Vorweg - du hast echt gut recherchiert! Hier mal ein paar ergänzende Punkte, die vielleicht jemandem helfen: - die Gleitlager die du bestellt hast, würde ich in der Form nicht verwenden, da die Linearführungen starr ausgeführt sind. Diese Lager mögen absolut keinen winkligen Versatz bzw. ungleichen Abstand der Führungen. Sie könnten klemmen, da die Toleranzen der Lager im Vergleich zur umliegenden Konstruktion zu eng sind. Die Führungsachsen sind nur grob ausgerichtet anhand der Lager und dann verschraubt. Es fehlt in der Konstruktion einfach eine genau festgelegte Position der Achsen. (Wenn man alle Freiheiten in der Konstruktion des Druckers hätte, würde ich ein Gelenk auf dem Schlitten zwischen der Lagerseite mit den zwei Lagern und der Lagerseite mit dem einen Lager schaffen. Dadurch öffnest du einen Freiheitsgrad, um den Versatz der Achsen auszugleichen.) - Ich habe vor kurzen selbst einen Prusa gebaut. Die LM8UU Lager kommen mit einer unbekannten Schmierung. Daher würde ich empfehlen, die Lager komplett mit Bremsenreiniger zu spülen und anschließend mit einem guten Fett für Führungen zu schmieren. Es gibt extra (gedruckte) Schmiernippel um Fett zu den Kugeln einzubringen. Es geht aber auch wenn du die Bohrung des Lagers gut mit Fett füllst, eine Seite mit dem Daumen verschließt und von der anderen Seite die Führungswelle einschiebst. Damit presst du Fett in jede Ritze. Die Lager anschließend eine weile auf der Welle bewegen, damit sich das Fett verteilen kann. Dadurch wirst du eine deutliche Geräuschreduktion bemerken - aber ganz leise werden sie nie sein. Vorteil dieser Lagerung mit Kugelumlauf ist, dass du dir kaum Gedanken um die genaue Ausrichtung der Führungsachsen machen musst. Die Lager können geringe Abweichungen ausgleichen. Zusätzlich hilft natürlich, die billig China Lager gegen hochwertige auszutauschen. Also zusammenfassend: Sehr gute Recherche zu den IGUS Lagern, aber für den Einsatz in dieser Konstruktion (Prusa) nicht wirklich geeignet. Die Toleranzen sind zu eng, um die ungenauen Toleranzen der Konstruktion auszugleichen. Gute LM8UU nehmen und anständig schmieren.
@abwesend182 Жыл бұрын
English Version - no support for correct translation xD First of all - you have researched really well! Here are a few additional points that may help someone: - I would not use the plain bearings you ordered in this form, because the linear guides are rigid. These bearings absolutely do not like angular misalignment or unequal spacing of the guides. They could jam because the tolerances of the bearings are too tight compared to the surrounding construction. The guide axes are only roughly aligned based on the bearings and then bolted in place. The design simply lacks a precisely defined position for the axes. (If you had all the freedom in the design of the printer, I would create a joint on the carriage between the bearing side with the two bearings and the bearing side with the one bearing. That way you open up a degree of freedom to compensate for the misalignment of the axles). - I recently built a Prusa myself. The LM8UU bearings come with an unknown lubrication. So I would recommend flushing the bearings completely with brake cleaner and then lubricating with a good grease for guides. There are extra (printed) grease nipples to add grease to the balls. But it also works if you fill the bore of the bearing well with grease, close one side with your thumb and push in the guide shaft from the other side. This way you press grease into every crack. Then move the bearings on the shaft for a while so that the grease can spread. You will notice a significant noise reduction - but they will never be completely quiet. The advantage of this recirculating ball bearing is that you hardly have to worry about the exact alignment of the guide axes. The bearings can compensate for minor deviations. Additionally, of course, it helps to replace the cheap China bearings with high quality ones. So in summary: Very good research on IGUS bearings, but not really suitable for use in this design (Prusa). The tolerances are too tight to compensate for the inaccurate tolerances of the design. Take good LM8UU and lubricate decently.
@cziasai Жыл бұрын
Super double interested. Please post result video! Thanks
@COOLwith2Os Жыл бұрын
I was JUST researching the exact same thing for hours before I found this Video. Even saw the Reddit post and Prusa Threads about it. I was hoping to find an up to date video about the bearings, not 4-5 year old videos with the cheaper pressfit bearings. So.. either I wait for your video or just buy the full set with rods and test it out myself!
@John-gm8ty10 ай бұрын
did you end up testing yourself?
@samoworks4648 Жыл бұрын
For anyone who's interested, I've uploaded a video about my experience of swapping to IGUS RJZM bearings and rods: kzbin.info/www/bejne/eHy8hKyOq5hjoM0 Not the best quality video but I hope it helps with people who's struggling to make a decision.