Thanks again Rob. As usaul your better information than two guys talking incoherently with a professional camera man filming them.
@celticdude46863 жыл бұрын
Thanks for the heads up. Good to know.
@CUTTERUPROB3 жыл бұрын
You bet
@Gunbanter2 жыл бұрын
Great info
@robertwinterstein66903 жыл бұрын
Was it the shaft in the rotor, on your bad oil pump that burnt up the Wagler rod and if so would you recommend brazing or welding?
@CUTTERUPROB3 жыл бұрын
the shaft spwas spin on the gear so it was a press fit issue, but i will be welding the modded oil pumps from now on
@shannonstratton31643 жыл бұрын
If I put the 6bt pump in a 4bt the pump casting doesn't sit tight against the block face, does a spacer need to be made to take up that gap? Thanks.
@CUTTERUPROB3 жыл бұрын
The pump shouldn’t seat on the flange it’s to seat on the inside of the block
@usewhatyouhave6975 Жыл бұрын
Can you run a 94 and latter oil pump on a 1991 12 valve?
@CUTTERUPROB Жыл бұрын
Yep. Just make sure the oil pan have clearance
@usewhatyouhave6975 Жыл бұрын
Awesome thanks man. Getting hard to find part listings in Canada for the 1st Gen trucks!
@jpop249911 ай бұрын
@@CUTTERUPROB Hey Rob, what is this about oil pan clearance on VE engines using later style oil pumps?
@radspeed31333 жыл бұрын
So i have an 05 5.9 that runs less than 40psi at idle and just over that off idle at temp. Would that be weak pump or sludge? 266k miles on it going to do timing cover seal and main just thinking while I’m there might as well do it. Not sure if it’ll make a difference though.
@CUTTERUPROB3 жыл бұрын
thats enough at stock rpm range. but if to replace the oil bypass valve and the pressure relief valve that will lots of the fix a low oil pressure
@timothymroberts29493 жыл бұрын
Good information
@CUTTERUPROB3 жыл бұрын
Thanks
@onemanoperation54593 жыл бұрын
I’ll be running a compound on my 98 12v cummins and I was thinking about getting HV oil pump, is there a specific brand or a place that you would recommend? Regards from Florida!
@CUTTERUPROB3 жыл бұрын
I like the melling oil pumps myself or a Cummins pump
@robsnodgrass91519 күн бұрын
@@onemanoperation5459 not to differ from Rob's recommendations, but I have found great deals on Cummins marine parts from Florida boat parts suppliers during winter. Couple years back I sourced my 12v oil pump for $38.
@jesserasso10423 жыл бұрын
What about the milled down 8.3l one that pdd sells that's a good one
@CUTTERUPROB3 жыл бұрын
they are one of a few
@Mechanickirk3 жыл бұрын
What's the part number of that VP44 oil pump?
@CUTTERUPROB3 жыл бұрын
i am not sure off the top of my head, but any 12v oil pumps company call high volume is a vp44 pump
@BackCountryWrenching3 жыл бұрын
can you run a 12v oil pump in a 4bt without issues
@CUTTERUPROB3 жыл бұрын
you can if your planning on having compounds, by pass filter and oil cooler. have to watch you do you don't move to much oil
@jesserasso10423 жыл бұрын
Oops sorry I should of watched the rest of the video 😂