3S 12V 18650 10A BMS Charger || Li ion Lithium Battery Protection Board

50x21x1mm 10A BMS Charger Protection Board for Pack of 3 18650 Li-ion lithium Battery Cell
Input voltage: 12.6V
Over-charge voltage range: 4.25-4.35v ± 0.05v
Over-dischage voltage range: 2.3-3.0v ± 0.05v
Size: 50 x 16 x 1.0mm
Maximum operating current: 5-8A
Maximum instantaneous current: 9-10A
Operating temperature: -40 -- +50 ℃
Storage conditions: -40 -- +80 ℃
Quiescent current: less than 6uA
Effective life: more than 30,000 hours
Internal resistance: less than 60mΩ
Short circuit protection: protection, delay self-recovery.
The protection board size and device description
The protection board size is 50 x 16 x 1.0mm, components for the S-8254AA protection chip and genuine FDS 4435A x 4
ＬＩＫＥ | ＣＯＭＭＥＮＴ | ＳＨＡＲＥ | ＳＵＢＳＣＲＩＢＥ
=== = = = = = = = == = = = == = = = == = =
== = = = = == = = = = = = = == = = = = = ==
★★ Please like and subscribe ★★
/ @yellowpurple
=== = = = = = = = == = = = == = = = == = =
How to extend wifi range with another router wirelessly
• How to extend wifi ran...
Hack ip camera easy way
• Video
How to extend wifi range with another router
• How to Extend WiFi Ran...
WiFi Jammer/ Deauther || A Simple HomeMade Wi-Fi Jammer by using an ESP8266 | DIY Project
• A Simple HomeMade D.ea...
sokoban level 11 solution
• sokoban level 11 solution
Diy Arduino Based Ultrasonic Radar System || Using Ultrasonic Sensor & Servo Motor With Arduino
• Diy Arduino Based Ultr...
How To Connect wirelessly Two Routers On One Home Network Using WDS without cable
• How To Connect wireles...
How to Make Water Overflow Alarm With Led Indicator Save Electricity & Water
• How to Make Water Over...
4 Ways to Turn off a Normal School Calculator Citizen CT-512
• 4 Ways to Turn off a N...
Amazing Wireless Voltage Detector, Home Made Non Contact Tester #BC547
• Amazing Wireless Volta...
Top 10 Electronic Project With BC547 Transistor, Tri AC, LDR, LED, Photo Diode
• Top 10 Electronic Proj...
Automatic Plant Watering System Using Arduino Uno || YL 69 Soil Hygrometer & 5v 1 Channel Relay
• Automatic Plant Wateri...
Build your own Wi-Fi Repeater or Range extender using NodeMCU || WDS Bridge ESP8266
• Build your own Wi-Fi R...
Wifi share one router to another router without any cable (WDS)
• Wifi share one router ...
Making Use Of Old Router As Wifi Repeater Without Cable | Wifi Extender | Switch
• Making Use Of Old Rout...
10 Simple Tests And Experiments Identify Your Honey Pure or Fake 🐝🍯
• 10 Simple Tests And Ex...
Battery Charging Led Indicator Circuit || Monitor Battery Is Charging Or Not || Diy Charging Circuit
• Battery Charging Led I...
World's Smallest Amplifier PAM8403 (HW-104) || Mini Digital Amplifier 3W Board
• World's Smallest Ampli...
How To Repair Led Light || Fix SMD Led Light || Led Bulb Repair
• How To Repair Led Ligh...
★★=== = = = = = = = ==★★
Contact us for any enquiries :
[e-mail]
rubel1628
★★=== = = = = = = = ==★★
#yellowpurple
#bms
#3s10a
=== = = = = = = = == = = = == = = = == = =

[@sharpmerciful787]

2:22 Okay, so it is actually the 12v power supply that actually charges the 18650 batteries. The BMS is not what actually charges the batteries. That's all I wanted to know because I've done tons of google searches on this and nobody could provide me with the answer I was looking for. Thanks.

[@yulodede]

Don't charge it directly without the BMS for safety

[@mike65120]

OK, in one scene you have a standard 12V charger plug connected to the board and then connected to, probably, a standard 22V wall charger. The next scene you show a usb socket. What happened? Is that usb now your input and output? Why would you use a usb to transfer 12V??

[@aceyorkvillanueva7660]

That's what i want to know, where is the charging input. Thanks.

[@christianmannel6413]

By all 3 cells having 4.2 V =12.6 V their at 100 % SOCIETY. Charger or BMS should protect from over charging , what obviously does not happen. Looks to me like a huge lack of understanding the risks of a thermal breakdown

[@RixtronixLAB]

Well done, keep it up, thanks for sharing with us :)

[@GearGuy]

How are you charging it from USB-C? What voltage, what power supply? If you are using PD then are you using a cheater cable to get 12v? How are you achieving CCCV (constant current, constant voltage) at 12.6 volts from the charging cable? Thanks.

[@YellowPurple]

Charging Voltage: 12.6-13V

[@vinigretzky97]

@@YellowPurple What happens if you only supply 12V? And btw, this board is just a BMS right? Would you would still need a proper Li charger?

[@ClemOnShow]

@@vinigretzky97 This is correct a BMS does not handle the lithium charge but its discharge. To handle charge you'd need a TP4056 or a TP5100 per cell. In that sense the video is a bit misleading as the lithium chemistry doesn't have a great lifespan with a constant voltage and constant current charge.

[@vinigretzky97]

@@ClemOnShow Thanks for the info!

[@jumbo999614]

what adapter's voltage and amp to charge this battery through bms?

[@niteshkumawat]

Mere bms board se output nhi mil rha h kya kru.. Sab connections sahi h but no output plz tell me solution

[@elsaidyoussef7462]

If you please who can I add extra 3 batteries to increase A

[@miteshdhanani]

As u have made this, I would like to ask you if we want to make it of 7.4v and connect with a 3A 8.97v solar 3A, then

[@honeybadger2371]

So the output is also the input?

[@YellowPurple]

YES

[@pkpadiyodi4615]

Thanks sir and one doubt is that size of charger capacity used for charging 3 bms lith.battery..please send reply.

[@easywebsolution7044]

Good idea, I will try

[@moulifactsofficial]

BMS output not working...? Any solution for this...

[@honeybadger2371]

You connected it wrong probably

[@antoniecolisao9031]

How to determine if the battery is fully charge?

[@sharpmerciful787]

That's what I wanna know too. There's an induction heater thing that I'm learning about. It's like a 16 oz Starbuck induction heater for a Dynavap M Vaporizer. There's a green LED connected to a momentary push button that lets you know when it is pushed (green if pushed or nothing if released). Then there's a blue LED connected to a toggle switch (1) if powering by 18650 batteries, 2) if powering by 12v power supply, or 3) off.) In the diagram, it shows that there should be a GND wire starting from the main wires and connecting to the blue LED, but I don't know how you'd be able to do that without doing a lot of splicing of wires, which is where I'm lost. I believe the 18650 batteries get charged by the 12v power supply? Someone has also wanted to put 2 more LEDs, a red one and a green one indicting whether the battery is charging and when it's fully charged, but they don't know how to do it.

[@RJGamer-zb4lb]

how did you get a charging light?

[@jumbo999614]

I want to know that too.

[@razvanlungu6175]

the output is 12 v 10amps ?

[@minsyang]

This input charge for 12v? I think charge with usb power.

[@talhaijazprojectlimited5295]

Not get output in this bms,i also input the charge but not getting output from point p+ and p-

[@YellowPurple]

To active / get output, first time need to input charger

[@talhaijazprojectlimited5295]

@@YellowPurple i charged overnight but no output

[@rhhumanity4960]

Ma sha allah 🥰

[@alih.alwaily]

How much the maximum input voltage ?

[@YellowPurple]

12v

[@yangyiaung5858]

Thanks

[@shrinidhiachar8790]

Hey...Can I use a 12V 1A adapter as input source.....?

[@YellowPurple]

yes

[@chrisracer2007]

If the cell can charge up to 4.2V with only 12V will it get fully charged?​@@YellowPurple

[@manlang2002]

Better put diode 1a onto input charging

[@rithulrithu1783]

Can i use 5v charger

[@YellowPurple]

no, use 12.6v to 13.6v

[@rithulrithu1783]

12v normal charger

[@YellowPurple]

@@rithulrithu1783 yes

[@rithulrithu1783]

3s 12v 18650 10A bms charger| Charge level indicator video

[@drnikhileshkakkar5317]

would you like to sale it without the batteries, ?

[@cp1855]

Slow down