Is your store /website still operational? I have a charger I want to build.
@steedu46gt4 жыл бұрын
Did you have to modify the moe grip?
@gynocentrismergomgtow5 жыл бұрын
Can you add in the description a list of the ammo you have used in the Charger thus far? The more specific the better.
@joshv065 жыл бұрын
I'll post it here: 40gr CCI Blazer 36gr Winchester Western 40gr Federal Automatch 40gr Mini Mags The 36gr western is the only ammo I get supersonic cracks out of (because it's slightly lighter and therefore faster)
@mitchcairns41205 жыл бұрын
What tripod do you have for the chronograph?
@joshv065 жыл бұрын
Amazon basics tripod. Cheap and does the job.
@gynocentrismergomgtow5 жыл бұрын
Is the barrel 4.5" long from end to end or from one end to something else? For example from one end to the other but not including the muzzle threads?
@joshv065 жыл бұрын
Bolt face when chamber closed to end of the barrel. Just like any other barrel is measured.
@DaveSmith-cp5kj3 жыл бұрын
Barrels are always measured as if you drop a cleaning rod down the muzzle with the action locked and you measure the amount of rod that went in. The sole exception to this convention are revolvers, which is measured from the muzzle to the forcing cone. You don't include the cylinder length into the equation.
@edhlavaty69145 жыл бұрын
My 10 and 15 round mags cycle perfect. The 25 rounder is a pain in the Ass. Used the Copper Custom ,side folder with the Kak Blade
@bdL915 жыл бұрын
With a 4.5 barrel, is that OAL still over 26? Curious because I was thinking of doing something similar and wondered if that's SBR territory
@joshv065 жыл бұрын
Most likely not since it folds
@bdL915 жыл бұрын
joshv06 Ah ok so this is an SBR then? Not a pistol?
@joshv065 жыл бұрын
@@bdL91 it is just a pistol
@bdL915 жыл бұрын
joshv06 I got tripped up by the OAL thing. I forgot 26 OAL applies to rifles and that this was never a rifle.
@Sharberboy3 жыл бұрын
My 4.5 charger is 21 inches oal, 14 folded.
@gynocentrismergomgtow5 жыл бұрын
Have you heard supersonic cracks at all while shooting 40gr standard velocity rounds?
@joshv065 жыл бұрын
Never.
@bakernathan982 жыл бұрын
Try the kidd recoil spring polished guild rod kit helps alot with reliability especially when running subs with a short barrel I run the 10% reduced spring in mine .
@joshv062 жыл бұрын
I have it now with the standard sitting and it shots just fine with the standard spring and blazers.
@pozog8987 Жыл бұрын
@GodIsGood are you running subs with a 4.5 inch barrel or something longer?
@bakernathan98 Жыл бұрын
@@pozog8987 I run cci standard with a 10.5 inch barrel and a suppressor i have since switched to the standard enhanced spring that all comes with the KIDD kit .
@LithiumKnight Жыл бұрын
Is this gun a restricted? And if so, does anyone know if it is legal in Canada?
@gruntspy445 жыл бұрын
Ok you got my attention
@mariosuarez71265 жыл бұрын
Interested in the bearing spacer??????
@joshv065 жыл бұрын
I didn't have time to film that video. Subscribe and I will for sure release it soon!
@YPShaun2 жыл бұрын
Can I buy a 4.5 barrel for my ruger charger without a tax stamp?
@joshv062 жыл бұрын
It has to be a charger pistol
@YPShaun2 жыл бұрын
@@joshv06 okay I have the ruger charger with a 10” barrel but I am planning on switching it out for the 4.5” barrel. Can I put a stock on it or would that make it an sbr?
@joshv062 жыл бұрын
@@YPShaun that would make it an SBR. You need a brace.
@YPShaun2 жыл бұрын
@@joshv06 appreciate it
@rodelpalapar51254 жыл бұрын
where's the best deal for 4.5" barrel?
@joshv064 жыл бұрын
Best deal is to get your standard barrel cut, crowned and threaded down to 4.5" by class 3 machining.
@DaveSmith-cp5kj3 жыл бұрын
What he said, but rather than sending it out to be done, do it yourself. Use a hacksaw or ideally an angle grinder with a cutoff wheel to cut down the barrel, buy an annular cutter to create a shoulder and the proper diameter for the threads, then a TAT and a 1/2x28mm die to run threads down. Filed down the muzzle flat with a file, then rub some lapping compound on a brass round headed bolt with a slot cut down it, and run it against the muzzle to establish the crown. In theory it isn't as good as a lathe operation, but I have a lathe and I still do it by hand sometimes because it is convenient (you don't have to remove the barrel which can be a pain on other firearms) and you really don't see a practical difference in group size at the end of the day. Isn't as much work as you think, and will allow you to do these kinds of barrel threading operations for a bunch of other firearms you probably own or will want to thread in the future.
@mmmmmm82644 жыл бұрын
but the longer the barrel the faster the bullet?
@joshv064 жыл бұрын
Yeah, we purposely cut down the barrel to keep bullets subsonic for suppressor use.
@olcapone30393 жыл бұрын
SOUNDS SO QUIET
@gynocentrismergomgtow5 жыл бұрын
9:55 Even with the flash hider, that would be too close for my fingers/hand/peace_of_mind.
@joshv065 жыл бұрын
It's still impossible for my thumb to get in front of the muzzle if my hand is on the AFG.
@PETERPARKERPECKER4 жыл бұрын
joshv06 couldn’t you just add a small vertical grip instead?
@DaveSmith-cp5kj3 жыл бұрын
@@PETERPARKERPECKER Not supposed to put a vertical grip on a pistol or it turns it into an AOW. You can use the slightly canted vertical grip like BCM makes. This being said, I don't care if people infringe on gun laws. Gun laws itself are an infringement on the supreme law. I may not do it, but I'm not going to tell people that they can't do it.
@DaveSmith-cp5kj3 жыл бұрын
You can always use a fake silencer, or one of the muzzle compressor flash cans to serve as a barrel extension. My suggestion is to use one of those solvent traps and just leave the endcap and baffles out. This is legal, but also gives you a practical alternative if WORL.
@TVisTheRetina5 жыл бұрын
I don't get it. What is the point of the PMACA chassis if you already own a Charger? It's a pretty expensive add-on, Cerakote option makes it even more expensive, the Charger lets you add AR grips already and a $50 Copper Customs adapter lets you add any AR stock. Why buy this?
@joshv065 жыл бұрын
Copper custom adapter and a regular chassis adds length. Plus you cant put a suppressor on a stock chassis after cutting down the barrel without heavy modding.
@TVisTheRetina5 жыл бұрын
@@joshv06 If I cut my barrel down so it'll be long enough to work with the stock Charger chassis, will it still be supersonic?
@joshv065 жыл бұрын
@@TVisTheRetina it will. 4.5" is essential as you can see from the chrono test.
@reverse24 жыл бұрын
thank you for asking this and thank you @joshv06 for answering. I've been wondering this whole time I'm seeing these builds.