This is awesome, printing your clips now. Thanks!!!
@Ms2204982 жыл бұрын
thank you for showing this fix,and much bigger thanks for providing file link,
@cashiefisaacs38152 жыл бұрын
Howsit bro! How long did the clips last? If I cant manage to print them can I buy a set or two from you? I am in Cape Town.
@Something313372 жыл бұрын
Howsit! The clips lasted me about a year until I accidentally leaned on my sunroof from the outside while it was open and shattered them 😂 If you manage to print them your side you'll have to print in ABS or anything better to withstand the temperatures from the sun on the car. If you don't come right send me a PM and I can't print you a set and we can organise delivery, I'm based in Joburg👍
@cashiefisaacs38152 жыл бұрын
@@Something31337 Courier shouldnt be an issue. Thanx a mil.
@michaelklein93074 жыл бұрын
awesome video!! keep up the great content
@Wergrun3 жыл бұрын
Will this work on an E91 moonroof? The smaller rear panel on mine gets stuck on the passenger side slider. Its either broken or gets stuck but it wont let the roof close from vent mode.
@Something313373 жыл бұрын
From the images I see on Ebay for e91 sunroof kits, it looks like a completely different slider clip design is used :)
@messinger1233 жыл бұрын
Thank you!
@laerciopaiva13 жыл бұрын
Awesome! Dude, i opened the STL in Cura and the dimensions are real small, can you tell me the real dimensions of the clips? Thank you!
@adrianmartinescu11073 жыл бұрын
Thanks! Export settings in my Autodesk were wrong, I've uploaded a fixed file now, let me know if it works. The length of the clip should be 54.306mm
@laerciopaiva13 жыл бұрын
Hello, Adrian. Everything is fine now. Thank you very much, let's print now!
@awn77754 жыл бұрын
Much wow
@tolga36uyan2 жыл бұрын
Sunroof legs are not broken, left rear 3 millimeters above right. In the case I mentioned, the inner floor is completely closed. Why might the right side be low? (adjustment slides fully open)
@adrianmartinescu11072 жыл бұрын
Perhaps try lowering the adjustment slide on the one side to half or all the way to minimum, and keep the other side maxed out? that should help level it out.
@tolga36uyan2 жыл бұрын
@@adrianmartinescu1107 Adjustment slider on both sides is highest. one side low and one side high. the difference is 3 mm. If I lower the high side it both side stays lower 3mm. When the sunroof is closed, the sunroof sheet stands 3mm lower than the roof sheet.(By the way, there is no problem in the operation of the sunroof). It would be better if I ask you with the photo, can you tell me where I can reach you ?
@adrianmartinescu11072 жыл бұрын
@@tolga36uyan sounds like the motor stop point that "clicks" the sunroof into the closed position is off by a little bit. Super easy fix, and it's in my other video as well where I install a new sunroof👍 basically you'll manually move the sunroof to the level closed position with an Allan key, then remove the motor from the sunroof to recalibrate, and then pop the motor back in and it'll be good👍 I'll send you my details and we can chat if you still stuck
@adrianmartinescu11072 жыл бұрын
@@tolga36uyan messages me on insta, linked in my KZbin bio and we can chat👍
@ОльгаТонких-Подольская3 жыл бұрын
what kind of program??
@adrianmartinescu11072 жыл бұрын
Autodesk Inventor for the model, Cura for the 3D printer code👍
@awn77754 жыл бұрын
I didn't keep my positions. Had to recalibrate
@nicolaashuysamen20342 жыл бұрын
Can i by a set from u
@adrianmartinescu11072 жыл бұрын
Where you located? I'm from South Africa and shipping may be expensive