the point of removing those 4 screws on the throttle body to crack it apart so I could clean those little chambers, like you did later in the video, but I could not for the life of me get those screws to turn...stripped like they were made out of lead. Sooo, I'm so happy I can clean that little valve without taking it apart...you just made my day. Thanks!

[@JohnJenkinson]

From looking at the video, that valve looked like a fishing reel.

[@laughinghyena001]

Well done, Sir. Excellent marks in presentation, description and instruction. I look forward to more Toyota repair videos made by you.

[@angelikajarin3702]

Hi! This is very helpful, I and my dad are having problems to fix a 2010 toyota camry, the engine will start for a while and then dies immediately. Now we know what to do this is very detailed instructions and tips. thank you so much!

[@captainwho1]

Thanks for this! My first attempt at cleaning my throttle body and IACV on my 96 Honda Civic EX A/T didn't fix my high fast idle problem but gave more acceleration. Either I didn't clean it well enough because I didn't remove the coils and rotate the magnet back and forth fully, or I need to loosen the two screws and rotate the plate a bit CW to get the valve to close further at startup temp (the one calibrated at factory). One way or another, your video serves as a pep talk to ultimate success hopefully.

[@MM-nc6xc]

Very informative! My 1997 Toyota Ipsum had the same problem, lucky I watched your video prior to cleaning my IAC valve which is exactly the same as yours. It saved me so much hassle for the job. My car is back to normal, thanks!

[@jamesferguson5398]

Followed your instructions for cleaning the IAC but only turned the valve controller back and forth for about a minute using throttle body cleaner instead of carb cleaner. You don't need to remove all the stuff you did to get this job done though. I only needed to loosen the backside clamp that connects the throttle body to the plastic intake tube from the air box and wiggle it to the side just enough ... then I unfastened the electrical plug to the IAC. Then I performed the cleaning like you have shown. This seemed to do the trick and my idle is much smoother especially when the A/C is on. Thanks for the tutorial ... the whole cleaning took me only 15 minutes from start to finish.

[@zerolabs]

Nice!

[@cle2hou1]

James do you have a 1997 Camry also, I'm a novice fixing cars and need the easiest possible method of repair my 97 Camry, what tools do I need, size ratchet nuts etc. Thanks

[@coollary1]

Thank you for taking the time to thoroughly explain what the issue was and how to simply solve it. This video was a great help.

[@zerolabs]

coollary1 Love hearing about all of your success stories!

[@robertdavis9986]

Great video. I've seen them spray into the opening and wondered where it would go....Now I see a better solution! much thanks. My 2000 camry is not throwing a code for IAC..just a rough idle intermittent when sits after warmed up.

[@orbnitsky]

Great job, thanks! I've done this before on other vehicles and I see the Toyota nuances to expect!

[@zerolabs]

Glad you enjoyed it!

[@charlesgloeckner9873]

Have been going crazy with this issue, now fixed. Great video and many thanks!

[@zerolabs]

Awesome! Love success stories!

[@Batti2323]

Enormously helpful!! I really appreciate the detail. I would not have guessed that plunger rotated magnetically. I will use this today. Thank you!!

[@nevermoresmith63]

Great video, man. I was about to spend money on new sensors and you saved me a kings ransom. You rock, also your other videos are great. Let me know when you build a time machine or particle accelerator

[@normahall6308]

my car is 1995 camry. 184,678 milage. its running fine. ill remember this tip. you did a great explaining and demonstrating what you had to do. i liked your music.

[@Billiemarie1000]

This was the best video on cleaning this valve. The others never said anything about it running down the center tube and likely why I could never do an effective job.

[@robgibson8319]

This worked great on our 2.2 95 Camry. Simple repair by cleaning the ACV, it was stuck, now have a very happy daughter who doesn't have her steering wheel shake like crazy in reverse!

[@zerolabs]

Rob Gibson Love all the success stories! Keep'em coming! :D

[@Mikepragland]

what a relief. My little toyota starlets been idling high for ages... after i left it off the road for a year. Tried this method and it's back to normal! - the little twisty bit was almost solid... bit of fluid and a twist around and its sooooo much looser. I owe you! thanks a lot

[@zerolabs]

+Michael Prag You're welcome! Feel free to leave a little something in the tip jar! ;-)

[@byb-bangforyourbuck2353]

super helpful u helped me not worry about CA smog/emissions test and not dread buying a newer or new car or be robbed by a mechanic/stealership

[@paulkresky1465]

What a great video! Thanks very much! I have an 06 Corolla I am preparing to do this on, and I wasn't looking forward to tearing the whole throttle body off. I have just subscribed and liked. Thanks again for the on car cleaning method. Have been systematically cleaning everything bit by bit.

[@davidharman4078]

Very useful, thank you for posting. Greetings from down under!

[@UberFlippy]

My 94 Celica has the same engine and basic setup here, and this helped me a lot. Thanks for the video.

[@samuelmichael7924]

It is a very professionally presented and explained with knowledge of IAC function and it is very helpful to me thank you so much for sharing your knowledge.

[@idreamincjreen]

This is a great video, thanks so much for posting it! It really helped clean out my IACV on my Toyota Camry 2001 and fixed the stalling on start-up problem.

[@danyao6122]

my 1998 Toyota Camry has this issue: sometimes very lower idle speed during starting the engine, the engine would stop if I release the gas panel. this happens sometimes, not very time. It happened 3 years ago, I had it serviced and worked well. now it starts to show the problem again. I went to car repair store and they would charge me $179 for the cleanup. that is quite expensive, so this time I will give it a try. Thanks for your video, this helps quite a lot! I will do it this weekend.

[@zerolabs]

Please report back how it went.

[@danyao6122]

@@zerolabs it works great, except it seems that the initial idle speed is too high (~1300 rpm) when the engine does a cold start, once the engine gets warmup, the idle speed is a little bit too low (~650 rpm) when I drive the car and stop due to traffic light. It might need the car computer gradually learn and collect enough data to get the 800 rpm at idle speed.

[@zerolabs]

@@danyao6122 Once it's cleaned and working properly, after the engine is fully warmed up and idling, loosen the setscrew that locks the angular position (slotted opening), fiddle with it and lock it again. This *is* the idle speed adjustment.

[@Holmberg_Audio]

Put a quart of Mystery Oil in the gas tank when full tank. Dissolves soot in the throttle body complex.

[@parkerlongbow]

I just finished fixing a fast idle and P0505 error in my nephew's camry thanks to your video. Not knowing better, just from first inspection it appeared that the IAC simply controls that vacuum dashpot right next to it, using that to regulate idle speed. Your video corrected my misunderstanding and clearly explained exactly how it worked. Thanks!

[@zerolabs]

Love it.

[@eVerProductions1]

Oh my lord Jesus finally a video that thoroughly explained how to simply clean this because I cleaned my throttle body and some of the carb got into the iac hole and my idle has been stuck at 1000+ but finally you have a good guide without taking off the throttle body

[@zerolabs]

You're welcome!

[@RogerPack]

For followers, his alternative method that "doesn't require you to remove it" is to "plug the large middle hose with your finger" while it's still on, that he describes at 4:00 then flood with carburetor cleaner.

[@christopherbenkeal2810]

Absolutely Terrific video! Thanks to you I was able to successfully clean out the IAC valve with this nice method. You are very thorough with clear explanations and it's much appreciated. If you ever replace or adjust the throttle position sensor or how to tighten the throttle cable please do a video.

[@zerolabs]

***** Well, after 250,000 miles I just recently had to replace the oil pump. Seals blew out so I figured it was time. While it was all apart I changed the oil pan and valve cover gaskets, water pump, timing belt, serpentine belt and hoses. I'll be doing some exhaust work later this morning but I ***REALLY*** hope that's it for a while! :-\ Thanks for your comment.

[@georgelie5589]

I also have a 97 Camry that has a similar problem: Engine stalls immediately when cold starting. It happened 3 times before and the dealers always charged me about $400 to replace IAC. I happens again now, but I refuse to take it to a dealer immediately. Instead, I searched the internet and realized that it seems to be a "unique" issue with Camry. Few websites suggest cleaning the IAC and show how to do it. But I found this Zero Garage to be the best: It not only tells you how to do it, it also explains clearly why.I did not flood the IAC as suggested. I just spread the cleaner few times while continuously turning the gate axis to loosing the gunk. It seems to work because now my problem is solved for $5.00! Thank you very much for doing such a great job educating me! By the way, I am not handy with cars. This was actually the first "major" repair of a car that I ever did. I feel great because I accomplished a $400 repair job!

[@zerolabs]

+George Lie I am Very happy to help you keep all that money in your pockets. Feel free to leave a tip. ;-)

[@georgelie5589]

Update: Gee, time really flies! Can not imagine it was a year ago that I posted this. I am really happy to report that my "major" repair is still going strong: have not had any idle issue since!

[@RadioWhisperer]

A great video, thank you so much! Been an engineer a long time, so I like to understand how the system works rather than just blindly follow a procedure. Thank you for explaining how it all works! I have an idle speed issue with my 2000 Camry LE (4 cyl 5S-FE engine) where the idle drops below 500 RPM and the engine stalls. But this only happens after the engine warms up. So I still need to dig into how the IAC works and see if not enough idle air is the root problem, or a symptom of something else, like bad vacuum or sensor. But you're video helped me tremendously, thank you!

[@agateenchantmentrockwizard5969]

Hi, I have a similar issue as yours with my 98 4Runner 2.7 it has the same IAC valve set up. Just wondering what your final results were on your Toyota? Did you do this procedure and did it help your "low idle" or was there more that needed repairs or replacement 🤔? Thanks in advance 👍

[@RadioWhisperer]

@Agate Enchantment & Rock Wizardry It worked for me. In the process of doing the repair i found holes that were letting air in behind the MAF sensor so that helped things too. But the car is on the road and running well. I hope it works for you too.

[@agateenchantmentrockwizard5969]

@@RadioWhisperer Thanks so much 🙏, I have and will continue to look for vacuum leasks definitely!

[@losesparkplug1190]

I sprayed a little sea foam and now it stays on when cold but today I will take the house off the bottom and then try that because its idles super low. No power drives like the fuel filter has never been replaced. Thanks for the good information!

[@noizemonger]

Any info on Camry regarding the vacuum system and repair, and or fuel system would be awesome, you sir are a teacher....i tackled the crank and camshaft seals, oil pump seals, water pump, timing belt and timing, throttle body cleaning, egr testing all from youtube and DIY guides...when i do these things feel a sense of accomplishment that's great and i urge more people to learn and take charge off life's hurdles...you can win sometimes. 39 and always learning!

[@Jlayism]

I've loved my 98 and 99. Both have experienced issues with the IAC, resulting in having to 2-foot the pedals to keep it alive. Going to try this trick to get it resolved!

[@zerolabs]

Confidence is high.

[@juansuarez6167]

What was your result after doing this procedure?

[@Jlayism]

@@juansuarez6167 unfortunately no change. When I disassembled the iac, there was zero build up of any kind and the parts still looked brand new. It still acts up every once in a while. Doesn't make sense, I truly figured this would fix my issue. I highly recommend doing it as a starting point for this type of problem though.

[@yeahyeah551]

Maybe fuel pump going out? I had this issue in the past with sputtering and loss of power at times and eventually lead to full failure of the pump where it refused to start at all suddenly. I am assuming the pump may be failing again. Could be worth a try. I will try this method and if unsuccessful i will do the pump again.

[@khengratha3264]

Thank your Video Uncle, It is pretty clear for me about the symptoms, Functioning and how to deal with it.

[@personalprivate7422]

thanks for showing how the valve looks and works, it helps understand what is actually going on. Great vid

[@zerolabs]

Glad you liked it!

[@iggyschnellmore]

Great music! Where did you find it?

[@scooter12368]

love videos when narrator gives explanations. good clear voice and pace of your speaking that helps. thanks

[@uncoban]

I did this yesterday on my 2000 Lexus ES300, worked like a charm. Took about 40 minutes. I used to just spray the little opening and would have to take it apart every couple of months because the engine would struggle or stall while idling. Saved me hundreds of dollars!

[@elysianfury]

Wow you're actually explaining how this stuff works... this is what I'm looking for thank you

[@imacf90]

i just bought a 97 mitsubishi mirage 4cyl. the setup is nearly identical, so this video really helps. i didnt really know what i was going to do to fix it. maybe i should clean it out before replacing the whole thing. great video.. thanks.

[@ivano.garcia5222]

ok. My car is a Camry 2000 and do not have that coil nor cable. I Just exposed the hole inside that metal tube, sprayed 1/4 Mass air flow sensor cleaner. When I tried to started​ the car, suddenly it doesn't started! But in the fourth attempt, it worked! It is better now. The car is working at lower revolutions and vibrations where reduced! Thanks a lot!

[@davidchandler1502]

You brought joy to my life, I want to follow you, and learn your teachings, oh wise one..

[@charlsseal7273]

Awesome video. Very clear. Oh, great music for the time lapse.

[@matiasfernandes]

Well, Ive just finished done this to my mother 94 Corolla (4afe engine). Let me tell you it worked great, it really does. This is the beauty of internet, where you can share crazy and usefull tips for almost everything you need. Great video once again man, take care

[@pjgolden5265]

Q

[@mkrp4]

When cleaning valve on the car, spray cleaner into the gap behind the throttle plate; use sparingly because too much cleaner flushes the gunk and carbon into the rear bearing of the IACV causing valve to stick (I did it once on my 87 Camry, so I had to get a used one from the junk yard.

[@golblum1363]

You sir, are the man! This worked a treat on my 92 camry. had problems with cold starts and rough idle- when it got to the shaft it would barely turn- a few minutes with the throttle body cleaner it freed right up Thumbs up!

[@zerolabs]

I love those success stories. Keep'em coming!

[@franklikespolitics]

For my needs, the best part of this video was learning that the valve was suppose to turn. Mine was stuck at first. I have a 2000 toyota camry Le 2.2. I could not find a drain hose on mine. The valve turns freely now but for about 3 seconds it seems to stick closed on the first cold start, I don't know if It need more cleaning or a new valve. Excellent teacher and video. thanks

[@zerolabs]

More cleaning.

[@steveDIY]

great video, just did this to my 97 camry this morning and worked like a charm! Thanks again for putting the time in for this video :)!!

[@rontownsend8235]

Got to respect a guy with like his, I can tweel that he stays busy all the time and don't worry about getting his dirty. That , my friends is a man that can fix your car and make it run right.

[@acebestwords]

Very helpful. My wife's car is 1999 Corolla. Not enough space to work/open the IAC. And need specialtool to remove the 2 bolts. I have to remove the throttle body. Thanks for the video. The best one that shows on how to clean IAC valve.

[@SuperHebbe]

Wish all repair videos was like this one :D Thanks a lot. I have a 1998 Camry that has never had any problems with the IDLE control, but I think I will clean it soon anyways just to be nice to my car :D

[@tomshiba51]

Now that method is a time saver.

[@zerolabs]

Except for the 16 minutes I make you sit through in my video! 😁

[@frankdooley6451]

Excellent, my 2006 Avensis is doing exactly what you outlined.

[@zerolabs]

I am gratified to know that I am killing this cash cow that dealerships and licensed mechanics know all to well how to exploit. Best of luck and please report your progress.

[@jayk806]

Wanted to say thanks. I wish I found your video a week earlier, as I already bought the new part, but even so, showing how to take the throttle body off, and that you don't have to drain the cooling system (as my shop manual suggests) means I might actually get this done this weekend. Thanks again!

[@zerolabs]

Great to hear!

[@cttc4132]

Terrific Video! Clear, concise explanation. Just add my comment to the chorus of approvals! Really appreciate your time and effort in making this excellent video! Cheers.

[@motorenergy4450]

I was searching for a method without taking the whole throutle body off. Thank you very much!

[@zerolabs]

You are very welcome!

[@wangruochuan]

thank you so much for the quick fix. I just did it to my gf's 2001 camry and it fixed the rough idle on cold start.

[@adamreveles5269]

on your 2001 there no hose like his how did u do it

[@wangruochuan]

Adam Reveles there is a outlet tube goes to crankcase at similar place. just pull it. you wont get wrong cuz its directly under the notch where you fill in the carbcleaner

[@pedro2836986]

Lol same car and problem with my girls

[@ithacalarry2191]

Great informative video! It's very clear cut, useful, and understandable. Now I'm off to my Camry to clean out the IAC valve. Thank you!

[@doctorjermz]

this is so helpful, i hope this works on my 94 celica tomorrow morning! thanks for putting this together and sharing.

[@danielmarques8904]

Fantastic job did it in my Toyota Rav4 1999, my idle was 1300 rpm warm, now is 750 rpm fantastic job.I also disconnect the battery for 30 min after the procedure.Thanks

[@zerolabs]

Awesome! Glad it helped you.

[@richardpaddon2675]

Thanks for the straightforward explanations and instructions.

[@nikovandh]

A+ video.. love how you showed the idle air control valve and the gate inside. Going to be cleaning my IACV and gonna hold my finger under the hole.

[@olgapking9172]

I learned so much from this video. My 94 Lexus looks similar. I've had it for a little over a year. Had it tuned up etc at mechanic when I bought it but it started idling very low and speedometer would not work for a few miles when cold, and would keep giving me spark plug codes. I finally braved it and decided to clean throttle body and mass air flow sensor. Even though I did not have the time to really do it this time, and for fear of breaking another hose, at least I learned what that notch was for and cleaned it somewhat. Anyway, the throttle body was horribly filthy so I can imagine that air control valve thingy, and the air filter. The car runs 90% better and I will take that part off next time when I can have someone with another car just in case. It did give me a weird code that just would not come off, I think a PO773. After finally arriving home after 74 miles, I turned car off, took key out then put key back in and just turned it to on without cranking and left key in for almost a minute and took key out and restarted car and code came off and did not come off. Thank you so much. I am a woman and could not afford a mechanic at this time or most other times

[@olgapking9172]

I meant the code PO773 came off and did not come back on but I can't wait to really do it like you showed

[@olgapking9172]

And the mechanics, don't know which, must have broken the part of the air intake hose that is connected to it so I had to crazy glue it at least for now. And of course they didn't tell me because that is not a cheap part

[@udidwht]

It isn't harmful to use the carb cleaner in the IAC port in the TB opening. It evaporates rather quickly when used in short bursts. It also saves time from removing the IAC and hoses.

[@TheDcrocks1]

What about break cleaner?

[@eddiewilliams6708]

Thanks for the video. A mechanic quoted me $550 to replace the throttle body of my 2004 camry. Went and bought a throttle cleaner and fixed the problem, but aafter watching your video, l am keen to have a look at the control valve and see what's going on in there cos the start up is still a little bit rough. Subscribed!

[@zerolabs]

It's criminal how they rape customers over "designed to fail" components like this. You wouldn't believe the venom spewed at me by "certified" Toyota mechanics for posting this video. Comical really.

[@eddiewilliams6708]

@@zerolabs They should be angry because the truth hurts. Keep up the good work

[@Hilux244]

Excellent information here, thanks for taking time to help out many. Only thing different I did was block the center nipple with a piece of rubber (inner tube) between my finger and the hole. Thus preventing carb cleaner from entering my bloodstream through skin pores. Thanks again!

[@zerolabs]

+Hilux244 Nitrile gloves work well too. ;-)

[@ediboyzee]

Thank you for posting this very detailed video. I have a 96 camry that has problem with the idle, there are times when I start it even when the engine was warm, the idle, is only at 500 rpm, I have to rev the engine for a few seconds before the idle goes to normal reading which is 800 rpm to 900 rpm.

[@hansschweikert9153]

Excellent video. Clear, concise, I've learned a lot. And you easily saved me $100 or more, plus the hassle of running vehicles all over creation. Thanks! Now if I can figure out why the battery light is on, even though the alternator is putting out plenty of power and a new battery...

[@viewer54322]

At 2:39 shouldn't there be a black o ring that seats against the circular area surrounding the magnet/shaft? Aside from that, I just used this same procedure on 2001 2nd gen avalon 1mz-fe, only difference was that the metal hose nipple that needs to be blocked is right underneath the spinning magnet, this nipple is angled and easy to access, I used a spare nitrile glove to block the nipple and then let the carb cleaner leak into the inside of the glove to dispose. p.s. as someone who loves learning about "why" and not just "how" to handle a procedure you have been one of the best explainers I have came across. Thanks for your time & insight sir!

[@mckoylach1622]

Thanks for your efforts and the elaborate explanations of how the IAC valve function....

[@ironhide590ify]

Thanks for the típ. I was looking for a bolt that controls the air flow into the plenum. And thanks to you I learned that it was the iddle speed control valve. Thanks again.

[@matiasfernandes]

Mi mother owns a 94 Corolla with the 4afe engine, it has exactly the same mechanism. It idles too high (1500-2000 rpm), tomorrow Ill try this. Its much more easy to do (less dissasembly). Thanks a lot for the video my friend, greetings from Paysandu, Uruguay PS: thumbs up for your video

[@billybob1723]

Great video. Nice job removing those Phillip's head screws. Mine won't budge.